Jongho Choi
Research Subjects
Jongho Choi has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Chan Kyeong Lee
R&D center, Supercoil co.Ltd, Changwon, Gyeongsangnam-do Korea (the Republic of) 51140
5 shared publications - Minwon Park
Department of Electrical Engineering, Changwon National University, Changwon 51140, Republic of Korea
4 shared publications - Seokho Kim
Changwon National University
4 shared publications - Jeongmin Mun
Department of Mechanical Engineering, Changwon National University, Changwon-si, South Korea
3 shared publications - Quanyue Liu
Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing, China
3 shared publications - Seungyong Hahn
Seoul National University
3 shared publications
Latest Publications
- 13 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Analysis for AC Loss by Electromagnetic Disturbance in HTS Magnet for Maglev Train
Research on Hyper Tube, a Korean high-speed HTS Maglev train, has reached the verification stage for actual operation, and electromagnetic dynamic characteristics analysis of the train is required accordingly. Depending on the winding type of the propulsion armature, the HTS magnet experiences the harmonic that causes AC loss. Beside the static thermal losses by thermal conduction, current leads et al., the AC loss should be take account for the thermal battery design depending on operation conditions. This study describes the AC loss analysis of the HTS magnet induced by the harmonic using the homogeneous T-A formulation widely used in recent. In consideration of acceleration and cruise conditions, the effect of the AC loss by harmonics on the capacity of the solid nitrogen thermal battery was discussed.
- 13 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Analysis for AC Loss by Electromagnetic Disturbance in HTS Magnet for Maglev Train
Research on Hyper Tube, a Korean high-speed HTS Maglev train, has reached the verification stage for actual operation, and electromagnetic dynamic characteristics analysis of the train is required accordingly. Depending on the winding type of the propulsion armature, the HTS magnet experiences the harmonic that causes AC loss. Beside the static thermal losses by thermal conduction, current leads et al., the AC loss should be take account for the thermal battery design depending on operation conditions. This study describes the AC loss analysis of the HTS magnet induced by the harmonic using the homogeneous T-A formulation widely used in recent. In consideration of acceleration and cruise conditions, the effect of the AC loss by harmonics on the capacity of the solid nitrogen thermal battery was discussed.
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Thermal Analysis and In-Field Critical Current Estimation of Conduction-Cooled REBCO Magnet Considering Nonuniform Temperature Distribution
Due to the high upper critical field and transition temperature, REBCO coated conductor show great promise for conduction-cooled magnet applications. The normal zone of high temperature conductor (HTS) spreads slowly, and the conversion of a weak spot into a hot spot is localized and quite fast. Hence, in-field critical current weak spot evaluation under the nonuniform temperature gradient is important for conduction-cooled magnet stability estimation. Cooling path design needs to take the weak spot into account. In this study, a temperature-field-angle dependent critical current estimation neural network was first trained based on a public database of HTS critical current. The equivalent thermal conductivity was applied for the interface contact between the turns. Thermal contact conditions were given to the interface between the coil and bobbin considering actual production situations, such as thermal grease. Combing the non-uniform magnetic field and thermal distribution, the critical current distribution was evaluated to track the weak part. The results of this study will be employed in the design analysis of high magnetic field conduction cooling magnets in the future.
- 8 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Thermal Analysis and In-Field Critical Current Estimation of Conduction-Cooled REBCO Magnet Considering Nonuniform Temperature Distribution
Due to the high upper critical field and transition temperature, REBCO coated conductor show great promise for conduction-cooled magnet applications. The normal zone of high temperature conductor (HTS) spreads slowly, and the conversion of a weak spot into a hot spot is localized and quite fast. Hence, in-field critical current weak spot evaluation under the nonuniform temperature gradient is important for conduction-cooled magnet stability estimation. Cooling path design needs to take the weak spot into account. In this study, a temperature-field-angle dependent critical current estimation neural network was first trained based on a public database of HTS critical current. The equivalent thermal conductivity was applied for the interface contact between the turns. Thermal contact conditions were given to the interface between the coil and bobbin considering actual production situations, such as thermal grease. Combing the non-uniform magnetic field and thermal distribution, the critical current distribution was evaluated to track the weak part. The results of this study will be employed in the design analysis of high magnetic field conduction cooling magnets in the future.
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Analysis of the Experimental Test Results of Laboratory-Scale HTS DC Motor for High-Torque Electric Propulsion
A laboratory-scale direct current (DC) rotating machine with a high-temperature superconducting (HTS) magnets was conceptually designed to obtain 500 W output power under a liquid nitrogen cooling method to verify the operation characteristics of the HTS DC motor. The experimental test results of the HTS motor for high-torque electric propulsion are analyzed and presented in this paper. The two HTS magnets were fabricated and assembled using a dynamo system to demonstrate the operation. The excitation current for the two HTS magnets connected in series was kept within 0–40 A using the DC power supplier. The rotational speed of the motor could be kept at 100–600 rpm, and the torque was measured during real-time operation. These test results can be used to design a large HTS DC rotating machine for an electric propulsion system.
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Analysis of the Experimental Test Results of Laboratory-Scale HTS DC Motor for High-Torque Electric Propulsion
A laboratory-scale direct current (DC) rotating machine with a high-temperature superconducting (HTS) magnets was conceptually designed to obtain 500 W output power under a liquid nitrogen cooling method to verify the operation characteristics of the HTS DC motor. The experimental test results of the HTS motor for high-torque electric propulsion are analyzed and presented in this paper. The two HTS magnets were fabricated and assembled using a dynamo system to demonstrate the operation. The excitation current for the two HTS magnets connected in series was kept within 0–40 A using the DC power supplier. The rotational speed of the motor could be kept at 100–600 rpm, and the torque was measured during real-time operation. These test results can be used to design a large HTS DC rotating machine for an electric propulsion system.
- 28 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-6
Thermal Analysis of Leakage Currents of No-Insulation HTS Racetrack Coils Using a Three-Dimensional Turn-Distributed Equivalent Circuit FEA Model
In promoting novel products with superconducting magnets to transportation and science industries, the most important factor is reliability. Recently, it was reported that a no-insulation (NI) superconducting magnet could be damaged with quenches caused by a thermal runaway, significant temperature deviation, extremely high characteristic resistance, etc. To resolve this issue, numerical analysis of high-temperature superconducting (HTS) racetrack coils with NI winding technology should be conducted. The authors proposed a homogenization method to analyze operating characteristics of the NI HTS coils by simplifying the finite element analysis (FEA) model and decreasing the solution time. In order to estimate their thermal stabilities, the proposed FEA simulation is one of the efficient methods for solving the electrical and thermal factors simultaneously. In this paper, the thermal analysis of the leakage currents of NI HTS racetrack coils is presented using a three-dimensional (3D) turn-distributed equivalent circuit FEA model. The charging and discharging delay phenomena were modeled by considering the contact resistances by turns. With the equivalent circuit model of the NI HTS magnets, the 3D racetrack coils were designed by considering a single turn and stacked turns, including metal insulation layers. Their material properties according to temperature variation were applied in the transient analysis. The critical currents by turns were estimated by considering the magnetic field, its angle, and temperature with a given current simultaneously. The simulation results were compared with a fabricated NI HTS magnet and are presented in this paper.
- 28 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-6
Thermal Analysis of Leakage Currents of No-Insulation HTS Racetrack Coils Using a Three-Dimensional Turn-Distributed Equivalent Circuit FEA Model
In promoting novel products with superconducting magnets to transportation and science industries, the most important factor is reliability. Recently, it was reported that a no-insulation (NI) superconducting magnet could be damaged with quenches caused by a thermal runaway, significant temperature deviation, extremely high characteristic resistance, etc. To resolve this issue, numerical analysis of high-temperature superconducting (HTS) racetrack coils with NI winding technology should be conducted. The authors proposed a homogenization method to analyze operating characteristics of the NI HTS coils by simplifying the finite element analysis (FEA) model and decreasing the solution time. In order to estimate their thermal stabilities, the proposed FEA simulation is one of the efficient methods for solving the electrical and thermal factors simultaneously. In this paper, the thermal analysis of the leakage currents of NI HTS racetrack coils is presented using a three-dimensional (3D) turn-distributed equivalent circuit FEA model. The charging and discharging delay phenomena were modeled by considering the contact resistances by turns. With the equivalent circuit model of the NI HTS magnets, the 3D racetrack coils were designed by considering a single turn and stacked turns, including metal insulation layers. Their material properties according to temperature variation were applied in the transient analysis. The critical currents by turns were estimated by considering the magnetic field, its angle, and temperature with a given current simultaneously. The simulation results were compared with a fabricated NI HTS magnet and are presented in this paper.
- 2 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-7
Thermal Design of the Conduction-Cooled High Temperature Superconducting Magnet for Pulsating Magnetic Field
A conduction-cooled high temperature superconducting (HTS) solenoid is fabricated to produce pulsating 4 T magnetic field for magnetic refrigeration. HTS conductor of 245 m is wound as a solenoid with 112 layers each of which consists of 12 turns of the conductor. For a stable ramping operation of the magnet, AC loss inside the winding pack should be effectively rejected to the heat sink. The thermal drains are inserted between the layers and connected to the magnet flange which is cooled by a commercial two-stage Gifford-McMahon cooler. They are made of Oxygen-Free High Conductivity (OFHC) copper, and has a width of 6 mm and a thickness of 50 ${\rm{\mu }}$ m. Thermal analysis is conducted to confirm the effect of the thermal drain on the AC loss heat rejection. AC loss of the magnet is estimated by using T-A formulation (current vector potential T and magnetic vector potential A). The ramp rate of the magnet and the heat sink temperature are set to 0.1 T/s and 4.5 K, respectively. In the thermal diffusion calculation, each winding layer is considered as the lumped capacitance. In addition, thermal conduction between the adjacent layers and that through the thermal drains are considered. The thermal analysis confirms that the conductor temperature of the winding is maintained lower than the operating limit of 20 K. Based on the results of the thermal analysis, the stable pulsating operation of the conduction-cooled superconducting magnet is predicted to be feasible and is also confirmed by the experiment.
- 2 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-7
Thermal Design of the Conduction-Cooled High Temperature Superconducting Magnet for Pulsating Magnetic Field
A conduction-cooled high temperature superconducting (HTS) solenoid is fabricated to produce pulsating 4 T magnetic field for magnetic refrigeration. HTS conductor of 245 m is wound as a solenoid with 112 layers each of which consists of 12 turns of the conductor. For a stable ramping operation of the magnet, AC loss inside the winding pack should be effectively rejected to the heat sink. The thermal drains are inserted between the layers and connected to the magnet flange which is cooled by a commercial two-stage Gifford-McMahon cooler. They are made of Oxygen-Free High Conductivity (OFHC) copper, and has a width of 6 mm and a thickness of 50 ${\rm{\mu }}$ m. Thermal analysis is conducted to confirm the effect of the thermal drain on the AC loss heat rejection. AC loss of the magnet is estimated by using T-A formulation (current vector potential T and magnetic vector potential A). The ramp rate of the magnet and the heat sink temperature are set to 0.1 T/s and 4.5 K, respectively. In the thermal diffusion calculation, each winding layer is considered as the lumped capacitance. In addition, thermal conduction between the adjacent layers and that through the thermal drains are considered. The thermal analysis confirms that the conductor temperature of the winding is maintained lower than the operating limit of 20 K. Based on the results of the thermal analysis, the stable pulsating operation of the conduction-cooled superconducting magnet is predicted to be feasible and is also confirmed by the experiment.
- 14 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-5
Development of a 1.2 MW Superconducting Induction Heater Using MgB2 NI Magnets
In industry, there are many issues with the implementation of conventional heating furnaces. Specially, there issues include environmental protection policies put in place by governments and old and inefficient technologies for heating metals. Additionally, work spaces can be large, dirty, dangerous, and dull. As a possible solution to these issues, a superconducting induction heater (SIH) with high efficiency was developed using MgB2 magnet manufacturing technologies. This paper introduces and discusses the development of a 1.2 MW SIH using MgB2 NI magnets. The target magnetic flux density of the magnets with iron cores for 1,200 kW SIH was determined to achieve a high heating capacity for heating iron billets. The simulation results for the magnets were analyzed using finite element method (FEM) modeling. The experimental tests and results are presented in detail. The largest MgB2 magnets in the world were fabricated and tested and demonstrated outstanding operational results. These testing processes will be helpful for the heating characteristics analysis of various MgB2 magnets for commercialization.
- 14 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (6) , 1-5
Development of a 1.2 MW Superconducting Induction Heater Using MgB2 NI Magnets
In industry, there are many issues with the implementation of conventional heating furnaces. Specially, there issues include environmental protection policies put in place by governments and old and inefficient technologies for heating metals. Additionally, work spaces can be large, dirty, dangerous, and dull. As a possible solution to these issues, a superconducting induction heater (SIH) with high efficiency was developed using MgB2 magnet manufacturing technologies. This paper introduces and discusses the development of a 1.2 MW SIH using MgB2 NI magnets. The target magnetic flux density of the magnets with iron cores for 1,200 kW SIH was determined to achieve a high heating capacity for heating iron billets. The simulation results for the magnets were analyzed using finite element method (FEM) modeling. The experimental tests and results are presented in detail. The largest MgB2 magnets in the world were fabricated and tested and demonstrated outstanding operational results. These testing processes will be helpful for the heating characteristics analysis of various MgB2 magnets for commercialization.
- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Design and Performance Analysis Results of Iron-Core Type MgB2 and HTS Magnets for Large-Scale Superconducting Induction Heaters
Conventional induction heaters that have a large capacity to preheat metal billets for the extrusion and forging of products, such as copper, titanium, carbon, and stainless steels, have low energy efficiency (below 60%) due to considerable losses from the copper coils. The MAGHEET, a preheating machine for the extrusion and forging plants as called a superconducting induc-tion heater (SIH), is one of several efforts that aim to improve their efficiency. Supercoil Co., Ltd. has developed two types of superconducting magnets for large-scale SIH: MgB2 magnets and HTS magnets. In this paper, we introduce the design specifications and performance analysis results of these two types of superconducting magnets under the same conduction cooling conditions. The cooling and excitation characteristics of the two superconducting magnets at near 10 K are presented and compared. The first commercial MAGHEET is also introduced.
- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Design and Performance Analysis Results of Iron-Core Type MgB2 and HTS Magnets for Large-Scale Superconducting Induction Heaters
Conventional induction heaters that have a large capacity to preheat metal billets for the extrusion and forging of products, such as copper, titanium, carbon, and stainless steels, have low energy efficiency (below 60%) due to considerable losses from the copper coils. The MAGHEET, a preheating machine for the extrusion and forging plants as called a superconducting induc-tion heater (SIH), is one of several efforts that aim to improve their efficiency. Supercoil Co., Ltd. has developed two types of superconducting magnets for large-scale SIH: MgB2 magnets and HTS magnets. In this paper, we introduce the design specifications and performance analysis results of these two types of superconducting magnets under the same conduction cooling conditions. The cooling and excitation characteristics of the two superconducting magnets at near 10 K are presented and compared. The first commercial MAGHEET is also introduced.
- 22 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Practical Design and Experimental Test of MgB2 Magnets for 300 kW-Class Superconducting Induction Heater
A shape and characteristics of Superconducting magnets used in superconducting applications are effected by purposing of a device and these coils are wound with various superconducting wires such as high temperature superconducting (HTS) wire and low temperature superconducting (LTS) wire. MgB 2 wire is the one of the wires which can compensate the disadvantages of each wire. Therefore, if we adopt MgB 2 wire to superconducting applications, we get advantages such as operating temperature with cryogen free cooling system and wire's price. In this paper, the author designs, fabricates and tests MgB 2 magnet for a 300 kW-class DC superconducting induction heater. Firstly, MgB 2 magnet is designed and analyzed using finite elements method for a 300 kW-class superconducting induction heater. Secondly, the magnet is fabricated using dry-winding and metal insulation method. Finally, MgB 2 magnet is stacked and assembled into conduction cooling property measurement system for evaluate its performance and characteristics. As a result, MgB 2 magnet guaranties a satisfactory performance with low price and highest critical temperature among LTS wires. The low temperature as 10 K, which is the operating temperature of the MgB 2 magnet, can be achieved by a conduction cooling system. This study will be effectively utilized for a 300 kW-class superconducting induction heater and other superconducting magnet applications.
- 22 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Practical Design and Experimental Test of MgB2 Magnets for 300 kW-Class Superconducting Induction Heater
A shape and characteristics of Superconducting magnets used in superconducting applications are effected by purposing of a device and these coils are wound with various superconducting wires such as high temperature superconducting (HTS) wire and low temperature superconducting (LTS) wire. MgB 2 wire is the one of the wires which can compensate the disadvantages of each wire. Therefore, if we adopt MgB 2 wire to superconducting applications, we get advantages such as operating temperature with cryogen free cooling system and wire's price. In this paper, the author designs, fabricates and tests MgB 2 magnet for a 300 kW-class DC superconducting induction heater. Firstly, MgB 2 magnet is designed and analyzed using finite elements method for a 300 kW-class superconducting induction heater. Secondly, the magnet is fabricated using dry-winding and metal insulation method. Finally, MgB 2 magnet is stacked and assembled into conduction cooling property measurement system for evaluate its performance and characteristics. As a result, MgB 2 magnet guaranties a satisfactory performance with low price and highest critical temperature among LTS wires. The low temperature as 10 K, which is the operating temperature of the MgB 2 magnet, can be achieved by a conduction cooling system. This study will be effectively utilized for a 300 kW-class superconducting induction heater and other superconducting magnet applications.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-7
Economic Evaluation of 23 kV Tri-Axial HTS Cable Application to Power System
Research on the development of a superconducting power cable for commercialization is currently underway across the world. Many demonstrations of superconducting power cables connected to real power grids have already been conducted with various designs depending on the voltage levels of the distribution and transmission lines. In Korea, the first commercial project for high temperature superconducting (HTS) power cables, “Shingal Project” which is fully funded by Korea Electric Power Corporation (KEPCO), is underway to connect two substations with a 23 kV HTS cable with a distance of 1 km. In addition, the KEPCO Research Center (KEPRI) initiated the project in 2017 to develop the 23-kV tri-axial HTS power cables, including a cooling system, for a distance of 3 km. In this paper, the recent progress and research activities related to the two 23-kV superconducting power cables projects are discussed. An economic evaluation of the HTS power cables for commercialization in consideration of their construction environments and social issues is also presented.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-7
Economic Evaluation of 23 kV Tri-Axial HTS Cable Application to Power System
Research on the development of a superconducting power cable for commercialization is currently underway across the world. Many demonstrations of superconducting power cables connected to real power grids have already been conducted with various designs depending on the voltage levels of the distribution and transmission lines. In Korea, the first commercial project for high temperature superconducting (HTS) power cables, “Shingal Project” which is fully funded by Korea Electric Power Corporation (KEPCO), is underway to connect two substations with a 23 kV HTS cable with a distance of 1 km. In addition, the KEPCO Research Center (KEPRI) initiated the project in 2017 to develop the 23-kV tri-axial HTS power cables, including a cooling system, for a distance of 3 km. In this paper, the recent progress and research activities related to the two 23-kV superconducting power cables projects are discussed. An economic evaluation of the HTS power cables for commercialization in consideration of their construction environments and social issues is also presented.
- 11 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
A Design Study on a Multibillet HTS Induction Heater With REBCO Racetrack Coils
Recently an induction heating system comprising a pair of no-insulation high temperature superconductor (HTS) racetrack coils was built and now it is commercially available. It generates a direct-current (DC) magnetic field in which a conductive metallic billet rotates at a high speed. Most DC induction machines accommodate a “single” billet per operation. This paper proposes an alternative concept of a “multiple-billet” induction heater, where the multiple billets can be simultaneously heated. The system consists of 8 pairs of HTS racetrack coils that are placed in a circular pattern. An arbitrary number of billets may be placed and rotate at the same time in the space between racetrack coil pairs. The main goal in this paper is to theoretically demonstrate the principle of operation of the new multi-billet system. The paper presents: (1) overall system configuration and the principle of operation; (2) electromagnetic design of the 8-pole HTS magnet; (3) analyses with key operation parameters to estimate the multi-billet heater performance. Due to the “positive” mutual inductance among neighbor racetrack coils, the multi-billet system is estimated to deliver a larger heating power per billet than that of its single-billet counterpart for given operating conditions. Also, due to the eddy-currents induced in each billet, the power per billet reduces when the number of billets increases beyond an optimal value.
- 11 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 29 (5) , 1-5
A Design Study on a Multibillet HTS Induction Heater With REBCO Racetrack Coils
Recently an induction heating system comprising a pair of no-insulation high temperature superconductor (HTS) racetrack coils was built and now it is commercially available. It generates a direct-current (DC) magnetic field in which a conductive metallic billet rotates at a high speed. Most DC induction machines accommodate a “single” billet per operation. This paper proposes an alternative concept of a “multiple-billet” induction heater, where the multiple billets can be simultaneously heated. The system consists of 8 pairs of HTS racetrack coils that are placed in a circular pattern. An arbitrary number of billets may be placed and rotate at the same time in the space between racetrack coil pairs. The main goal in this paper is to theoretically demonstrate the principle of operation of the new multi-billet system. The paper presents: (1) overall system configuration and the principle of operation; (2) electromagnetic design of the 8-pole HTS magnet; (3) analyses with key operation parameters to estimate the multi-billet heater performance. Due to the “positive” mutual inductance among neighbor racetrack coils, the multi-billet system is estimated to deliver a larger heating power per billet than that of its single-billet counterpart for given operating conditions. Also, due to the eddy-currents induced in each billet, the power per billet reduces when the number of billets increases beyond an optimal value.