Seyed Jalal Hashemi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Seyed Jalal Hashemi has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Ali Sadooghi
Department of Mechanical Engineering Technical and Vocational University (TVU) Tehran Iran
2 shared publications Amir H. Roohi
Department of Mechanical Engineering, Faculty of Industrial and Mechanical Engineering, Qazvin Branch, Islamic Azad University, Qazvin, Iran
2 shared publicationsAlireza Bahadory
1 shared publicationAmir Hossein Roohi
Department of Mechanical Engineering, Faculty of Industrial and Mechanical Engineering, Qazvin Branch, Islamic Azad University, Qazvin, Iran
1 shared publicationAmirhosein Roohi
Department of Mechanical Engineering, Faculty of Industrial and Mechanical Engineering, Qazvin Branch, Islamic Azad University, Qazvin, Iran
1 shared publicationFereshte Davarzani
1 shared publication
Latest Publications
- Open Access
- 23 July 2022
- Published by CMV Verlag in Mechanic of Advanced and Smart Materials
- Vol. 2 (2) , 156-171
Design and Manufacture of Low-Pressure Hydroforming Machine for Aluminum Tubes and Production of Rectangular Cross Section
هیدروفرمینگ لوله بهطور گسترده، در تولید قطعات ساختاری اتومبیل استفاده میشود. یکی از خصوصیات قطعات تولیدشده با این فرایند، نسبت استحکام به وزن بالا میباشد. هیدروفرمینگ لولۀ فشار پایین، یکی از روشهای پیشنهادشده برای حل مشکلات هیدروفرمینگ لوله از قبیل نیاز به فشار بالای سیال و مشکلات آببندی میباشد. روش انجام هیدروفرمینگ فشار پایین لوله، شبیه فشردن جسم جامد است و در آن برخلاف هیدروفرمینگ فشار بالا، قالب بالایی در طول فرایند ثابت نبوده و همزمان با اعمال فشار داخلی به لوله، حرکت کرده و لوله را تحت فشار قرار میدهد. در این مقاله، فرایند هیدروفرمینگ فشار پایین لولههای آلومینیومی AA6063 انجام شده و مقطع گرد لوله بهوسیلۀ فرایند هیدروفرمینگ به مقطع مستطیلی تغییر شکل داده است. همچنین توزیع ضخامت و مقادیر شعاع گوشۀ شکل داده شده، تحت سه مسیر بارگذاری متفاوت بررسی شده است. نتایج نشان میدهد که با افزایش فشار داخلی میتوان به شعاع گوشه کمتری دست پیدا کرد اما نازکشدگی افزایش پیدا میکند. همچنین بیشترین تختی سطح بالایی قطعه، زمانی حاصل میشود که جابجایی قالب بالایی بعد از رسیدن فشار داخلی به مقدار ماکزیمم خود...
- 23 July 2022
- Published by CMV Verlag in Mechanic of Advanced and Smart Materials
- Vol. 2 (2) , 156-171
Open AccessDesign and Manufacture of Low-Pressure Hydroforming Machine for Aluminum Tubes and Production of Rectangular Cross Section
هیدروفرمینگ لوله بهطور گسترده، در تولید قطعات ساختاری اتومبیل استفاده میشود. یکی از خصوصیات قطعات تولیدشده با این فرایند، نسبت استحکام به وزن بالا میباشد. هیدروفرمینگ لولۀ فشار پایین، یکی از روشهای پیشنهادشده برای حل مشکلات هیدروفرمینگ لوله از قبیل نیاز به فشار بالای سیال و مشکلات آببندی میباشد. روش انجام هیدروفرمینگ فشار پایین لوله، شبیه فشردن جسم جامد است و در آن برخلاف هیدروفرمینگ فشار بالا، قالب بالایی در طول فرایند ثابت نبوده و همزمان با اعمال فشار داخلی به لوله، حرکت کرده و لوله را تحت فشار قرار میدهد. در این مقاله، فرایند هیدروفرمینگ فشار پایین لولههای آلومینیومی AA6063 انجام شده و مقطع گرد لوله بهوسیلۀ فرایند هیدروفرمینگ به مقطع مستطیلی تغییر شکل داده است. همچنین توزیع ضخامت و مقادیر شعاع گوشۀ شکل داده شده، تحت سه مسیر بارگذاری متفاوت بررسی شده است. نتایج نشان میدهد که با افزایش فشار داخلی میتوان به شعاع گوشه کمتری دست پیدا کرد اما نازکشدگی افزایش پیدا میکند. همچنین بیشترین تختی سطح بالایی قطعه، زمانی حاصل میشود که جابجایی قالب بالایی بعد از رسیدن فشار داخلی به مقدار ماکزیمم خود...
- Open Access
- 2 February 2022
- Published by Springer Nature in SN Applied Sciences
- Vol. 4 (3) , 1-11
Experimental study of the effect of temperature and velocity in channel forming of polyvinyl chloride composite reinforced by 3D-fiberglass with an aluminum middle layer
In this paper, the stamp forming process of a U-shaped cross-section channel with sharp corners of composite laminates including aluminum sheet and polyvinyl chloride (PVC) reinforced with 3D-fiberglass was investigated. The laminates were produced by manual layup and arrangement of fibers with different angles of [0°/90°] and [± 45°] degrees using hot press. The process of forming composite samples was carried out at temperatures of 25, 80, 120, 160°C and different velocities of punch. The effect of parameters including layup configuration, temperature, and forming speed on the spring-back of the formed laminates and the required forming force were evaluated. The results showed that as the forming temperature increased, the forming force decreased sharply. The lowest forming force was obtained for the laminate with [± 45°, Al, ± 45°] layout at 160°C temperature which was equal to 0.7KN. Also, with the increase in temperature, the spring-back angle has been reduced, the lowest of which is obtained with the laminate with [0°/90°] 3 layout equal to 8 degrees. Finally, it was concluded that increasing the speed of the forming process results in a decrease in the spring-back angle and this effect is more pronounced at higher temperatures. Graphical abstract
- 2 February 2022
- Published by Springer Nature in SN Applied Sciences
- Vol. 4 (3) , 1-11
Open AccessExperimental study of the effect of temperature and velocity in channel forming of polyvinyl chloride composite reinforced by 3D-fiberglass with an aluminum middle layer
In this paper, the stamp forming process of a U-shaped cross-section channel with sharp corners of composite laminates including aluminum sheet and polyvinyl chloride (PVC) reinforced with 3D-fiberglass was investigated. The laminates were produced by manual layup and arrangement of fibers with different angles of [0°/90°] and [± 45°] degrees using hot press. The process of forming composite samples was carried out at temperatures of 25, 80, 120, 160°C and different velocities of punch. The effect of parameters including layup configuration, temperature, and forming speed on the spring-back of the formed laminates and the required forming force were evaluated. The results showed that as the forming temperature increased, the forming force decreased sharply. The lowest forming force was obtained for the laminate with [± 45°, Al, ± 45°] layout at 160°C temperature which was equal to 0.7KN. Also, with the increase in temperature, the spring-back angle has been reduced, the lowest of which is obtained with the laminate with [0°/90°] 3 layout equal to 8 degrees. Finally, it was concluded that increasing the speed of the forming process results in a decrease in the spring-back angle and this effect is more pronounced at higher temperatures. Graphical abstract
- 21 January 2022
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 16 (1) , 381-388
Minimizing spring-back and thinning in deep drawing process of St14 steel sheets
- 21 January 2022
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 16 (1) , 381-388
Minimizing spring-back and thinning in deep drawing process of St14 steel sheets
- 1 September 2020
- Vol. 13 (3) , 51-57
Influences of Blank Holder Force in The Multi-Step Deep Drawing Process of Aluminum Sheets
- 1 September 2020
- Vol. 13 (3) , 51-57
Influences of Blank Holder Force in The Multi-Step Deep Drawing Process of Aluminum Sheets
- 2 July 2020
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 73 (9) , 2231-2238
Hot Metal Gas Forming of Closed-Cell Aluminum Foam Sandwich Panels
- 2 July 2020
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 73 (9) , 2231-2238
Hot Metal Gas Forming of Closed-Cell Aluminum Foam Sandwich Panels
- Open Access
- 1 April 2019
- Vol. 10 (1) , 125-138
Investigation of hot metal gas forming process of square parts
- 1 April 2019
- Vol. 10 (1) , 125-138
Open AccessInvestigation of hot metal gas forming process of square parts