Peizhao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Peizhao Li has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Yu Shi
Dept. of Electrical Engineering, University of Notre Dame, Notre Dame, IN, USA
6 shared publications - Lei Liu
Department of Electrical Engineering, University of Notre Dame, Notre Dame, IN, USA
5 shared publications - Patrick Fay
University of Notre Dame
4 shared publications - Yijing Deng
Dept. of Electrical Engineering, University of Notre Dame, Notre Dame, IN, USA
4 shared publications - Bayaner Arigong
Department of Electrical and Computer Engineering, Florida AM UniversityFlorida State University, Tallahassee, FL, USA
2 shared publications - Han Ren
Department of Electrical Engineering, Washington State University, Vancouver, WA, USA
2 shared publications
Latest Publications
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 15 (3) , 536-540
Integrated Broadband THz Switching Using Photoconductivity Modulation in Si-on-Sapphire Substrates
We report the first experimental demonstration of an alternative approach for achieving integrated broadband terahertz (THz) switching functionality, based on photoconductivity modulation in thin film Si on low-loss sapphire substrates. By employing a silicon thin film mesa (14×14 μm²) on a Silicon-on-Sapphire (SoS) substrate (with 1.5-μm-thick silicon and 600-μm-thick sapphire), an optically-controlled THz switch integrated with low-loss CPW transmission lines operating from 110 GHz to 220 GHz has been designed, fabricated, and characterized. To control the switch in this prototype demonstration, a 915 nm laser diode was used to illuminate the silicon mesa through an optical fiber. The switch performance was measured on-wafer in both D- and G-band; an average on-state insertion loss of ∼3.5 dB (with minimum insertion loss of 2.5 and 1.8 dB at 160 and 200 GHz), and an off-state isolation greater than 20 dB across the entire frequency range have been achieved. This performance can be further greatly improved, and is comparable to or better than competing approaches, with the advantage that this approach allows seamless integration of the switch with passive components on low-loss sapphire substrates. This makes the reported approach promising for developing high-performance and compact THz switches for next-generation adaptive circuits and systems.
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 15 (3) , 536-540
Integrated Broadband THz Switching Using Photoconductivity Modulation in Si-on-Sapphire Substrates
We report the first experimental demonstration of an alternative approach for achieving integrated broadband terahertz (THz) switching functionality, based on photoconductivity modulation in thin film Si on low-loss sapphire substrates. By employing a silicon thin film mesa (14×14 μm²) on a Silicon-on-Sapphire (SoS) substrate (with 1.5-μm-thick silicon and 600-μm-thick sapphire), an optically-controlled THz switch integrated with low-loss CPW transmission lines operating from 110 GHz to 220 GHz has been designed, fabricated, and characterized. To control the switch in this prototype demonstration, a 915 nm laser diode was used to illuminate the silicon mesa through an optical fiber. The switch performance was measured on-wafer in both D- and G-band; an average on-state insertion loss of ∼3.5 dB (with minimum insertion loss of 2.5 and 1.8 dB at 160 and 200 GHz), and an off-state isolation greater than 20 dB across the entire frequency range have been achieved. This performance can be further greatly improved, and is comparable to or better than competing approaches, with the advantage that this approach allows seamless integration of the switch with passive components on low-loss sapphire substrates. This makes the reported approach promising for developing high-performance and compact THz switches for next-generation adaptive circuits and systems.
- 3 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 13 (3) , 286-296
Polarization-Resolved THz Imaging With Orthogonal Heterostructure Backward Diode Detectors
A fully integrated lens-coupled dual-polarization detector for imaging was designed, fabricated, and characterized in the terahertz (THz) region. Two zero-bias heterostructure backward diodes (HBDs) were monolithically integrated into a planar dual-polarization annular-slot antenna. An impedance matching network consisting of an interdigitated DC block and shorted stubs was implemented for maximum power transfer. The fabricated chip was then mounted on an extended hemispherical silicon lens for high antenna efficiency. The performance of the integrated detector has been characterized at 200 GHz. The detector module can simultaneously measure the two orthogonal linear polarized components of the incident THz waves, and hence obtain the polarization direction. On the basis of this polarimetric detection, polarization-resolved imaging of a Gaussian beam, as well as birefringent samples, was performed using the integrated detectors. The angular resolution of the polarization detection has been demonstrated to be as small as 3°. The single-pixel detector demonstrated here is amenable to array applications for THz focal-plane arrays that will have a significant impact on a wide range of remote sensing, though-barrier imaging, and detection/identification applications.
- 3 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 13 (3) , 286-296
Polarization-Resolved THz Imaging With Orthogonal Heterostructure Backward Diode Detectors
A fully integrated lens-coupled dual-polarization detector for imaging was designed, fabricated, and characterized in the terahertz (THz) region. Two zero-bias heterostructure backward diodes (HBDs) were monolithically integrated into a planar dual-polarization annular-slot antenna. An impedance matching network consisting of an interdigitated DC block and shorted stubs was implemented for maximum power transfer. The fabricated chip was then mounted on an extended hemispherical silicon lens for high antenna efficiency. The performance of the integrated detector has been characterized at 200 GHz. The detector module can simultaneously measure the two orthogonal linear polarized components of the incident THz waves, and hence obtain the polarization direction. On the basis of this polarimetric detection, polarization-resolved imaging of a Gaussian beam, as well as birefringent samples, was performed using the integrated detectors. The angular resolution of the polarization detection has been demonstrated to be as small as 3°. The single-pixel detector demonstrated here is amenable to array applications for THz focal-plane arrays that will have a significant impact on a wide range of remote sensing, though-barrier imaging, and detection/identification applications.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 12 (6) , 658-666
A Cost-Effective Approach for Achieving Subwavelength THz Imaging Using Photoinduced Coded-Apertures on Mesa-Array Structures
A novel and cost-effective approach for high resolution terahertz imaging using photo-induced coded-apertures on micromachined mesa array structures is reported. The mesa-array structures are designed to have subwavelength electrically-isolated mesas for generation of high-fidelity photopatterns for THz imaging. A Si mesa array prototype structure was successfully fabricated and tested. Measurements show that a modulation depth of ∼22 dB was obtained in the frequency range of 740-750 GHz under a light intensity of 11.7 W/cm 2 , which agrees well with theoretical analysis and full-wave simulation. Initial imaging experiments were first performed using 64 pixels (over different areas) for validation and performance evaluation. More advanced imaging using quadrupled pixel number (256 pixels) was conducted in order to resolve subwavelength features. As a result, a wavelength-scale spatial resolution of 400 µm has been successfully demonstrated, and a subwavelength resolution as small as ∼250 µm (0.625λ at 740 GHz) has been shown to be potentially achievable. The proposed photo-induced coded aperture imaging using mesa arrays is promising for developing real-time high-resolution THz imaging with simple system and low cost.
- 26 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 12 (6) , 658-666
A Cost-Effective Approach for Achieving Subwavelength THz Imaging Using Photoinduced Coded-Apertures on Mesa-Array Structures
A novel and cost-effective approach for high resolution terahertz imaging using photo-induced coded-apertures on micromachined mesa array structures is reported. The mesa-array structures are designed to have subwavelength electrically-isolated mesas for generation of high-fidelity photopatterns for THz imaging. A Si mesa array prototype structure was successfully fabricated and tested. Measurements show that a modulation depth of ∼22 dB was obtained in the frequency range of 740-750 GHz under a light intensity of 11.7 W/cm 2 , which agrees well with theoretical analysis and full-wave simulation. Initial imaging experiments were first performed using 64 pixels (over different areas) for validation and performance evaluation. More advanced imaging using quadrupled pixel number (256 pixels) was conducted in order to resolve subwavelength features. As a result, a wavelength-scale spatial resolution of 400 µm has been successfully demonstrated, and a subwavelength resolution as small as ∼250 µm (0.625λ at 740 GHz) has been shown to be potentially achievable. The proposed photo-induced coded aperture imaging using mesa arrays is promising for developing real-time high-resolution THz imaging with simple system and low cost.
- 16 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (7) , 891-894
A 200 GHz Fully Integrated, Polarization-Resolved Quasi-Optical Detector Using Zero-Bias Heterostructure Backward Diodes
We report the design, fabrication, and prototype demonstration of a 200-GHz polarization-resolved quasi-optical detector employing monolithically integrated zero-bias heterostructure backward diodes (HBDs). In this design, polarization resolution is achieved by orthogonally integrating the detectors with a planar dual-polarization annular-slot antenna. The detector chip was fabricated and mounted on an extended hemispherical Si lens to enhance antenna efficiency in the millimeter-wave to terahertz region. The responsivity and radiation patterns of the detector were characterized experimentally; good agreement with theoretical calculations was obtained. By measuring the outputs of two orthogonal HBDs as a function of the polarization angle of the incident wave, the planar detector detects intensity and resolves polarization. On the basis of the polarimetric measurement, we further demonstrate the polarization imaging capability of the proposed detector by using it as an imaging system. The detector is promising for developing terahertz polarimetric sensors and imaging arrays in chemical sensing, biomedical imaging, and radio astronomy applications.
- 16 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 32 (7) , 891-894
A 200 GHz Fully Integrated, Polarization-Resolved Quasi-Optical Detector Using Zero-Bias Heterostructure Backward Diodes
We report the design, fabrication, and prototype demonstration of a 200-GHz polarization-resolved quasi-optical detector employing monolithically integrated zero-bias heterostructure backward diodes (HBDs). In this design, polarization resolution is achieved by orthogonally integrating the detectors with a planar dual-polarization annular-slot antenna. The detector chip was fabricated and mounted on an extended hemispherical Si lens to enhance antenna efficiency in the millimeter-wave to terahertz region. The responsivity and radiation patterns of the detector were characterized experimentally; good agreement with theoretical calculations was obtained. By measuring the outputs of two orthogonal HBDs as a function of the polarization angle of the incident wave, the planar detector detects intensity and resolves polarization. On the basis of the polarimetric measurement, we further demonstrate the polarization imaging capability of the proposed detector by using it as an imaging system. The detector is promising for developing terahertz polarimetric sensors and imaging arrays in chemical sensing, biomedical imaging, and radio astronomy applications.
- Open Access
- 28 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1407
Computational Analysis of a 200 GHz Phased Array Using Lens-Coupled Annular-Slot Antennas
We report the design, simulation, and analysis of a THz phased array, using lens-coupled annular-slot antennas (ASAs) for potential beyond 5G or 6G wireless communications. For a prototype demonstration, the ASA employed was designed on a high resistivity Si substrate with a radius of 106 μm, and a gap width of 6 um for operation at 200 GHz. In order to achieve higher antenna gain and efficiency, an extended hemispherical silicon lens was also used. To investigate the effect of the silicon lens on the ASA phased array, a 1 × 3 array and 1 × 5 array (the element distance is 0.55λ) were implemented with a silicon lens using different extension lengths. The simulation shows that for a 1 × 3 array, a ±17° scanning angle with an about −10 dB sidelobe level and 11.82 dB gain improvement (compared to the array without lens) can be achieved using a lens radius of 5000 μm and an extension length of 1000 μm. A larger scanning angle of ±31° can also be realized by a 1 × 5 array (using a shorter extension length of 250 μm). The approach of designing a 200 GHz lens-coupled phased array reported here is informative and valuable for the future development of wireless communication technologies.
- 28 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1407
Open AccessComputational Analysis of a 200 GHz Phased Array Using Lens-Coupled Annular-Slot Antennas
We report the design, simulation, and analysis of a THz phased array, using lens-coupled annular-slot antennas (ASAs) for potential beyond 5G or 6G wireless communications. For a prototype demonstration, the ASA employed was designed on a high resistivity Si substrate with a radius of 106 μm, and a gap width of 6 um for operation at 200 GHz. In order to achieve higher antenna gain and efficiency, an extended hemispherical silicon lens was also used. To investigate the effect of the silicon lens on the ASA phased array, a 1 × 3 array and 1 × 5 array (the element distance is 0.55λ) were implemented with a silicon lens using different extension lengths. The simulation shows that for a 1 × 3 array, a ±17° scanning angle with an about −10 dB sidelobe level and 11.82 dB gain improvement (compared to the array without lens) can be achieved using a lens radius of 5000 μm and an extension length of 1000 μm. A larger scanning angle of ±31° can also be realized by a 1 × 5 array (using a shorter extension length of 250 μm). The approach of designing a 200 GHz lens-coupled phased array reported here is informative and valuable for the future development of wireless communication technologies.
- 29 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
A 200 GHz Switchable Beam-Steering Phased Array Using Lens-Coupled Annular-Slot Antennas
We report the design and simulation of a THz switchable beam-steering phased array using lens-coupled annular-slot antennas (ASA). For a prototype demonstration, the antenna employed was designed on a high resistivity Si substrate with a radius of 106 um, and a gap width of 6 um (with return loss of 31.8 dB, and 10 dB bandwidth of 13%) for operation at 200 GHz. To achieve a reasonably low side lobe level, a 1×5 array with an element spacing of 0.56λ is utilized. The array is then attached to an extended hemi-spherical Si lens with a radius of 5 mm for high antenna efficiency in the THz region and the succeeding antenna elements are fed by a Nolen matrix and a high performance optically controlled switch network. By switching the input ports of the Nolen matrix, equal magnitude and unique progressive phase difference can be generated for feeding the antennas and steering the antenna beam. The simulation results show that five different beam angles (i.e., -33°, -15°, 0°, 15°, 33°) with the gain of around 15 dB can be achieved. The lens-coupled phased array has great potentials for advanced THz imaging and communication applications.
- 29 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
A 200 GHz Switchable Beam-Steering Phased Array Using Lens-Coupled Annular-Slot Antennas
We report the design and simulation of a THz switchable beam-steering phased array using lens-coupled annular-slot antennas (ASA). For a prototype demonstration, the antenna employed was designed on a high resistivity Si substrate with a radius of 106 um, and a gap width of 6 um (with return loss of 31.8 dB, and 10 dB bandwidth of 13%) for operation at 200 GHz. To achieve a reasonably low side lobe level, a 1×5 array with an element spacing of 0.56λ is utilized. The array is then attached to an extended hemi-spherical Si lens with a radius of 5 mm for high antenna efficiency in the THz region and the succeeding antenna elements are fed by a Nolen matrix and a high performance optically controlled switch network. By switching the input ports of the Nolen matrix, equal magnitude and unique progressive phase difference can be generated for feeding the antennas and steering the antenna beam. The simulation results show that five different beam angles (i.e., -33°, -15°, 0°, 15°, 33°) with the gain of around 15 dB can be achieved. The lens-coupled phased array has great potentials for advanced THz imaging and communication applications.
- 22 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (12) , 5031-5039
Phase Shifter-Relaxed and Control-Relaxed Continuous Steering Multiple Beamforming 4 × 4 Butler Matrix Phased Array
A novel continuous tunable phase progression beamforming feeding network is proposed using 4x 4 Butler matrix and tunable phase shifters. To tune the progressive phase difference at the output ports of matrix network, four phase shifters (i.e. two phase shifters with 90° tuning range, and other two with 180° phase tuning range) are integrated within the Butler matrix. Two-channel digital voltages control all four phase shifters simultaneously to tune the phase difference in 90° range for each input excitation of the Butler matrix, and the 360° full range of the progressive phase difference is realized by switching four input ports. The theoretical analysis is carried out to reduce the number of the phase shifters as well as their phase tuning ranges, and the closed-form equations are derived to minimize the control complexity. To prove the design concept, a prototype of the proposed tunable Butler matrix is designed at 5.8 GHz, and the experimental results agree well with the simulation results to prove the design theory. Integrating with four patch antenna elements, the measured radiation beam is steered from -51° to 52° by tuning two control voltages.
- 22 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (12) , 5031-5039
Phase Shifter-Relaxed and Control-Relaxed Continuous Steering Multiple Beamforming 4 × 4 Butler Matrix Phased Array
A novel continuous tunable phase progression beamforming feeding network is proposed using 4x 4 Butler matrix and tunable phase shifters. To tune the progressive phase difference at the output ports of matrix network, four phase shifters (i.e. two phase shifters with 90° tuning range, and other two with 180° phase tuning range) are integrated within the Butler matrix. Two-channel digital voltages control all four phase shifters simultaneously to tune the phase difference in 90° range for each input excitation of the Butler matrix, and the 360° full range of the progressive phase difference is realized by switching four input ports. The theoretical analysis is carried out to reduce the number of the phase shifters as well as their phase tuning ranges, and the closed-form equations are derived to minimize the control complexity. To prove the design concept, a prototype of the proposed tunable Butler matrix is designed at 5.8 GHz, and the experimental results agree well with the simulation results to prove the design theory. Integrating with four patch antenna elements, the measured radiation beam is steered from -51° to 52° by tuning two control voltages.
- 18 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (4) , 387-390
A Symmetric Beam-Phased Array Fed by a Nolen Matrix Using 180° Couplers
This letter presents a new microstrip line-phased array using 3 x 3 Nolen matrix - with three inputs and three output ports. For each input port excitation, the signal is divided into three equal magnitudes and unique progressive phase shifts at its output ports. The proposed microwave network is composed of three 180° couplers with two of them having identical coupling factors and two microstrip line-phase shifters. To verify the proposed design concept, a prototype of the feeding network working at 5.8 GHz is designed, fabricated, and measured. Both simulation and measurement results are in good agreement with the theoretical prediction.
- 18 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (4) , 387-390
A Symmetric Beam-Phased Array Fed by a Nolen Matrix Using 180° Couplers
This letter presents a new microstrip line-phased array using 3 x 3 Nolen matrix - with three inputs and three output ports. For each input port excitation, the signal is divided into three equal magnitudes and unique progressive phase shifts at its output ports. The proposed microwave network is composed of three 180° couplers with two of them having identical coupling factors and two microstrip line-phase shifters. To verify the proposed design concept, a prototype of the feeding network working at 5.8 GHz is designed, fabricated, and measured. Both simulation and measurement results are in good agreement with the theoretical prediction.