Yusuke Nakamura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yusuke Nakamura has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Akihiro Sasoh
Department of Aerospace Engineering, Nagoya University, Nagoya, Japan
12 shared publications Atsushi Isomura
5 shared publicationsAkihiro Sasoh
4 shared publications- Gaku Fukushima
Department of Aerospace Engineering, Nagoya University, Nagoya, Japan
4 shared publications Gakuto Sekine
3 shared publications- Jun Hagiwara
Department of Aerospace Engineering, Nagoya University, Nagoya, Japan
3 shared publications
Latest Publications
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Attenuation and modulation of weak shock waves by a porous wall layer in a shock tube
Interactions between shock waves and porous materials can modulate wave behavior, as reflected in changes in the post-shock pressure. This study investigated the modulation of weak shock waves at incident shock Mach numbers of Ms,i = 1.03–1.21 using an open-cell porous layer installed on the bottom wall of a rectangular shock tube. Upon encountering the porous-wall section, the incident shock was partially diffracted toward the porous layer and reflected on the bottom wall, yielding a wave system comprising the leading shock wave (LSW), expansion waves, and reflected shock wave (RSW). These shock waves eventually coalesced to form a merged shock wave (MSW), with its post-shock pressure depended on Ms,i, the propagation distance, and the porous-layer thickness. The MSW exhibited a significantly reduced post-shock overpressure and a smeared pressure rise behind it. This attenuation was described by introducing the Chester–Chisnell–Whitham (CCW) model to account for shock-wave diffraction, thereby comparing it with the conventionally used Frolov mass-suction model. The proposed CCW-based model better reproduced the attenuation observed in closed-tube experiments. The LSW attenuation increased with shock strength. However, weaker shocks achieved greater overall MSW attenuation because both the LSW and RSW underwent greater attenuation before merging. At Ms,i=1.03, where the porous-layer thickness was 0.2 times the shock-tube height, the shock-induced overpressure was reduced by up to 90% over a propagation distance equivalent to 40.5 times this height. The study findings hold promise for attenuating weak shock waves in advanced applications, e.g., in tunnels for ultrahigh-speed trains powered by superconducting linear motors.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Attenuation and modulation of weak shock waves by a porous wall layer in a shock tube
Interactions between shock waves and porous materials can modulate wave behavior, as reflected in changes in the post-shock pressure. This study investigated the modulation of weak shock waves at incident shock Mach numbers of Ms,i = 1.03–1.21 using an open-cell porous layer installed on the bottom wall of a rectangular shock tube. Upon encountering the porous-wall section, the incident shock was partially diffracted toward the porous layer and reflected on the bottom wall, yielding a wave system comprising the leading shock wave (LSW), expansion waves, and reflected shock wave (RSW). These shock waves eventually coalesced to form a merged shock wave (MSW), with its post-shock pressure depended on Ms,i, the propagation distance, and the porous-layer thickness. The MSW exhibited a significantly reduced post-shock overpressure and a smeared pressure rise behind it. This attenuation was described by introducing the Chester–Chisnell–Whitham (CCW) model to account for shock-wave diffraction, thereby comparing it with the conventionally used Frolov mass-suction model. The proposed CCW-based model better reproduced the attenuation observed in closed-tube experiments. The LSW attenuation increased with shock strength. However, weaker shocks achieved greater overall MSW attenuation because both the LSW and RSW underwent greater attenuation before merging. At Ms,i=1.03, where the porous-layer thickness was 0.2 times the shock-tube height, the shock-induced overpressure was reduced by up to 90% over a propagation distance equivalent to 40.5 times this height. The study findings hold promise for attenuating weak shock waves in advanced applications, e.g., in tunnels for ultrahigh-speed trains powered by superconducting linear motors.
- Open Access
- 14 October 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (6) , 721-737
Experimental investigation of the Chester problem with weak shock waves propagating in converging ducts with quasi-steady flow
The Chester problem (Adv. Appl. Mech. 6:119–152, 1960) introduces a quasi-one-dimensional (quasi-1D) analytical solution developed by Chester based on Chester–Chisnell–Whitham (CCW) theory (Proc. R. Soc. Lond. A 232:350–370, 1955; Lond. Edinb. Philos. Mag. 45:1293–1301, 1954; J. Fluid Mech. 2:286–298, 1957; J. Fluid Mech. 4:337–360, 1958) addressing the interaction between a steady flow within a converging–diverging duct and a shock wave entering from the converging section. Although Chester’s solution provided approximate results for both weak and strong shock waves, this study derives a solution without limitations on the shock Mach number. Additionally, experiments were conducted using a three-channel shock tube , equipped with two diaphragms with adjustable relative rupture timings, to investigate the interaction between the flow and weak shock waves (shock Mach number 1.01–1.10) in the converging section, where the lower wall is flat. The shock wave reflects off the converging upper wall; however, at particularly low shock Mach numbers, the arrival of the reflected wave at the lower wall is delayed. In such cases, the shock wave near the lower wall, which remains unaffected by duct compression, diverges from the quasi-1D solution, and the pressure behind the shock wave is reduced by the upstream co-directional flow. These findings confirm that the shock wave can be attenuated by the non-turbulent, steady upstream flow.
- 14 October 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (6) , 721-737
Open AccessExperimental investigation of the Chester problem with weak shock waves propagating in converging ducts with quasi-steady flow
The Chester problem (Adv. Appl. Mech. 6:119–152, 1960) introduces a quasi-one-dimensional (quasi-1D) analytical solution developed by Chester based on Chester–Chisnell–Whitham (CCW) theory (Proc. R. Soc. Lond. A 232:350–370, 1955; Lond. Edinb. Philos. Mag. 45:1293–1301, 1954; J. Fluid Mech. 2:286–298, 1957; J. Fluid Mech. 4:337–360, 1958) addressing the interaction between a steady flow within a converging–diverging duct and a shock wave entering from the converging section. Although Chester’s solution provided approximate results for both weak and strong shock waves, this study derives a solution without limitations on the shock Mach number. Additionally, experiments were conducted using a three-channel shock tube , equipped with two diaphragms with adjustable relative rupture timings, to investigate the interaction between the flow and weak shock waves (shock Mach number 1.01–1.10) in the converging section, where the lower wall is flat. The shock wave reflects off the converging upper wall; however, at particularly low shock Mach numbers, the arrival of the reflected wave at the lower wall is delayed. In such cases, the shock wave near the lower wall, which remains unaffected by duct compression, diverges from the quasi-1D solution, and the pressure behind the shock wave is reduced by the upstream co-directional flow. These findings confirm that the shock wave can be attenuated by the non-turbulent, steady upstream flow.
- Open Access
- 9 September 2025
- Published by Elsevier in Acta Astronautica
- Vol. 238, 215-222
Novel concept of a front-intake solar array wing for atmospheric drag compensation in very low Earth orbits using air-breathing electric propulsion
- 9 September 2025
- Published by Elsevier in Acta Astronautica
- Vol. 238, 215-222
Open AccessNovel concept of a front-intake solar array wing for atmospheric drag compensation in very low Earth orbits using air-breathing electric propulsion
- Open Access
- 18 August 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 192
Deep-incident-angle performance of pulsed laser propulsion on aluminum
- 18 August 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 192
Open AccessDeep-incident-angle performance of pulsed laser propulsion on aluminum
- Open Access
- 3 April 2025
- Published by Elsevier in Acta Astronautica
- Vol. 232, 557-563
Thrust performance of pulsed-laser ablation impulses for wavelengths of 1064 nm and 532 nm
- 3 April 2025
- Published by Elsevier in Acta Astronautica
- Vol. 232, 557-563
Open AccessThrust performance of pulsed-laser ablation impulses for wavelengths of 1064 nm and 532 nm
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Geometrical impedance matching for weak shock waves at shock tube end wall
When a shock wave encounters an interface with a medium of different acoustic impedance, a reflected wave is generated. It is a shock wave if the medium has a higher acoustic impedance or an expansion fan if the impedance is lower. When the acoustic impedances are perfectly matched, no wave is reflected—a phenomenon known as “impedance matching.” This study aims to achieve a similar effect by varying the geometry of the shock tube exit. Assuming a steady-state, quasi-one-dimensional and subsonic post flow, we derived the exit geometry condition under which neither shock waves nor expansion waves are reflected. To validate this condition, we conducted shock tube experiments with shock Mach numbers up to approximately 1.07, and found that the shock wave reflection behavior is influenced not only by the cross-sectional area ratio of the tube but also by the specific shape of the orifice. In tests with a simple converging orifice shape, a pressure spike occurred due to the leading reflected shock wave before the pressure stabilized. The overpressure of this spike was reduced to 7×10−3 times the pressure ahead of the spike by installing perforated sections and a porous metal body on the sidewall just upstream of the orifice. This study offers a new approach to suppress post-shock pressure fluctuations in practical applications such as high-speed trains entering tunnels and within exhaust pipes of internal combustion engines, as well as to extend the test duration of shock tube experiments.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Geometrical impedance matching for weak shock waves at shock tube end wall
When a shock wave encounters an interface with a medium of different acoustic impedance, a reflected wave is generated. It is a shock wave if the medium has a higher acoustic impedance or an expansion fan if the impedance is lower. When the acoustic impedances are perfectly matched, no wave is reflected—a phenomenon known as “impedance matching.” This study aims to achieve a similar effect by varying the geometry of the shock tube exit. Assuming a steady-state, quasi-one-dimensional and subsonic post flow, we derived the exit geometry condition under which neither shock waves nor expansion waves are reflected. To validate this condition, we conducted shock tube experiments with shock Mach numbers up to approximately 1.07, and found that the shock wave reflection behavior is influenced not only by the cross-sectional area ratio of the tube but also by the specific shape of the orifice. In tests with a simple converging orifice shape, a pressure spike occurred due to the leading reflected shock wave before the pressure stabilized. The overpressure of this spike was reduced to 7×10−3 times the pressure ahead of the spike by installing perforated sections and a porous metal body on the sidewall just upstream of the orifice. This study offers a new approach to suppress post-shock pressure fluctuations in practical applications such as high-speed trains entering tunnels and within exhaust pipes of internal combustion engines, as well as to extend the test duration of shock tube experiments.
- Open Access
- 19 July 2024
- Published by Elsevier in Acta Astronautica
- Vol. 223, 426-434
Time- and angular-distribution of ion current in pulse-laser ablation plume of aluminum
- 19 July 2024
- Published by Elsevier in Acta Astronautica
- Vol. 223, 426-434
Open AccessTime- and angular-distribution of ion current in pulse-laser ablation plume of aluminum
- 3 May 2024
- Published by Springer Nature
- p. 61-79
Laser Propulsion and Demonstrations
- 3 May 2024
- Published by Springer Nature
- p. 143-178
Modeling and Theoretical Studies on Beamed-Induced Plasma
- 3 May 2024
- Published by Springer Nature
- p. 143-178
Modeling and Theoretical Studies on Beamed-Induced Plasma
- 9 October 2023
- Published by Elsevier in Optics & Laser Technology
- Vol. 169
Laser ablation impulse dependence on beam Spatial-Profile
- 9 October 2023
- Published by Elsevier in Optics & Laser Technology
- Vol. 169
Laser ablation impulse dependence on beam Spatial-Profile