Bingqi Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bingqi Yu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Tangdai Xia
Research Center of Coastal and Urban Geotechnical Engineering, Zhejiang University, Hangzhou 310058, China
2 shared publications - Bowen Kong
School of Civil Engineering and Architecture, Zhejiang University of Science and Technology, No. 318 Liuhe Road, Xihu District, Hangzhou 310023, China
1 shared publication - Chen-Xiang Dai
Research Center of Coastal and Urban Geotechnical Engineering, Zhejiang University, Hangzhou 310058, China
1 shared publication - Fan Xia
Research Center of Coastal and Urban Geotechnical Engineering, College of Architecture and Civil Engineering, Zhejiang University, Hangzhou 310015, China
1 shared publication - Longju Zhang
College of Water Conservancy and Architectural Engineering, University of Tarim, Alar 843300, China
1 shared publication - Xingang Wang
Faculty of Water Resources and Architectural Engineering, Tarim University, Alar 843300, China
1 shared publication
Latest Publications
- Open Access
- 2 April 2021
- Published by MDPI AG in ISPRS International Journal of Geo-Information
- Vol. 10 (4) , 221
Deformation Characteristics of Tianjiaba Landslide Induced by Surcharge
The Tianjiaba landslide on the Hang Rui expressway was located in the south of Sinan County, Tongren City, Guizhou Province. From the night of 2 July to the morning of 3 July 2011, numerous house cracks, foundation subsidence, and surface cracks suddenly occurred in the Tudiwan and Tianjiaba villages on the north and south sides of the management area. Based on the field geological survey, drilling, pit exploration, surface displacement, fracture observation, and deep displacement monitoring data analysis the deformation characteristics and causes of the Tianjiaba landslide were comprehensively analyzed. In this study, the landslide was divided into three areas, in which fracture group 3 was the most severe. Among the ten inclinometer holes, the sliding surface displacement of No.8 inclinometer hole was the largest, i.e., 25 mm. The sliding surface slopes of fracture groups 1, 2, and 3 were small, i.e., 12.25°, 4.97° and 6.62° to 4.64°, respectively. The results showed that the displacement values of different positions of the landslide were different, and the ground displacement value was larger than the sliding surface displacement value. The maximum displacement of the ground was 242.68 mm, which is larger than the maximum displacement of the inclinometer hole. Because the displacement of the upper part was greater than that of the lower part, bulging cracks formed in the lower part of the landslide. When the displacement of the upper part was less than that of the lower part, tension cracks formed in the lower part of the landslide. According to the surface cracks and displacement values of inclinometer holes on the sliding surface, the landslide was in the initial sliding stage and filling the platform of the management area on the hillside was the main cause of the landslide.
- 2 April 2021
- Published by MDPI AG in ISPRS International Journal of Geo-Information
- Vol. 10 (4) , 221
Open AccessDeformation Characteristics of Tianjiaba Landslide Induced by Surcharge
The Tianjiaba landslide on the Hang Rui expressway was located in the south of Sinan County, Tongren City, Guizhou Province. From the night of 2 July to the morning of 3 July 2011, numerous house cracks, foundation subsidence, and surface cracks suddenly occurred in the Tudiwan and Tianjiaba villages on the north and south sides of the management area. Based on the field geological survey, drilling, pit exploration, surface displacement, fracture observation, and deep displacement monitoring data analysis the deformation characteristics and causes of the Tianjiaba landslide were comprehensively analyzed. In this study, the landslide was divided into three areas, in which fracture group 3 was the most severe. Among the ten inclinometer holes, the sliding surface displacement of No.8 inclinometer hole was the largest, i.e., 25 mm. The sliding surface slopes of fracture groups 1, 2, and 3 were small, i.e., 12.25°, 4.97° and 6.62° to 4.64°, respectively. The results showed that the displacement values of different positions of the landslide were different, and the ground displacement value was larger than the sliding surface displacement value. The maximum displacement of the ground was 242.68 mm, which is larger than the maximum displacement of the inclinometer hole. Because the displacement of the upper part was greater than that of the lower part, bulging cracks formed in the lower part of the landslide. When the displacement of the upper part was less than that of the lower part, tension cracks formed in the lower part of the landslide. According to the surface cracks and displacement values of inclinometer holes on the sliding surface, the landslide was in the initial sliding stage and filling the platform of the management area on the hillside was the main cause of the landslide.
- Open Access
- 4 March 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (3) , 170
Pore Size Changes in Marine Soft Soil under Various Freezing Conditions
Artificial freezing methods can help highlight the mechanical properties of marine clay. The construction of cross passages in metro tunnels employs the freezing method. Freeze–thaw circulation, which is part of the process, affects the engineering properties of clay and produces differential settling. This paper describes the percentages of specific diameters of frozen–thawed soil under different freezing temperatures, measured with the help of nuclear magnetic resonance (NMR). In response to the experimental results, a weakening effect of freezing temperature and speed on soft soil is proposed. All sizes of undisturbed soil pores tend to increase under various freezing temperatures. Owing to differences in free water content, the water in medium pores freezes quicker than that in tiny pores. The quicker the freezing, the greater the resulting void ratio. Finally, potential reasons for changes in pore size under different freezing conditions are explained from a microcosmic perspective.
- 4 March 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (3) , 170
Open AccessPore Size Changes in Marine Soft Soil under Various Freezing Conditions
Artificial freezing methods can help highlight the mechanical properties of marine clay. The construction of cross passages in metro tunnels employs the freezing method. Freeze–thaw circulation, which is part of the process, affects the engineering properties of clay and produces differential settling. This paper describes the percentages of specific diameters of frozen–thawed soil under different freezing temperatures, measured with the help of nuclear magnetic resonance (NMR). In response to the experimental results, a weakening effect of freezing temperature and speed on soft soil is proposed. All sizes of undisturbed soil pores tend to increase under various freezing temperatures. Owing to differences in free water content, the water in medium pores freezes quicker than that in tiny pores. The quicker the freezing, the greater the resulting void ratio. Finally, potential reasons for changes in pore size under different freezing conditions are explained from a microcosmic perspective.