Pengcheng Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pengcheng Liu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Zheng Wang
School of Electrical Engineering, Southeast University, Nanjing, China
12 shared publications - Yang Xu
The University of Tennessee
10 shared publications - Jiangbiao He
Department of Electrical Engineering and Computer Science, University of Tennessee, Knoxville, TN, USA
4 shared publications - Yunwei Li
University of Alberta
4 shared publications - Ming Cheng
Southeast University
3 shared publications - Zhixiang Zou
Southeast University
3 shared publications
Latest Publications
- 16 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 66-77
Modeling and Analysis of Speed Control Loop for Low Carrier Ratio PWM CSI-Fed Motor Drives Based on Discrete-Time State Space Equation
The traditional engineering speed loop modeling and analysis simplifies the control loop by considering the inner current control loop as a first-order lag without considering the dq-axis cross-coupling issue of inner control loops, which is not suitable for low carrier ratio applications with distinct delay effect and cross-coupling issues. Aiming at this problem, this article establishes the inner control loop based on a discrete-time state space equation, which fully reflects the impact of the dq-axis cross-coupling issue caused by synchronous rotating coordinate transformation, as well as the huge digital delay caused by low carrier ratio for pulse width modulation (PWM) current source inverter (CSI)-fed motor drives. Then, an accurate outer speed control loop is established by cascading the inner control loop with the speed controller. The proposed speed control loop model can provide a theoretical basis for analyzing system stability and dynamic performance of a PWM CSI-fed drive system with a low carrier ratio. The correctness of the modeling methodology is theoretically supported by the analysis of the root locus diagram and experimentally verified on a laboratory prototype.
- 16 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 66-77
Modeling and Analysis of Speed Control Loop for Low Carrier Ratio PWM CSI-Fed Motor Drives Based on Discrete-Time State Space Equation
The traditional engineering speed loop modeling and analysis simplifies the control loop by considering the inner current control loop as a first-order lag without considering the dq-axis cross-coupling issue of inner control loops, which is not suitable for low carrier ratio applications with distinct delay effect and cross-coupling issues. Aiming at this problem, this article establishes the inner control loop based on a discrete-time state space equation, which fully reflects the impact of the dq-axis cross-coupling issue caused by synchronous rotating coordinate transformation, as well as the huge digital delay caused by low carrier ratio for pulse width modulation (PWM) current source inverter (CSI)-fed motor drives. Then, an accurate outer speed control loop is established by cascading the inner control loop with the speed controller. The proposed speed control loop model can provide a theoretical basis for analyzing system stability and dynamic performance of a PWM CSI-fed drive system with a low carrier ratio. The correctness of the modeling methodology is theoretically supported by the analysis of the root locus diagram and experimentally verified on a laboratory prototype.
- 17 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 962-975
Comparative Study of Advanced Modulation and Control Schemes for Dual Three-Phase PMSM Drives With Low Switching Frequencies
In this paper, multiple advanced low-switching-frequency modulation and control schemes are investigated for dual three-phase permanent-magnet synchronous motor (PMSM) drives. The modulation schemes under investigation include multisampling space vector modulation (MS-SVM), selective harmonic elimination pulse width modulation (SHEPWM) and synchronous optimal pulse width modulation (SOPWM) while the control schemes include complex vector control, model predictive control (MPC) and flux trajectory control-based model predictive pulse pattern control (MP 3 C). The difference between three-phase and dual three-phase PMSM drives at low switching frequencies is analyzed. Moreover, an optimal pulse width modulation (PWM)-based MP 3 C scheme is proposed for the dual three-phase PMSM, where the optimal PWM modulation and MP 3 C control are combined such that the optimal steady-state and dynamic control performance is achieved among the modulation and control schemes investigated. Experimental results are given to compare and validate the proposed control scheme.
- 17 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (1) , 962-975
Comparative Study of Advanced Modulation and Control Schemes for Dual Three-Phase PMSM Drives With Low Switching Frequencies
In this paper, multiple advanced low-switching-frequency modulation and control schemes are investigated for dual three-phase permanent-magnet synchronous motor (PMSM) drives. The modulation schemes under investigation include multisampling space vector modulation (MS-SVM), selective harmonic elimination pulse width modulation (SHEPWM) and synchronous optimal pulse width modulation (SOPWM) while the control schemes include complex vector control, model predictive control (MPC) and flux trajectory control-based model predictive pulse pattern control (MP 3 C). The difference between three-phase and dual three-phase PMSM drives at low switching frequencies is analyzed. Moreover, an optimal pulse width modulation (PWM)-based MP 3 C scheme is proposed for the dual three-phase PMSM, where the optimal PWM modulation and MP 3 C control are combined such that the optimal steady-state and dynamic control performance is achieved among the modulation and control schemes investigated. Experimental results are given to compare and validate the proposed control scheme.
- 11 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (1) , 762-775
Discrete-Time Complex-Vector Model Based Closed-Loop Current Controller for CSC-Fed PMAC Machine Systems With Low Carrier Ratios
Pulsewidth modulated (PWM) current-source converters (CSCs) have been attractive for high-power adjustable-speed machine systems with low carrier ratios. However, the high-order nonlinear model of CSC-fed machine systems, the distinct digital delay from the low carrier ratios, and the cross-coupling caused by coordinate transformation bring great challenges to design of high-performance stator current controller for such kind of machine systems. Firstly, this article derives the discrete-time complex-vector model for the CSC-fed permanent-magnet ac (PMAC) machine system with low carrier ratios considering the distinct digital delay and cross-coupling effect mentioned above. On that basis, the stator current controller is proposed with the modified controller parameters and the compensation technique to improve both dynamic performance and stability of the CSC-fed PMAC machine systems with low carrier ratios. The theoretical analysis and controller design process have been presented in detail to provide a guide for the model derivation and controller design. The experiments on a laboratory prototype are conducted to verify the effectiveness of the developed modeling and controller.
- 11 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (1) , 762-775
Discrete-Time Complex-Vector Model Based Closed-Loop Current Controller for CSC-Fed PMAC Machine Systems With Low Carrier Ratios
Pulsewidth modulated (PWM) current-source converters (CSCs) have been attractive for high-power adjustable-speed machine systems with low carrier ratios. However, the high-order nonlinear model of CSC-fed machine systems, the distinct digital delay from the low carrier ratios, and the cross-coupling caused by coordinate transformation bring great challenges to design of high-performance stator current controller for such kind of machine systems. Firstly, this article derives the discrete-time complex-vector model for the CSC-fed permanent-magnet ac (PMAC) machine system with low carrier ratios considering the distinct digital delay and cross-coupling effect mentioned above. On that basis, the stator current controller is proposed with the modified controller parameters and the compensation technique to improve both dynamic performance and stability of the CSC-fed PMAC machine systems with low carrier ratios. The theoretical analysis and controller design process have been presented in detail to provide a guide for the model derivation and controller design. The experiments on a laboratory prototype are conducted to verify the effectiveness of the developed modeling and controller.
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (4) , 4779-4791
The Modular Current-Fed High-Frequency Isolated Matrix Converters for Wind Energy Conversion
In this article, a modular current-fed high-frequency transformer isolated matrix converters (CF-HFT-MC) based wind energy conversion system (WECS) is proposed. The CF-HFT-MC module utilizes the high-frequency transformer instead of the line-frequency input transformer, and eliminates the bulky and vulnerable electrolytic capacitors in the WECS. Therefore, the power density, reliability and efficiency of WECS can be increased. Moreover, single-stage power conversion and soft-switching can be achieved in the CF-HFT-MC modules, which can reduce the losses of the system. With the function of electric isolation, the wind turbines can be connected in series through the proposed CF-HFT-MC modules. Thus, the total dc output voltage is increased, which enables the offshore wind farm to be integrated to the current-source-converters based HVdc transmission directly. The modulation, control scheme and power sharing method are analyzed and designed for the proposed CF-HFT-MC based WECS in this article. Both the simulations and the experiments are given to verify the effectiveness of the proposed system.
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (4) , 4779-4791
The Modular Current-Fed High-Frequency Isolated Matrix Converters for Wind Energy Conversion
In this article, a modular current-fed high-frequency transformer isolated matrix converters (CF-HFT-MC) based wind energy conversion system (WECS) is proposed. The CF-HFT-MC module utilizes the high-frequency transformer instead of the line-frequency input transformer, and eliminates the bulky and vulnerable electrolytic capacitors in the WECS. Therefore, the power density, reliability and efficiency of WECS can be increased. Moreover, single-stage power conversion and soft-switching can be achieved in the CF-HFT-MC modules, which can reduce the losses of the system. With the function of electric isolation, the wind turbines can be connected in series through the proposed CF-HFT-MC modules. Thus, the total dc output voltage is increased, which enables the offshore wind farm to be integrated to the current-source-converters based HVdc transmission directly. The modulation, control scheme and power sharing method are analyzed and designed for the proposed CF-HFT-MC based WECS in this article. Both the simulations and the experiments are given to verify the effectiveness of the proposed system.
- 29 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (5) , 5086-5098
Soft-Switching Current-Source Rectifier Based Onboard Charging System for Electric Vehicles
In this article, a novel soft-switching current-source rectifier (CSR) based bidirectional on-board charger (OBC) system is proposed for electric vehicles (EVs) comprising multiple battery sets. Besides the CSR's inherent advantages of higher-quality input voltage waveforms, enhanced short-circuit-current tolerant capability and long lifetime of dc choke, the cascaded configuration of dc choppers can implement the higher dc-link voltage with multiple low-voltage battery sets, and the low-voltage devices can be used. With the auxiliary resonant circuit in dc link, the soft-switching operation can be achieved for all power switches in the proposed power conversion circuits. Moreover, the high dv/dt caused by high-speed switching silicon carbide devices can be reduced with the capacitor in the auxiliary circuit. The collaborative operation strategy is proposed for the CSR and the dc choppers, which enables reduction of switching frequency of dc choppers and current ripple in dc link simultaneously. The experimental results are presented to verify the performance of the proposed the OBC system.
- 29 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (5) , 5086-5098
Soft-Switching Current-Source Rectifier Based Onboard Charging System for Electric Vehicles
In this article, a novel soft-switching current-source rectifier (CSR) based bidirectional on-board charger (OBC) system is proposed for electric vehicles (EVs) comprising multiple battery sets. Besides the CSR's inherent advantages of higher-quality input voltage waveforms, enhanced short-circuit-current tolerant capability and long lifetime of dc choke, the cascaded configuration of dc choppers can implement the higher dc-link voltage with multiple low-voltage battery sets, and the low-voltage devices can be used. With the auxiliary resonant circuit in dc link, the soft-switching operation can be achieved for all power switches in the proposed power conversion circuits. Moreover, the high dv/dt caused by high-speed switching silicon carbide devices can be reduced with the capacitor in the auxiliary circuit. The collaborative operation strategy is proposed for the CSR and the dc choppers, which enables reduction of switching frequency of dc choppers and current ripple in dc link simultaneously. The experimental results are presented to verify the performance of the proposed the OBC system.
- 20 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (4) , 3292-3302
Current-Fed Isolated Three-Phase Matrix-Type Grid Inverter With Soft-Switching Capability
The grid inverters play an important role in renewable energy systems, transferring the dc power to the ac grid. Galvanic isolation is usually needed between the dc source and the grid due to safety reasons and grounding leakage current mitigation. In this article, a soft-switching isolated grid inverter is proposed based on the current-fed matrix-type configuration. The topology of this converter is composed of a current-fed H-bridge on the side of dc source and a direct matrix converter on the grid side, which are linked by a high-frequency transformer. The current-fed H-bridge on the primary-side can smooth the dc-source current and control the dc-source current directly. The avoidance of dc-link energy-storage element in the single-stage matrix converter can prolong the system's life. A space-vector-modulation-based soft-switching scheme is proposed for the matrix converter on the grid side and a model-based commutation method is adopted in the current-fed H-bridge on the dc side. With the proposed modulation methods, the soft switching can be realized for all devices in the converter. Finally, a laboratory prototype of the proposed converter has been built to verify the effectiveness of the proposed method experimentally.
- 20 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (4) , 3292-3302
Current-Fed Isolated Three-Phase Matrix-Type Grid Inverter With Soft-Switching Capability
The grid inverters play an important role in renewable energy systems, transferring the dc power to the ac grid. Galvanic isolation is usually needed between the dc source and the grid due to safety reasons and grounding leakage current mitigation. In this article, a soft-switching isolated grid inverter is proposed based on the current-fed matrix-type configuration. The topology of this converter is composed of a current-fed H-bridge on the side of dc source and a direct matrix converter on the grid side, which are linked by a high-frequency transformer. The current-fed H-bridge on the primary-side can smooth the dc-source current and control the dc-source current directly. The avoidance of dc-link energy-storage element in the single-stage matrix converter can prolong the system's life. A space-vector-modulation-based soft-switching scheme is proposed for the matrix converter on the grid side and a model-based commutation method is adopted in the current-fed H-bridge on the dc side. With the proposed modulation methods, the soft switching can be realized for all devices in the converter. Finally, a laboratory prototype of the proposed converter has been built to verify the effectiveness of the proposed method experimentally.
- 5 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (10) , 11234-11244
Improved Harmonic Profile for High-Power PWM Current-Source Converters With Modified Space-Vector Modulation Schemes
Pulsewidth-modulated (PWM) current-source converters (CSCs) have the features of simple configuration, reliable short-circuit protection, and sinusoidal ac output voltages. The conventional space-vector modulation (SVM) scheme usually generates high-magnitude low-order harmonics in CSCs with low switching frequency. In this article, two modified SVM schemes, namely MSVM1 and MSVM2, are proposed to improve the harmonic performance for PWM CSCs in the high-power applications with low switching frequencies. The MSVM1 scheme focuses on eliminating the average dwell-time error of current vectors within each sampling period, while the MSVM2 scheme is targeted to achieve the accurate dwell time of current vectors as that of the natural sampling-based SVM scheme. The theoretical analysis and the calculation equations of dwell time are derived for both MSVM1 and MSVM2. The experiments are given to verify the effectiveness of the two modified SVM schemes in improving the harmonic performance of high-power CSCs with low switching frequencies.
- 5 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (10) , 11234-11244
Improved Harmonic Profile for High-Power PWM Current-Source Converters With Modified Space-Vector Modulation Schemes
Pulsewidth-modulated (PWM) current-source converters (CSCs) have the features of simple configuration, reliable short-circuit protection, and sinusoidal ac output voltages. The conventional space-vector modulation (SVM) scheme usually generates high-magnitude low-order harmonics in CSCs with low switching frequency. In this article, two modified SVM schemes, namely MSVM1 and MSVM2, are proposed to improve the harmonic performance for PWM CSCs in the high-power applications with low switching frequencies. The MSVM1 scheme focuses on eliminating the average dwell-time error of current vectors within each sampling period, while the MSVM2 scheme is targeted to achieve the accurate dwell time of current vectors as that of the natural sampling-based SVM scheme. The theoretical analysis and the calculation equations of dwell time are derived for both MSVM1 and MSVM2. The experiments are given to verify the effectiveness of the two modified SVM schemes in improving the harmonic performance of high-power CSCs with low switching frequencies.
- 24 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (1) , 761-771
Zero-Voltage-Switching Current Source Inverter Fed PMSM Drives With Reduced EMI
The SiC devices have attracted more and more attention due to the capability of withstanding higher blocking voltage, higher switching frequency, and higher temperature. However, challenges for SiC devices applied in voltage-source-inverter (VSI) fed motor drives such as electromagnetic interference (EMI) issues and limited over-current capability still limit the further application of SiC devices. In this paper, a novel SiC devices based zero-voltage-switching (ZVS) current-source-inverter (CSI) is proposed for permanent-magnet synchronous motor (PMSM) drive. The key is to propose an auxiliary resonant circuit, which achieves ZVS conditions for all switches in power circuits and reduces the dv/dt of high speed SiC devices. The resonant capacitor in the auxiliary circuit can clamp overvoltage caused by possible open-circuit faults. To further reduce the EMI, the random switching frequency PWM (RSFPWM) is designed for the proposed CSI motor drive. The system configuration, working principle, circuit design and control schemes are described in detail. Both simulations and experiments are presented to verify the effectiveness of the proposed ZVS CSI fed PMSM drive system.
- 24 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (1) , 761-771
Zero-Voltage-Switching Current Source Inverter Fed PMSM Drives With Reduced EMI
The SiC devices have attracted more and more attention due to the capability of withstanding higher blocking voltage, higher switching frequency, and higher temperature. However, challenges for SiC devices applied in voltage-source-inverter (VSI) fed motor drives such as electromagnetic interference (EMI) issues and limited over-current capability still limit the further application of SiC devices. In this paper, a novel SiC devices based zero-voltage-switching (ZVS) current-source-inverter (CSI) is proposed for permanent-magnet synchronous motor (PMSM) drive. The key is to propose an auxiliary resonant circuit, which achieves ZVS conditions for all switches in power circuits and reduces the dv/dt of high speed SiC devices. The resonant capacitor in the auxiliary circuit can clamp overvoltage caused by possible open-circuit faults. To further reduce the EMI, the random switching frequency PWM (RSFPWM) is designed for the proposed CSI motor drive. The system configuration, working principle, circuit design and control schemes are described in detail. Both simulations and experiments are presented to verify the effectiveness of the proposed ZVS CSI fed PMSM drive system.
- 28 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (6) , 4586-4597
Optimal Overlap-Time Distribution of Space Vector Modulation for Current-Source Rectifier
- 28 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (6) , 4586-4597
Optimal Overlap-Time Distribution of Space Vector Modulation for Current-Source Rectifier