Arturo Mandujano-Nava
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arturo Mandujano-Nava has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Mauro Paz-Cabrera
Universidad Politécnica de Guanajuato
4 shared publications - Jesús Chihuaque-Alcantar
Universidad Politécnica de Guanajuato
3 shared publications - Tomás Serrano-Ramírez
Universidad Politécnica de Guanajuato
3 shared publications - Yosafat Jetsemaní Sámano-Flores
Universidad Politécnica de Guanajuato
3 shared publications - José De La Cruz Mendoza Derramadero
Tecnológico Nacional de México
2 shared publications - Pedro López Rodríguez
Universidad Politécnica de Guanajuato
2 shared publications
Latest Publications
- Open Access
- 30 December 2025
- Published by ECORFAN in Journal of Quantitative and Statistical Analysis
Statistical assessment of vehicle emissions according to traction type in Celaya, México
Transportation represents a major environmental challenge due to its CO₂ emissions. In Mexico, the continuous growth of the vehicle fleet increases the consumption of fossil fuels and the release of greenhouse gases [GHG]. This study statistically evaluates vehicular emissions in Celaya, Guanajuato, comparing different drivetrain types: front-wheel drive [FWD], rear-wheel drive [RWD], and all-wheel drive [AWD]. The analysis incorporates data from the Public Vehicle Registry [REPUVE], the Portal of Energy Efficiency Indicators and Vehicle Emissions [EcoVehicles, 2022], and local fuel-consumption surveys. Results show that FWD vehicles record lower average emissions [≈198 gCO₂/km] compared with RWD and AWD vehicles [≈290 gCO₂/km]. Sedans, which are mostly FWD, present the lowest values, while sport utility vehicles [SUVs] and pickup trucks exhibit the highest. The drivetrain configuration plays a significant role in energy efficiency and environmental impact. While FWD contributes to reducing emissions, the increasing presence of SUVs and pickups in the fleet may lead to higher overall CO₂ levels.
- 30 December 2025
- Published by ECORFAN in Journal of Quantitative and Statistical Analysis
Open AccessStatistical assessment of vehicle emissions according to traction type in Celaya, México
Transportation represents a major environmental challenge due to its CO₂ emissions. In Mexico, the continuous growth of the vehicle fleet increases the consumption of fossil fuels and the release of greenhouse gases [GHG]. This study statistically evaluates vehicular emissions in Celaya, Guanajuato, comparing different drivetrain types: front-wheel drive [FWD], rear-wheel drive [RWD], and all-wheel drive [AWD]. The analysis incorporates data from the Public Vehicle Registry [REPUVE], the Portal of Energy Efficiency Indicators and Vehicle Emissions [EcoVehicles, 2022], and local fuel-consumption surveys. Results show that FWD vehicles record lower average emissions [≈198 gCO₂/km] compared with RWD and AWD vehicles [≈290 gCO₂/km]. Sedans, which are mostly FWD, present the lowest values, while sport utility vehicles [SUVs] and pickup trucks exhibit the highest. The drivetrain configuration plays a significant role in energy efficiency and environmental impact. While FWD contributes to reducing emissions, the increasing presence of SUVs and pickups in the fleet may lead to higher overall CO₂ levels.
- Open Access
- 30 December 2025
- Published by ECORFAN in Revista del Diseño Innovativo
Battery pack design with MATLAB battery builder tools and CAD software for compact electric vehicle
Currently, electric and hybrid vehicles have enjoyed greater consumer acceptance, as reflected in global sales figures from the International Energy Agency [IEA]. Therefore, this work proposes the conceptual design of a prototype of a battery pack with BYD Blade prismatic cells and A123ANR26650 cylindrical battery pack through Battery Builder MATLAB tools and CAD software for a BYD Dolphin 2024 EV vehicle. Applying these tools, virtual prototypes of a prismatic battery pack and a cylindrical battery pack were modeled, which achieve the energy storage requirements indicated in the vehicle's technical data sheet. A comparison is also made between the two packs based on the number of cells required, weight, and dimensions of the battery tray.
- 30 December 2025
- Published by ECORFAN in Revista del Diseño Innovativo
Open AccessBattery pack design with MATLAB battery builder tools and CAD software for compact electric vehicle
Currently, electric and hybrid vehicles have enjoyed greater consumer acceptance, as reflected in global sales figures from the International Energy Agency [IEA]. Therefore, this work proposes the conceptual design of a prototype of a battery pack with BYD Blade prismatic cells and A123ANR26650 cylindrical battery pack through Battery Builder MATLAB tools and CAD software for a BYD Dolphin 2024 EV vehicle. Applying these tools, virtual prototypes of a prismatic battery pack and a cylindrical battery pack were modeled, which achieve the energy storage requirements indicated in the vehicle's technical data sheet. A comparison is also made between the two packs based on the number of cells required, weight, and dimensions of the battery tray.
- Open Access
- 31 December 2024
- Published by ECORFAN in Revista de Energías Renovables
Design of a High Performance Hybrid Tricycle (THAR) to assist people with motor disabilities
In Mexico, there is a delay in the mobility process of people with motor disabilities. At the same time, in our country there are nearly 3 million people with motor disabilities according to what INEGI reports in its 2020 census. Therefore, a virtual prototype is being proposed as a result of the first stage of its own methodology for the design of a hybrid tricycle to transport people with motor disabilities, which offers versatility in terms of transport configurations in the facilities of the Polytechnic University of Guanajuato (UPG). In a second stage, it is proposed to build a scale prototype using additive manufacturing to identify areas of opportunity before building the final prototype and carrying out its real physical tests in order to obtain sufficient data to implement a commercial model that can be reproduced. reliable way.
- 31 December 2024
- Published by ECORFAN in Revista de Energías Renovables
Open AccessDesign of a High Performance Hybrid Tricycle (THAR) to assist people with motor disabilities
In Mexico, there is a delay in the mobility process of people with motor disabilities. At the same time, in our country there are nearly 3 million people with motor disabilities according to what INEGI reports in its 2020 census. Therefore, a virtual prototype is being proposed as a result of the first stage of its own methodology for the design of a hybrid tricycle to transport people with motor disabilities, which offers versatility in terms of transport configurations in the facilities of the Polytechnic University of Guanajuato (UPG). In a second stage, it is proposed to build a scale prototype using additive manufacturing to identify areas of opportunity before building the final prototype and carrying out its real physical tests in order to obtain sufficient data to implement a commercial model that can be reproduced. reliable way.
- 31 December 2023
- Published by ECORFAN in ECORFAN Journal Taiwan
- p. 15-23
Processing and recognition of EMG signals through CNN networks for the control of electric vehicles
The increase in autonomous driving technologies, as well as biometrics using biosignals from vehicle drivers, provide information that can be used for the development of personalized biosecurity and driving systems for each user. Currently, studies are being carried out on the extraction and classification of driver characteristics with great precision, to generate intelligent systems that are auxiliary and that help to safeguard the integrity of people while driving vehicles. This work presents the recognition of 5 hand gestures to control the driving actions of an electric vehicle using the EMG signals from the MYOTM bracelet, these signals have also been used to detect users and thus allow the use only of the people registered in the application. To perform gesture recognition, a convolutional neural network was trained and implemented for the classification of actions. Finally, a cross-validation was carried out to validate the reliability of the proposed system, obtaining 99.2% accuracy during the classification.
- 31 December 2023
- Published by ECORFAN in ECORFAN Journal Taiwan
- p. 15-23
Processing and recognition of EMG signals through CNN networks for the control of electric vehicles
The increase in autonomous driving technologies, as well as biometrics using biosignals from vehicle drivers, provide information that can be used for the development of personalized biosecurity and driving systems for each user. Currently, studies are being carried out on the extraction and classification of driver characteristics with great precision, to generate intelligent systems that are auxiliary and that help to safeguard the integrity of people while driving vehicles. This work presents the recognition of 5 hand gestures to control the driving actions of an electric vehicle using the EMG signals from the MYOTM bracelet, these signals have also been used to detect users and thus allow the use only of the people registered in the application. To perform gesture recognition, a convolutional neural network was trained and implemented for the classification of actions. Finally, a cross-validation was carried out to validate the reliability of the proposed system, obtaining 99.2% accuracy during the classification.
- Open Access
- 30 June 2022
- Published by ECORFAN in Revista de Tecnologías en procesos Industriales
- p. 15-21
Didactic prototype of a robotic manufacturing cell to program welding trajectories in a frame
This project shows the integration of a didactic prototype of a robotic manufacturing cell for the programming of welding trajectories in a chassis. The purpose of this project is to integrate the robotic cell through the interaction of the controller of an industrial robot, a programmable logic controller (PLC) and a power transmission system for the positioning of a chassis for didactic purposes for students studying engineering in the area of Industrial Automation. To carry out the project, a scale chassis for a tractor and its support base was first manufactured, then the control of a stepper motor was carried out through a SIMATIC S7-1200 CPU 1214C PLC and a microstep driver module. The programming software COSIMIR from FESTO was also used to program the welding trajectories in a Mitsubishi RV-2AJ robot with 5 degrees of freedom that interacts with the PLC through input and output digital modules. Finally, it was possible to obtain a functional prototype of a robotic manufacturing cell that can be used for teaching robot trajectory programming and that is closely related to industrial machines.
- 30 June 2022
- Published by ECORFAN in Revista de Tecnologías en procesos Industriales
- p. 15-21
Open AccessDidactic prototype of a robotic manufacturing cell to program welding trajectories in a frame
This project shows the integration of a didactic prototype of a robotic manufacturing cell for the programming of welding trajectories in a chassis. The purpose of this project is to integrate the robotic cell through the interaction of the controller of an industrial robot, a programmable logic controller (PLC) and a power transmission system for the positioning of a chassis for didactic purposes for students studying engineering in the area of Industrial Automation. To carry out the project, a scale chassis for a tractor and its support base was first manufactured, then the control of a stepper motor was carried out through a SIMATIC S7-1200 CPU 1214C PLC and a microstep driver module. The programming software COSIMIR from FESTO was also used to program the welding trajectories in a Mitsubishi RV-2AJ robot with 5 degrees of freedom that interacts with the PLC through input and output digital modules. Finally, it was possible to obtain a functional prototype of a robotic manufacturing cell that can be used for teaching robot trajectory programming and that is closely related to industrial machines.
- Open Access
- 30 June 2021
- Published by ECORFAN in Revista Tecnologías de la Información y Comunicaciones
- p. 20-25
Artificial vision system for object classification in real time using Raspberry Pi and a Web camera
Computer vision systems are an essential part in industrial automation tasks such as: identification, selection, measurement, defect detection and quality control in parts and components. There are smart cameras used to perform tasks, however, their high acquisition and maintenance cost is restrictive. In this work, a novel low-cost artificial vision system is proposed for classifying objects in real time, using the Raspberry Pi 3B + embedded system, a Web camera and the Open CV artificial vision library. The suggested technique comprises the training of a supervised classification system of the Haar Cascade type, with image banks of the object to be recognized, subsequently generating a predictive model which is put to the test with real-time detection, as well as the calculation for the prediction error. This seeks to build a powerful vision system, affordable and also developed using free software.
- 30 June 2021
- Published by ECORFAN in Revista Tecnologías de la Información y Comunicaciones
- p. 20-25
Open AccessArtificial vision system for object classification in real time using Raspberry Pi and a Web camera
Computer vision systems are an essential part in industrial automation tasks such as: identification, selection, measurement, defect detection and quality control in parts and components. There are smart cameras used to perform tasks, however, their high acquisition and maintenance cost is restrictive. In this work, a novel low-cost artificial vision system is proposed for classifying objects in real time, using the Raspberry Pi 3B + embedded system, a Web camera and the Open CV artificial vision library. The suggested technique comprises the training of a supervised classification system of the Haar Cascade type, with image banks of the object to be recognized, subsequently generating a predictive model which is put to the test with real-time detection, as well as the calculation for the prediction error. This seeks to build a powerful vision system, affordable and also developed using free software.
- Open Access
- 31 December 2020
- Published by ECORFAN in Journal of Technology and Innovation
- p. 19-25
Prototype of natural user interface applied to a robotic arm for medical attention preventing nosocomial infections in healthcare personnel
In this work, an experimental prototype of natural user interface based on Kinect for the tele-operation of a robotic arm, was developed as a technological support to contribute in facing the global crisis of health generated by COVID-19, a dangerous and highly transmissible virus. Until now, it is causing thousands of deaths and growing of contagion rates around the world, involving a serious situation for healthcare personnel that works in hospitals attending infected population. This system was proposed with the aim to control a robotic arm for medical purposes to achieve a quality medical care to COVID-19 patients without risk implications for healthcare workers associated to nosocomial infections due to direct contact with infected patients, contaminated medical equipment, surgical objects and surfaces. The developed prototype is able of being manipulated in real time requiring neither physical controller nor any contact device to carry out its functions, but simply motion or gesture from the user’s arm. It can be applied in areas such as teleoperation, tele-rehabilitation, telehealth nursing, assistive and therapeutic robotic devices, elderly care which are the last tendency in medicine at this time. Kinect V2, the Software Development kit SDK 2.0, Microsoft visual C# and Arduino were used for this purpose.
- 31 December 2020
- Published by ECORFAN in Journal of Technology and Innovation
- p. 19-25
Open AccessPrototype of natural user interface applied to a robotic arm for medical attention preventing nosocomial infections in healthcare personnel
In this work, an experimental prototype of natural user interface based on Kinect for the tele-operation of a robotic arm, was developed as a technological support to contribute in facing the global crisis of health generated by COVID-19, a dangerous and highly transmissible virus. Until now, it is causing thousands of deaths and growing of contagion rates around the world, involving a serious situation for healthcare personnel that works in hospitals attending infected population. This system was proposed with the aim to control a robotic arm for medical purposes to achieve a quality medical care to COVID-19 patients without risk implications for healthcare workers associated to nosocomial infections due to direct contact with infected patients, contaminated medical equipment, surgical objects and surfaces. The developed prototype is able of being manipulated in real time requiring neither physical controller nor any contact device to carry out its functions, but simply motion or gesture from the user’s arm. It can be applied in areas such as teleoperation, tele-rehabilitation, telehealth nursing, assistive and therapeutic robotic devices, elderly care which are the last tendency in medicine at this time. Kinect V2, the Software Development kit SDK 2.0, Microsoft visual C# and Arduino were used for this purpose.
- Open Access
- 31 December 2019
- Published by ECORFAN in Revista del Desarrollo Tecnologico
- p. 1-6
Diseño y desarrollo de un prototipo Checking – Fixture para componentes de la industria automotriz con un enfoque hacia la industria 4.0
The present work shows the design and the integration of several complements in a device at prototype level that carries out the tracking of the physical and dimensional characteristics for components of the automotive industry based on the new technological trends, as it is the industry 4.0. For this purpose, CAD design software such as Solidworks 2017 is used, the use of CAM systems with EdgeCam 2019 software as a manufacturing element, the vision system is used using the Matlab software and the Minitab 2017 statistical tool as an interface a device that helps to know the behavior of the parameters that are defined as critical in the production of automotive components and be able to carry out the necessary adjustments in the production parameters to reduce the variability in the process. Looking to have information in real time and make timely decisions. Generating the corresponding statistical control charts, with the aim of avoiding possible reworking or in the case of scrap generation.
- 31 December 2019
- Published by ECORFAN in Revista del Desarrollo Tecnologico
- p. 1-6
Open AccessDiseño y desarrollo de un prototipo Checking – Fixture para componentes de la industria automotriz con un enfoque hacia la industria 4.0
The present work shows the design and the integration of several complements in a device at prototype level that carries out the tracking of the physical and dimensional characteristics for components of the automotive industry based on the new technological trends, as it is the industry 4.0. For this purpose, CAD design software such as Solidworks 2017 is used, the use of CAM systems with EdgeCam 2019 software as a manufacturing element, the vision system is used using the Matlab software and the Minitab 2017 statistical tool as an interface a device that helps to know the behavior of the parameters that are defined as critical in the production of automotive components and be able to carry out the necessary adjustments in the production parameters to reduce the variability in the process. Looking to have information in real time and make timely decisions. Generating the corresponding statistical control charts, with the aim of avoiding possible reworking or in the case of scrap generation.
- Open Access
- 31 December 2019
- Published by ECORFAN in Journal Public Economy
- p. 1-13
Sustainability in higher education schools in México
The increase of gases in the ozone layer is an important issue nowadays in the Universities of Higher Education in Mexico; there is a great interest in contributing to the reduction of the carbon footprint, therefore, a study was carried out to calculate the footprint generated by the students of the Polytechnic University of Guanajuato through the use of software. The participants were 27 students of the Automotive Engineering degree of the sixth semester, which during this period kept a record of the consumption of PET bottles in their various presentations. The main findings were that the total CO2 they produce is 131.7 Kg, which would be equivalent to 0.176 barrels of oil and 1.19 m3 of space saved in landfills. Now, taking into consideration the entire student population (3,899), the calculation was projected annually and estimating the same consumption patterns, would save 76.3 barrels of oil against 515.55 m3 of space in sanitary landfills.
- 31 December 2019
- Published by ECORFAN in Journal Public Economy
- p. 1-13
Open AccessSustainability in higher education schools in México
The increase of gases in the ozone layer is an important issue nowadays in the Universities of Higher Education in Mexico; there is a great interest in contributing to the reduction of the carbon footprint, therefore, a study was carried out to calculate the footprint generated by the students of the Polytechnic University of Guanajuato through the use of software. The participants were 27 students of the Automotive Engineering degree of the sixth semester, which during this period kept a record of the consumption of PET bottles in their various presentations. The main findings were that the total CO2 they produce is 131.7 Kg, which would be equivalent to 0.176 barrels of oil and 1.19 m3 of space saved in landfills. Now, taking into consideration the entire student population (3,899), the calculation was projected annually and estimating the same consumption patterns, would save 76.3 barrels of oil against 515.55 m3 of space in sanitary landfills.