Hikaru Souda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hikaru Souda has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
Akira Nagashima
Kansai Photon Science Institute, Japan Atomic Energy Agency, 8-1 Umemidai, Kizugawa, Kyoto 619-0215, Japan
2 shared publications- Akira Noda
Institute for Chemical Research, Kyoto University, Gokasho, Uji, Kyoto 611-0011, Japan
2 shared publications Akito Sagisaka
Kansai Photon Science Institute, Japan Atomic Energy Agency, 8-1 Umemidai, Kizugawa, Kyoto 619-0215, Japan
2 shared publicationsAtsushi Fukumi
National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage-ku, Chiba 263-8555, Japan
2 shared publicationsHiromu Tongu
Institute for Chemical Research, Kyoto University, Gokasho, Uji, Kyoto 611-0011, Japan
2 shared publications- Hiroyuki Daido
Institute of Laser Engineering, The University of Osaka 1 , 2-6 Yamada-oka, Suita, Osaka 565-0871
2 shared publications
Latest Publications
- Open Access
- 1 September 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (9)
Demonstration and real-time non-destructive diagnosis of a high-flux laser-driven proton bunch
To realize a compact and high-intensity ion beam facility based on laser-driven ion acceleration by Target Normal Sheath Acceleration, we constructed a dedicated beamline capable of transporting and controlling proton beams with kinetic energy of 1.5 MeV. The system consists of a quadrupole triplet electromagnet for spatial focusing and an energy-compressing cavity (ECC) for longitudinal phase rotation, enabling momentum compression. A wall current monitor (WCM), installed 4.2 m downstream of the source, enables real-time, non-destructive bunch diagnostics. Using this setup, a single-bunch proton with a kinetic energy of 1.5 MeV was generated from a 5.0 μm-thick nickel tape target and compressed by phase rotation in the ECC. The time-domain standard deviation of the bunch length, as measured by the WCM, was found to be less than σBunch≃ 0.14 ns (limited by the measurement resolution), and the bunch was transversely focused to a root-mean-square diameter of ∼10 mm at the WCM position, as determined from beam transport simulations. The single-shot irradiation fluence exceeded 5.5 × 107 (protons/cm2)/bunch with an energy spread of 4.6%, corresponding to a peak flux of ∼1017 (protons/cm2)/s. Such a low-energy, sub-nanosecond, high-flux single-bunch proton beam is extremely difficult to achieve with conventional ion accelerator systems. It enables experimental investigation of fundamental material damage processes with high temporal resolution, including early stage defect formation and atomic displacements. This laser-driven ions beam study is expected to significantly advance time-resolved applications requiring sub-nanosecond temporal resolution, particularly in the fields of advanced materials research.
- 1 September 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (9)
Open AccessDemonstration and real-time non-destructive diagnosis of a high-flux laser-driven proton bunch
To realize a compact and high-intensity ion beam facility based on laser-driven ion acceleration by Target Normal Sheath Acceleration, we constructed a dedicated beamline capable of transporting and controlling proton beams with kinetic energy of 1.5 MeV. The system consists of a quadrupole triplet electromagnet for spatial focusing and an energy-compressing cavity (ECC) for longitudinal phase rotation, enabling momentum compression. A wall current monitor (WCM), installed 4.2 m downstream of the source, enables real-time, non-destructive bunch diagnostics. Using this setup, a single-bunch proton with a kinetic energy of 1.5 MeV was generated from a 5.0 μm-thick nickel tape target and compressed by phase rotation in the ECC. The time-domain standard deviation of the bunch length, as measured by the WCM, was found to be less than σBunch≃ 0.14 ns (limited by the measurement resolution), and the bunch was transversely focused to a root-mean-square diameter of ∼10 mm at the WCM position, as determined from beam transport simulations. The single-shot irradiation fluence exceeded 5.5 × 107 (protons/cm2)/bunch with an energy spread of 4.6%, corresponding to a peak flux of ∼1017 (protons/cm2)/s. Such a low-energy, sub-nanosecond, high-flux single-bunch proton beam is extremely difficult to achieve with conventional ion accelerator systems. It enables experimental investigation of fundamental material damage processes with high temporal resolution, including early stage defect formation and atomic displacements. This laser-driven ions beam study is expected to significantly advance time-resolved applications requiring sub-nanosecond temporal resolution, particularly in the fields of advanced materials research.
- 1 April 2020
- Published by Elsevier in Radiation Measurements
- Vol. 133
Scintillator screen for measuring low-dose halo in scanning carbon-ion therapy
- 1 April 2020
- Published by Elsevier in Radiation Measurements
- Vol. 133
Scintillator screen for measuring low-dose halo in scanning carbon-ion therapy
- 20 July 2007
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 46 (8L) , L717
High-Quality Laser-Produced Proton Beam Realized by the Application of a Synchronous RF Electric Field
- 20 July 2007
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 46 (8L) , L717
High-Quality Laser-Produced Proton Beam Realized by the Application of a Synchronous RF Electric Field
- 6 March 2006
- Published by Cambridge University Press (CUP) in Laser and Particle Beams
- Vol. 24 (1) , 117-123
Observation of strongly collimated proton beam from Tantalum targets irradiated with circular polarized laser pulses
High-energy protons are generated by focusing an ultrashort pulsed high intensity laser at the Advanced Photon Research Center, JAERI-Kansai onto thin (thickness <10 μm) Tantalum targets. The laser intensities are about 4 × 1018 W/cm2. The prepulse level of the laser pulse is measured with combination of a PIN photo diode and a cross correlator and is less than 10−6. A quarter-wave plate is installed into the laser beam line to create circularly polarized pulses. Collimated high energy protons are observed with CH coated Tantalum targets irradiated with the circularly polarized laser pulses. The beam divergence of the generated proton beam is measured with a CR-39 track detector and is about 6 mrad.
- 6 March 2006
- Published by Cambridge University Press (CUP) in Laser and Particle Beams
- Vol. 24 (1) , 117-123
Observation of strongly collimated proton beam from Tantalum targets irradiated with circular polarized laser pulses
High-energy protons are generated by focusing an ultrashort pulsed high intensity laser at the Advanced Photon Research Center, JAERI-Kansai onto thin (thickness <10 μm) Tantalum targets. The laser intensities are about 4 × 1018 W/cm2. The prepulse level of the laser pulse is measured with combination of a PIN photo diode and a cross correlator and is less than 10−6. A quarter-wave plate is installed into the laser beam line to create circularly polarized pulses. Collimated high energy protons are observed with CH coated Tantalum targets irradiated with the circularly polarized laser pulses. The beam divergence of the generated proton beam is measured with a CR-39 track detector and is about 6 mrad.