Yanxia Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yanxia Wu has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
Shengwang Yu
11 shared publicationsYing Liu
11 shared publications- Ying Liu
College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China
9 shared publications Ke Li
6 shared publications- Shengwang Yu
College of Materials Science and Engineering, Taiyuan University of Technology, 209 Daxue Street, Yuci District, Jinzhong 030600, China
6 shared publications Bang Shi
5 shared publications
Latest Publications
- Open Access
- 23 April 2026
- Published by Elsevier in SSRN Electronic Journal
Low-Temperature Magnetron Co-Sputtering of Cr-Al-C Films: Formation of Cr2AlC MAX Phase and Its Influence on Corrosion and Tribological Performance
The Cr2AlC MAX phase was successfully prepared by co-sputtering Cr-Al alloy target and graphite target at low temperature by magnetron sputtering method. Deposition temperature (100-400 °C) was investigated, examining its effects on MAX phase formation, film structure, corrosion resistance, and friction properties. The results indicated that when the deposition temperature reached 300 °C, the Cr2AlC MAX phase began to form in the film, and its crystallization tendency became more pronounced with further increasing temperature. At the same time, the sp²C content in the film first decreased and then increased, the residual stress first increased and then decreased, and the adhesion strength to the substrate first decreased and then increased. The formation of the Cr2AlC MAX phase and inert CrxCy phases helped suppress the penetration of corrosive ions, hinder the diffusion of corrosive media, and enhance the shielding effect and passivation stability of the coating surface; however, excessive residual stress significantly weakened the corrosion resistance of the film. Notably, the S4 film exhibited the best corrosion resistance owing to its optimal sp3C content, lowest residual stress, high coating-substrate adhesion, low surface roughness, highest Al doping content, and lowest coating porosity. Tribological test results indicated that the formation of the Cr2AlC MAX phase significantly improved the tribological performance of the coating in air; however, in 3.5 wt.% NaCl solution, mechanical wear remained the dominant wear mechanism, while the influence of corrosion on tribological behavior was relatively limited.
- 23 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessLow-Temperature Magnetron Co-Sputtering of Cr-Al-C Films: Formation of Cr2AlC MAX Phase and Its Influence on Corrosion and Tribological Performance
The Cr2AlC MAX phase was successfully prepared by co-sputtering Cr-Al alloy target and graphite target at low temperature by magnetron sputtering method. Deposition temperature (100-400 °C) was investigated, examining its effects on MAX phase formation, film structure, corrosion resistance, and friction properties. The results indicated that when the deposition temperature reached 300 °C, the Cr2AlC MAX phase began to form in the film, and its crystallization tendency became more pronounced with further increasing temperature. At the same time, the sp²C content in the film first decreased and then increased, the residual stress first increased and then decreased, and the adhesion strength to the substrate first decreased and then increased. The formation of the Cr2AlC MAX phase and inert CrxCy phases helped suppress the penetration of corrosive ions, hinder the diffusion of corrosive media, and enhance the shielding effect and passivation stability of the coating surface; however, excessive residual stress significantly weakened the corrosion resistance of the film. Notably, the S4 film exhibited the best corrosion resistance owing to its optimal sp3C content, lowest residual stress, high coating-substrate adhesion, low surface roughness, highest Al doping content, and lowest coating porosity. Tribological test results indicated that the formation of the Cr2AlC MAX phase significantly improved the tribological performance of the coating in air; however, in 3.5 wt.% NaCl solution, mechanical wear remained the dominant wear mechanism, while the influence of corrosion on tribological behavior was relatively limited.
- 3 February 2026
- Published by Elsevier in Materials Today Physics
- Vol. 61
Heterogeneous Fe/Ti3C2Tx MXene derived magnetic-dielectric synergy for efficient microwave attenuation at ultrathin thickness
- 3 February 2026
- Published by Elsevier in Materials Today Physics
- Vol. 61
Heterogeneous Fe/Ti3C2Tx MXene derived magnetic-dielectric synergy for efficient microwave attenuation at ultrathin thickness
- 11 June 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 145, 644-652
Modulation of Ni3Se2/NiSe electronic structure by Mo doping for efficient simultaneous H2 and formate production
- 11 June 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 145, 644-652
Modulation of Ni3Se2/NiSe electronic structure by Mo doping for efficient simultaneous H2 and formate production
- 5 November 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 919
Enhancement of strength-ductility synergy of in situ synthesized graphene/Ni composite via Mo microalloying
- 5 November 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 919
Enhancement of strength-ductility synergy of in situ synthesized graphene/Ni composite via Mo microalloying
- 1 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24  (16) , 25581-25589
Preparation and Deep-UV Solar-Blind Photovoltaic Performance of AlYN-Based MSM Detector
Based on the benefits of AlN solar-blind ultraviolet (SUBV) detectors in the field of photovoltaics, rare earth element yttrium (Y) was doped and investigated to regulate the sensitization range of AlN films by dual-target co-sputtering with different Y target sputtering power. The results showed that the structure of the film changed from AlN (002) to mixture of AlYN (002) and (100) then to amorphous with increased Y content, accompanied with the transformation from pebble-like shape morphology to amorphous morphology. The adjusted band gap (5.65-4.51 eV) of AlYN films was widened by Y doped, notably, the film S4 (with Y content of 8.1 at.%) completely covered the solar-blind response band. Specially, there were AlYN and Y crystals formed in the film S2 (with Y content of 1.28 at.%) with low resistivity and high carrier mobility. Based on which, metal-semiconductor-metal (MSM) type photodetectors (PDs) with Ag/Al/AlYN MSM IDE structures were fabricated, in which the film S2 exhibited the best photo-detection characteristics at -2 V bias, with photo-to-dark current ratio ( PDCR ), responsivity ( R ), external quantum efficiency ( EQE ), and specific detectivity ( D *) of 154.9, 35.7 μA/W, 2.27 × 10 -2 % and 1.42 × 10 10 Jones, respectively, while possessing significant self-powered characteristics ( PDCR was 121.5).
- 1 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24  (16) , 25581-25589
Preparation and Deep-UV Solar-Blind Photovoltaic Performance of AlYN-Based MSM Detector
Based on the benefits of AlN solar-blind ultraviolet (SUBV) detectors in the field of photovoltaics, rare earth element yttrium (Y) was doped and investigated to regulate the sensitization range of AlN films by dual-target co-sputtering with different Y target sputtering power. The results showed that the structure of the film changed from AlN (002) to mixture of AlYN (002) and (100) then to amorphous with increased Y content, accompanied with the transformation from pebble-like shape morphology to amorphous morphology. The adjusted band gap (5.65-4.51 eV) of AlYN films was widened by Y doped, notably, the film S4 (with Y content of 8.1 at.%) completely covered the solar-blind response band. Specially, there were AlYN and Y crystals formed in the film S2 (with Y content of 1.28 at.%) with low resistivity and high carrier mobility. Based on which, metal-semiconductor-metal (MSM) type photodetectors (PDs) with Ag/Al/AlYN MSM IDE structures were fabricated, in which the film S2 exhibited the best photo-detection characteristics at -2 V bias, with photo-to-dark current ratio ( PDCR ), responsivity ( R ), external quantum efficiency ( EQE ), and specific detectivity ( D *) of 154.9, 35.7 μA/W, 2.27 × 10 -2 % and 1.42 × 10 10 Jones, respectively, while possessing significant self-powered characteristics ( PDCR was 121.5).
- Open Access
- 15 February 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42  (2)
Preparation and tribological properties of Ni/DLC multilayer film
Ni was selected as a transition layer and sublayer in the diamondlike carbon-based multilayered film with varied bilayer periods (from 228 to 970 nm) prepared by magnetron sputtering. The reaction between Ni- and C-containing particles was discussed, and the influences of bilayer periods on the structure and morphology, accompanied with the frictional behaviors at different loading forces (2 and 5 N), as well as the field emission properties were investigated. The results showed that Ni grew in the (111) plane, and there was no Ni–C bond or graphene formed in the film because of the relatively lower energy during deposition. Moreover, the content of sp2C in the film, the hardness, and the field emission performance exhibited an initial increase followed by a subsequent decrease with increasing bilayer periods. However, the frictional coefficient decreased owing to more graphitization with an increase of the applied load. Particularly noteworthy was that the film possessed a bilayer period of 710 nm, displayed a compact structure with a smaller grain size, and showed reduced sp2C content in the role of Ni. This resulted in sustained lower surface roughness, heightened hardness, decreased coefficient of friction, and a smaller opening electric field.
- 15 February 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42  (2)
Open AccessPreparation and tribological properties of Ni/DLC multilayer film
Ni was selected as a transition layer and sublayer in the diamondlike carbon-based multilayered film with varied bilayer periods (from 228 to 970 nm) prepared by magnetron sputtering. The reaction between Ni- and C-containing particles was discussed, and the influences of bilayer periods on the structure and morphology, accompanied with the frictional behaviors at different loading forces (2 and 5 N), as well as the field emission properties were investigated. The results showed that Ni grew in the (111) plane, and there was no Ni–C bond or graphene formed in the film because of the relatively lower energy during deposition. Moreover, the content of sp2C in the film, the hardness, and the field emission performance exhibited an initial increase followed by a subsequent decrease with increasing bilayer periods. However, the frictional coefficient decreased owing to more graphitization with an increase of the applied load. Particularly noteworthy was that the film possessed a bilayer period of 710 nm, displayed a compact structure with a smaller grain size, and showed reduced sp2C content in the role of Ni. This resulted in sustained lower surface roughness, heightened hardness, decreased coefficient of friction, and a smaller opening electric field.