Gaku Fukushima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gaku Fukushima has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Akihiro Sasoh
Department of Aerospace Engineering, Nagoya University, Nagoya, Japan
6 shared publications - Yusuke Nakamura
Department of Aerospace Engineering, Nagoya University, Nagoya, Japan
4 shared publications - Keiichi Kitamura
Graduate School of Engineering Science, Yokohama National University
3 shared publications Jun Hagiwara
Department of Aerospace Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603, Japan
2 shared publications- Akira Iwakawa
Department of Aerospace Engineering, Nagoya University, Nagoya, Japan
1 shared publication D. Custodio
Department of Aerospace Engineering, Nagoya University, Nagoya, Japan
1 shared publication
Latest Publications
- Open Access
- 14 October 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (6) , 721-737
Experimental investigation of the Chester problem with weak shock waves propagating in converging ducts with quasi-steady flow
The Chester problem (Adv. Appl. Mech. 6:119–152, 1960) introduces a quasi-one-dimensional (quasi-1D) analytical solution developed by Chester based on Chester–Chisnell–Whitham (CCW) theory (Proc. R. Soc. Lond. A 232:350–370, 1955; Lond. Edinb. Philos. Mag. 45:1293–1301, 1954; J. Fluid Mech. 2:286–298, 1957; J. Fluid Mech. 4:337–360, 1958) addressing the interaction between a steady flow within a converging–diverging duct and a shock wave entering from the converging section. Although Chester’s solution provided approximate results for both weak and strong shock waves, this study derives a solution without limitations on the shock Mach number. Additionally, experiments were conducted using a three-channel shock tube , equipped with two diaphragms with adjustable relative rupture timings, to investigate the interaction between the flow and weak shock waves (shock Mach number 1.01–1.10) in the converging section, where the lower wall is flat. The shock wave reflects off the converging upper wall; however, at particularly low shock Mach numbers, the arrival of the reflected wave at the lower wall is delayed. In such cases, the shock wave near the lower wall, which remains unaffected by duct compression, diverges from the quasi-1D solution, and the pressure behind the shock wave is reduced by the upstream co-directional flow. These findings confirm that the shock wave can be attenuated by the non-turbulent, steady upstream flow.
- 14 October 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (6) , 721-737
Open AccessExperimental investigation of the Chester problem with weak shock waves propagating in converging ducts with quasi-steady flow
The Chester problem (Adv. Appl. Mech. 6:119–152, 1960) introduces a quasi-one-dimensional (quasi-1D) analytical solution developed by Chester based on Chester–Chisnell–Whitham (CCW) theory (Proc. R. Soc. Lond. A 232:350–370, 1955; Lond. Edinb. Philos. Mag. 45:1293–1301, 1954; J. Fluid Mech. 2:286–298, 1957; J. Fluid Mech. 4:337–360, 1958) addressing the interaction between a steady flow within a converging–diverging duct and a shock wave entering from the converging section. Although Chester’s solution provided approximate results for both weak and strong shock waves, this study derives a solution without limitations on the shock Mach number. Additionally, experiments were conducted using a three-channel shock tube , equipped with two diaphragms with adjustable relative rupture timings, to investigate the interaction between the flow and weak shock waves (shock Mach number 1.01–1.10) in the converging section, where the lower wall is flat. The shock wave reflects off the converging upper wall; however, at particularly low shock Mach numbers, the arrival of the reflected wave at the lower wall is delayed. In such cases, the shock wave near the lower wall, which remains unaffected by duct compression, diverges from the quasi-1D solution, and the pressure behind the shock wave is reduced by the upstream co-directional flow. These findings confirm that the shock wave can be attenuated by the non-turbulent, steady upstream flow.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Peculiarity of moving weak shock computations: Entropy generation analysis of numerically expressed shock waves
Shock-capturing schemes using a finite volume method represent shock waves using a specific number of cells. Although understanding the behavior of these “numerical shock waves” is crucial owing to their distinct characteristics, which differ from those of theoretical and physical shock waves, moving weak and moderate shock waves have not been thoroughly investigated. In this study, a numerical test and an analysis were conducted to elucidate the properties of numerical moving shock waves. Our numerical test revealed that the outcome is influenced by the shock strength and numerical flux functions. The final state of a moving shock wave can be classified into three regimes (dissipated, transitional, and thinly captured regimes) depending on the shock strength. Peculiarly, weak shocks faced the dissipated regime, and the dissipation was serious at a shock Mach number of 1.01. Computational results were examined with respect to the entropy generation resulting from the propagation of the numerical moving shock wave. The analysis clarified that the thickness of numerical moving shock waves was determined to ensure physically accurate entropy generation. Furthermore, it was clarified that a moving weak shock wave cannot be accurately represented with a thin profile owing to excessive entropy production. This difficulty in handling a small amount of entropy production resulted in the peculiarity of the weak shock wave computations.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Peculiarity of moving weak shock computations: Entropy generation analysis of numerically expressed shock waves
Shock-capturing schemes using a finite volume method represent shock waves using a specific number of cells. Although understanding the behavior of these “numerical shock waves” is crucial owing to their distinct characteristics, which differ from those of theoretical and physical shock waves, moving weak and moderate shock waves have not been thoroughly investigated. In this study, a numerical test and an analysis were conducted to elucidate the properties of numerical moving shock waves. Our numerical test revealed that the outcome is influenced by the shock strength and numerical flux functions. The final state of a moving shock wave can be classified into three regimes (dissipated, transitional, and thinly captured regimes) depending on the shock strength. Peculiarly, weak shocks faced the dissipated regime, and the dissipation was serious at a shock Mach number of 1.01. Computational results were examined with respect to the entropy generation resulting from the propagation of the numerical moving shock wave. The analysis clarified that the thickness of numerical moving shock waves was determined to ensure physically accurate entropy generation. Furthermore, it was clarified that a moving weak shock wave cannot be accurately represented with a thin profile owing to excessive entropy production. This difficulty in handling a small amount of entropy production resulted in the peculiarity of the weak shock wave computations.
- Open Access
- 1 April 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (4)
Improved hybrid approach of monotonic upstream-centered scheme for conservation laws and discontinuity sharpening technique for steady and unsteady flows
In finite-volume methods, monotonic upstream-centered schemes for conservation laws (MUSCL) offer second-order spatial accuracy but tend to produce highly dissipative solutions for density discontinuity and weak shock waves. To address this limitation within a second-order framework, a novel strategy for hybridizing MUSCL with the tangent of the hyperbola interface capturing technique for both steady and unsteady compressible flows is presented. This hybridization optimizes the process based on the degree of nonlinearity and discontinuity around the target cells, providing a novel method to sharply resolve weak shock waves and robustly compute strong shock waves within the hybrid scheme. The proposed scheme sharply captures exceedingly weak shock waves that conventional MUSCL fails to resolve accurately due to excessive numerical dissipation. Furthermore, for resolving small vortices induced by instability at slip lines, computational results demonstrate high-resolution surpassing fifth-order spatial accuracy schemes within this second-order spatial accuracy framework with less computational cost. Moreover, the scheme exhibits commendable convergence and robustness when applied to steady-state problems featuring strong shock waves. This scheme offers a more precise and high-resolution alternative to conventional MUSCL for compressible flow computations, as it requires no additional stencil for reconstruction, unlike conventional fifth-order schemes.
- 1 April 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (4)
Open AccessImproved hybrid approach of monotonic upstream-centered scheme for conservation laws and discontinuity sharpening technique for steady and unsteady flows
In finite-volume methods, monotonic upstream-centered schemes for conservation laws (MUSCL) offer second-order spatial accuracy but tend to produce highly dissipative solutions for density discontinuity and weak shock waves. To address this limitation within a second-order framework, a novel strategy for hybridizing MUSCL with the tangent of the hyperbola interface capturing technique for both steady and unsteady compressible flows is presented. This hybridization optimizes the process based on the degree of nonlinearity and discontinuity around the target cells, providing a novel method to sharply resolve weak shock waves and robustly compute strong shock waves within the hybrid scheme. The proposed scheme sharply captures exceedingly weak shock waves that conventional MUSCL fails to resolve accurately due to excessive numerical dissipation. Furthermore, for resolving small vortices induced by instability at slip lines, computational results demonstrate high-resolution surpassing fifth-order spatial accuracy schemes within this second-order spatial accuracy framework with less computational cost. Moreover, the scheme exhibits commendable convergence and robustness when applied to steady-state problems featuring strong shock waves. This scheme offers a more precise and high-resolution alternative to conventional MUSCL for compressible flow computations, as it requires no additional stencil for reconstruction, unlike conventional fifth-order schemes.
- 17 October 2022
- Published by American Physical Society (APS) in Physical Review E
- Vol. 106 (4) , L043001
Petal formation law in a cellophane diaphragm subjected to a pressure difference
In this study, a layer of cellophane, subjected to an air-pressure difference, was ruptured using a piercing needle. Accordingly, petal-like fragmentation was observed in the layer via high-speed imaging. Two types of crack-propagation regimes were subsequently observed experimentally. If a tensile stress lower than 20.6 MPa acted on the cellophane diaphragm, a single crack was generated, whose propagation speed was lower than that under higher-stress conditions. For tensile stresses greater than 23.7 MPa, the crack-propagation speed remained constant at approximately 0.86 km/s, even after altering the device size, pressure, and humidity on the low-pressure side. The number of cracks equidistant from the piercing point was expressed as a linear function of the tensile stress acting on the diaphragm.
- 17 October 2022
- Published by American Physical Society (APS) in Physical Review E
- Vol. 106 (4) , L043001
Petal formation law in a cellophane diaphragm subjected to a pressure difference
In this study, a layer of cellophane, subjected to an air-pressure difference, was ruptured using a piercing needle. Accordingly, petal-like fragmentation was observed in the layer via high-speed imaging. Two types of crack-propagation regimes were subsequently observed experimentally. If a tensile stress lower than 20.6 MPa acted on the cellophane diaphragm, a single crack was generated, whose propagation speed was lower than that under higher-stress conditions. For tensile stresses greater than 23.7 MPa, the crack-propagation speed remained constant at approximately 0.86 km/s, even after altering the device size, pressure, and humidity on the low-pressure side. The number of cracks equidistant from the piercing point was expressed as a linear function of the tensile stress acting on the diaphragm.
- 20 June 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
On Peculiar Behaviors of Captured Very-Weak Moving Shockwaves
View Video Presentation: https://doi.org/10.2514/6.2022-4127.vid In this research, peculiar behaviors in calculations of weak and very-weak moving shock waves by two-dimensional finite volume methods are investigated. First-order accuracy calculations of moving shock wave with a shock Mach number of 1.01 show anomalous solutions. The observed anomalies are categorized into three types depending on numerical flux functions: unstable growth of shock wave width, overshoots in primitive variables, and failures of calculations. The κ =1/3 MUSCL scheme suppresses the unstable growth of shock wave thickness when numerical flux functions and limiters are carefully selected: A combination of SLAU2 and the van Albada-limited κ =1/3 MUSCL is found the best for computations of moving very-weak shock waves.
- 20 June 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
On Peculiar Behaviors of Captured Very-Weak Moving Shockwaves
View Video Presentation: https://doi.org/10.2514/6.2022-4127.vid In this research, peculiar behaviors in calculations of weak and very-weak moving shock waves by two-dimensional finite volume methods are investigated. First-order accuracy calculations of moving shock wave with a shock Mach number of 1.01 show anomalous solutions. The observed anomalies are categorized into three types depending on numerical flux functions: unstable growth of shock wave width, overshoots in primitive variables, and failures of calculations. The κ =1/3 MUSCL scheme suppresses the unstable growth of shock wave thickness when numerical flux functions and limiters are carefully selected: A combination of SLAU2 and the van Albada-limited κ =1/3 MUSCL is found the best for computations of moving very-weak shock waves.
- 1 April 2021
- Published by IOP Publishing in Fluid Dynamics Research
- Vol. 53 (2) , 025504
Losing the shock wave front profile due to interaction with turbulence
In this study, losing the shock wave profiles under interactions with grid turbulence was investigated experimentally and theoretically. We demonstrated that the shock wave contrast on side-view schlieren images gradually decreased to an undetectable level in the experiment. This shock wave ‘vanishment’ occurred at a low shock Mach number with a high turbulent Mach number. With a relatively strong shock wave, the contrast of the shock wave remained detectable although the shock wave profile region was expanded. To understand the shock wave vanishment phenomenon during interaction with turbulence, we established a shock wave vanishment model based on the solution of a one-dimensional interaction between a shock wave and forward induced flow. The criterion of the occurrence of local vanishment of the shock wave was derived as M t ⩾ ( M s 2 − 1 ) / M s , where M t is the turbulent Mach number and M s is the shock Mach number. The proposed shock vanishment model involves the effect of the interaction length and the shock wave recovery characteristics. The derived model explains the vanishment of weak shock wave profile during turbulence with an interaction length of ten times the order of the integral scale of the turbulence, as observed in the experiment.
- 1 April 2021
- Published by IOP Publishing in Fluid Dynamics Research
- Vol. 53 (2) , 025504
Losing the shock wave front profile due to interaction with turbulence
In this study, losing the shock wave profiles under interactions with grid turbulence was investigated experimentally and theoretically. We demonstrated that the shock wave contrast on side-view schlieren images gradually decreased to an undetectable level in the experiment. This shock wave ‘vanishment’ occurred at a low shock Mach number with a high turbulent Mach number. With a relatively strong shock wave, the contrast of the shock wave remained detectable although the shock wave profile region was expanded. To understand the shock wave vanishment phenomenon during interaction with turbulence, we established a shock wave vanishment model based on the solution of a one-dimensional interaction between a shock wave and forward induced flow. The criterion of the occurrence of local vanishment of the shock wave was derived as M t ⩾ ( M s 2 − 1 ) / M s , where M t is the turbulent Mach number and M s is the shock Mach number. The proposed shock vanishment model involves the effect of the interaction length and the shock wave recovery characteristics. The derived model explains the vanishment of weak shock wave profile during turbulence with an interaction length of ten times the order of the integral scale of the turbulence, as observed in the experiment.
- 1 March 2021
- Published by Springer Nature in Shock Waves
- Vol. 31 (2) , 101-115
Impacts of grid turbulence on the side projection of planar shock waves
- 1 March 2021
- Published by Springer Nature in Shock Waves
- Vol. 31 (2) , 101-115
Impacts of grid turbulence on the side projection of planar shock waves
- 26 June 2020
- Published by Springer Nature in Shock Waves
- Vol. 30 (5) , 545-557
Influence of cellophane diaphragm rupture processes on the shock wave formation in a shock tube
- 26 June 2020
- Published by Springer Nature in Shock Waves
- Vol. 30 (5) , 545-557
Influence of cellophane diaphragm rupture processes on the shock wave formation in a shock tube