Tomás Serrano-Ramírez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tomás Serrano-Ramírez has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Arturo Mandujano-Nava
Tecnológico Nacional de México
3 shared publications - Diana Guadalupe Gutiérrez-León
Department of Robotics, Mechatronics, and Data Engineering, Polytechnic University of Guanajuato, Guanajuato, Mexico
2 shared publications - Julio C. Peña-Aguirre
Ingeniera automotriz, Universidad Politcnica de Guanajuato, Cortazar, Mexico
2 shared publications - Yosafat Jetsemaní Sámano-Flores
Universidad Politécnica de Guanajuato
2 shared publications - Alberto Lozano-Díaz
Universidad Politécnica de Guanajuato
1 shared publication - Alejandro Israel Barranco-Gutiérrez
Departamento de Ingeniería Electrónica, Tecnológico Nacional de México (TecNM), Instituto Tecnológico de Celaya (ITC), Celaya 38010, Guanajuato, Mexico
1 shared publication
Latest Publications
- Open Access
- 7 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 129040-129055
Energy Management System Comparison Among Fuzzy Strategies
This study evaluates and compares energy management systems (EMS) for hybrid vehicles using fuzzy logic strategies to optimize energy distribution between fuel cells (FC) and batteries. Key components, including the Proton Exchange Membrane Fuel Cell (PEMFC) and the Permanent Magnet Synchronous Motor (PMSM), were modeled and validated using MATLAB-Simulink, LabVIEW, and Hardware-in-the-Loop (HIL) testing. Peña’s EMS demonstrated the highest efficiency, achieving a fuel cell average power output of 8.5 kW, an efficiency of 74.35%, and a state of charge (SOC) improvement of 34.25%. Other strategies, including those of Esoufi, Hemi, and Zhao, exhibited average power outputs ranging from 7.28 to 7.79 kW and SOC improvements of 22.96% to 28.35%. These results emphasize the advantages of Peña’s fuzzy logic-based EMS in balancing energy demands, reducing battery stress, and extending battery life under urban driving conditions. The findings highlight fuzzy logic as a superior approach to traditional methods for managing hybrid vehicle powertrains, particularly in scenarios with frequent acceleration and deceleration.
- 7 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 129040-129055
Open AccessEnergy Management System Comparison Among Fuzzy Strategies
This study evaluates and compares energy management systems (EMS) for hybrid vehicles using fuzzy logic strategies to optimize energy distribution between fuel cells (FC) and batteries. Key components, including the Proton Exchange Membrane Fuel Cell (PEMFC) and the Permanent Magnet Synchronous Motor (PMSM), were modeled and validated using MATLAB-Simulink, LabVIEW, and Hardware-in-the-Loop (HIL) testing. Peña’s EMS demonstrated the highest efficiency, achieving a fuel cell average power output of 8.5 kW, an efficiency of 74.35%, and a state of charge (SOC) improvement of 34.25%. Other strategies, including those of Esoufi, Hemi, and Zhao, exhibited average power outputs ranging from 7.28 to 7.79 kW and SOC improvements of 22.96% to 28.35%. These results emphasize the advantages of Peña’s fuzzy logic-based EMS in balancing energy demands, reducing battery stress, and extending battery life under urban driving conditions. The findings highlight fuzzy logic as a superior approach to traditional methods for managing hybrid vehicle powertrains, particularly in scenarios with frequent acceleration and deceleration.
- Open Access
- 31 December 2024
- Published by ECORFAN in Journal of Technological Prototypes
Design of a single-seater chassis for a BAJA SAE vehicle
This work presents the conceptual design of a single-seater chassis for a BAJA SAE off-road vehicle, using the Pahl and Beitz design methodology, with the objective of developing an efficient, safe prototype capable of withstanding the demands of off-road competitions. The weighted index method was applied to evaluate and select the components that best meet the requirements established in the official BAJA SAE regulations, ensuring an optimal balance between weight, strength, and cost. To ensure the structural integrity of the chassis, frontal and lateral impact analyses were conducted using finite element simulation, where the chassis's ability to withstand 4G loads at different critical points of the structure was evaluated. The results revealed that the stresses generated in the frontal impact are significantly higher compared to other analyses, suggesting the need to reinforce this part of the chassis in future development stages
- 31 December 2024
- Published by ECORFAN in Journal of Technological Prototypes
Open AccessDesign of a single-seater chassis for a BAJA SAE vehicle
This work presents the conceptual design of a single-seater chassis for a BAJA SAE off-road vehicle, using the Pahl and Beitz design methodology, with the objective of developing an efficient, safe prototype capable of withstanding the demands of off-road competitions. The weighted index method was applied to evaluate and select the components that best meet the requirements established in the official BAJA SAE regulations, ensuring an optimal balance between weight, strength, and cost. To ensure the structural integrity of the chassis, frontal and lateral impact analyses were conducted using finite element simulation, where the chassis's ability to withstand 4G loads at different critical points of the structure was evaluated. The results revealed that the stresses generated in the frontal impact are significantly higher compared to other analyses, suggesting the need to reinforce this part of the chassis in future development stages
- Open Access
- 30 June 2022
- Published by ECORFAN in Revista de Tecnologías en procesos Industriales
- p. 15-21
Didactic prototype of a robotic manufacturing cell to program welding trajectories in a frame
This project shows the integration of a didactic prototype of a robotic manufacturing cell for the programming of welding trajectories in a chassis. The purpose of this project is to integrate the robotic cell through the interaction of the controller of an industrial robot, a programmable logic controller (PLC) and a power transmission system for the positioning of a chassis for didactic purposes for students studying engineering in the area of Industrial Automation. To carry out the project, a scale chassis for a tractor and its support base was first manufactured, then the control of a stepper motor was carried out through a SIMATIC S7-1200 CPU 1214C PLC and a microstep driver module. The programming software COSIMIR from FESTO was also used to program the welding trajectories in a Mitsubishi RV-2AJ robot with 5 degrees of freedom that interacts with the PLC through input and output digital modules. Finally, it was possible to obtain a functional prototype of a robotic manufacturing cell that can be used for teaching robot trajectory programming and that is closely related to industrial machines.
- 30 June 2022
- Published by ECORFAN in Revista de Tecnologías en procesos Industriales
- p. 15-21
Open AccessDidactic prototype of a robotic manufacturing cell to program welding trajectories in a frame
This project shows the integration of a didactic prototype of a robotic manufacturing cell for the programming of welding trajectories in a chassis. The purpose of this project is to integrate the robotic cell through the interaction of the controller of an industrial robot, a programmable logic controller (PLC) and a power transmission system for the positioning of a chassis for didactic purposes for students studying engineering in the area of Industrial Automation. To carry out the project, a scale chassis for a tractor and its support base was first manufactured, then the control of a stepper motor was carried out through a SIMATIC S7-1200 CPU 1214C PLC and a microstep driver module. The programming software COSIMIR from FESTO was also used to program the welding trajectories in a Mitsubishi RV-2AJ robot with 5 degrees of freedom that interacts with the PLC through input and output digital modules. Finally, it was possible to obtain a functional prototype of a robotic manufacturing cell that can be used for teaching robot trajectory programming and that is closely related to industrial machines.
- Open Access
- 30 June 2021
- Published by ECORFAN in Revista Tecnologías de la Información y Comunicaciones
- p. 20-25
Artificial vision system for object classification in real time using Raspberry Pi and a Web camera
Computer vision systems are an essential part in industrial automation tasks such as: identification, selection, measurement, defect detection and quality control in parts and components. There are smart cameras used to perform tasks, however, their high acquisition and maintenance cost is restrictive. In this work, a novel low-cost artificial vision system is proposed for classifying objects in real time, using the Raspberry Pi 3B + embedded system, a Web camera and the Open CV artificial vision library. The suggested technique comprises the training of a supervised classification system of the Haar Cascade type, with image banks of the object to be recognized, subsequently generating a predictive model which is put to the test with real-time detection, as well as the calculation for the prediction error. This seeks to build a powerful vision system, affordable and also developed using free software.
- 30 June 2021
- Published by ECORFAN in Revista Tecnologías de la Información y Comunicaciones
- p. 20-25
Open AccessArtificial vision system for object classification in real time using Raspberry Pi and a Web camera
Computer vision systems are an essential part in industrial automation tasks such as: identification, selection, measurement, defect detection and quality control in parts and components. There are smart cameras used to perform tasks, however, their high acquisition and maintenance cost is restrictive. In this work, a novel low-cost artificial vision system is proposed for classifying objects in real time, using the Raspberry Pi 3B + embedded system, a Web camera and the Open CV artificial vision library. The suggested technique comprises the training of a supervised classification system of the Haar Cascade type, with image banks of the object to be recognized, subsequently generating a predictive model which is put to the test with real-time detection, as well as the calculation for the prediction error. This seeks to build a powerful vision system, affordable and also developed using free software.
- Open Access
- 31 December 2020
- Published by ECORFAN in Journal of Technology and Innovation
- p. 19-25
Prototype of natural user interface applied to a robotic arm for medical attention preventing nosocomial infections in healthcare personnel
In this work, an experimental prototype of natural user interface based on Kinect for the tele-operation of a robotic arm, was developed as a technological support to contribute in facing the global crisis of health generated by COVID-19, a dangerous and highly transmissible virus. Until now, it is causing thousands of deaths and growing of contagion rates around the world, involving a serious situation for healthcare personnel that works in hospitals attending infected population. This system was proposed with the aim to control a robotic arm for medical purposes to achieve a quality medical care to COVID-19 patients without risk implications for healthcare workers associated to nosocomial infections due to direct contact with infected patients, contaminated medical equipment, surgical objects and surfaces. The developed prototype is able of being manipulated in real time requiring neither physical controller nor any contact device to carry out its functions, but simply motion or gesture from the user’s arm. It can be applied in areas such as teleoperation, tele-rehabilitation, telehealth nursing, assistive and therapeutic robotic devices, elderly care which are the last tendency in medicine at this time. Kinect V2, the Software Development kit SDK 2.0, Microsoft visual C# and Arduino were used for this purpose.
- 31 December 2020
- Published by ECORFAN in Journal of Technology and Innovation
- p. 19-25
Open AccessPrototype of natural user interface applied to a robotic arm for medical attention preventing nosocomial infections in healthcare personnel
In this work, an experimental prototype of natural user interface based on Kinect for the tele-operation of a robotic arm, was developed as a technological support to contribute in facing the global crisis of health generated by COVID-19, a dangerous and highly transmissible virus. Until now, it is causing thousands of deaths and growing of contagion rates around the world, involving a serious situation for healthcare personnel that works in hospitals attending infected population. This system was proposed with the aim to control a robotic arm for medical purposes to achieve a quality medical care to COVID-19 patients without risk implications for healthcare workers associated to nosocomial infections due to direct contact with infected patients, contaminated medical equipment, surgical objects and surfaces. The developed prototype is able of being manipulated in real time requiring neither physical controller nor any contact device to carry out its functions, but simply motion or gesture from the user’s arm. It can be applied in areas such as teleoperation, tele-rehabilitation, telehealth nursing, assistive and therapeutic robotic devices, elderly care which are the last tendency in medicine at this time. Kinect V2, the Software Development kit SDK 2.0, Microsoft visual C# and Arduino were used for this purpose.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Low Temperature Plasma by Corona discharge in water: lethal effect on Escherichia coli and Salmonella enterica serotype Typhimurium
In this research work, inactivation of two significant global contributors to microbiological problems in water was carried out: Escherichia coli and Salmonella enterica serotype Typhimurium. Both are representative of fecal pollution and their presence could compromise water quality and food safety generating serious effects on human health.Simultaneous inactivation process of Escherichia coli and Salmonella enterica serotype Typhimurium involved the production of Low Temperature Plasma from Positive Corona discharge (20 kV, 0.45 mA) at atmospheric conditions. Initial bacteria concentrations in water were respectively, 3.4 log CFU/ml and 3.6 log CFU/ml, which are typical from poultry activities.High effectiveness (> 99%) in the process was obtained at the end of 180 s and, total inactivation of Escherichia coli and Salmonella enterica serotype Typhimurium was achieved at 360 s. During treatment, Escherichia coli bacteria showed major resistance to be reduced; nevertheless, synergistic lethal effects generated in water during the production of plasma: reactive chemical species, shock waves and UV radiation, allowed to get null bacteria survival.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Low Temperature Plasma by Corona discharge in water: lethal effect on Escherichia coli and Salmonella enterica serotype Typhimurium
In this research work, inactivation of two significant global contributors to microbiological problems in water was carried out: Escherichia coli and Salmonella enterica serotype Typhimurium. Both are representative of fecal pollution and their presence could compromise water quality and food safety generating serious effects on human health.Simultaneous inactivation process of Escherichia coli and Salmonella enterica serotype Typhimurium involved the production of Low Temperature Plasma from Positive Corona discharge (20 kV, 0.45 mA) at atmospheric conditions. Initial bacteria concentrations in water were respectively, 3.4 log CFU/ml and 3.6 log CFU/ml, which are typical from poultry activities.High effectiveness (> 99%) in the process was obtained at the end of 180 s and, total inactivation of Escherichia coli and Salmonella enterica serotype Typhimurium was achieved at 360 s. During treatment, Escherichia coli bacteria showed major resistance to be reduced; nevertheless, synergistic lethal effects generated in water during the production of plasma: reactive chemical species, shock waves and UV radiation, allowed to get null bacteria survival.