Alena Gennadievna Upolovnikova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Alena Gennadievna Upolovnikova has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- A. N. Smetannikov
Vatolin Institute of Metallurgy, Ural Branch of the Russian Academy of Sciences, Ekaterinburg, Russian Federation
16 shared publications - Anatoly Babenko
Institute of Metallurgy, Ural Branch, Russian Academy of Sciences, Yekaterinburg, Russia
13 shared publications - Ruslan Shartdinov
Vatolin Institute of Metallurgy, Ural Branch of the Russian Academy of Sciences, Ekaterinburg, Russian Federation
11 shared publications - A. A. Babenko
Institute of Metallurgy, UB RAS
8 shared publications V. I. Zhuchkov
Institute of Metallurgy of the Ural Branch of the Russian Academy of Sciences
5 shared publicationsA. A. Babenko
Institute of Metallurgy, Ural Branch, Russian Academy of Sciences, Yekaterinburg, Russia
4 shared publications
Latest Publications
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1947-1954
Construction of viscosity diagrams for blast-furnace slag of the CaO-SiO2-Al2O3-10%MgO-2%TiO2-0.5%MnO system by the method of simplex lattices
- 1 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (12) , 1947-1954
Construction of viscosity diagrams for blast-furnace slag of the CaO-SiO2-Al2O3-10%MgO-2%TiO2-0.5%MnO system by the method of simplex lattices
- 7 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (10) , 14694-14705
Effect of B2O3 on the structure and melt viscosity of CaO–8wt.%MgO–15 wt%Al2O3–SiO2–B2O3 refining slag at CaO/SiO2 mass ratio of 2 to 5
- 7 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (10) , 14694-14705
Effect of B2O3 on the structure and melt viscosity of CaO–8wt.%MgO–15 wt%Al2O3–SiO2–B2O3 refining slag at CaO/SiO2 mass ratio of 2 to 5
- Open Access
- 8 November 2025
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 68 (5) , 488-494
Features of application of boron-containing slags in stainless steel smelting
Traditionally, for stainless steel smelting in the process of argon-oxygen decarburization, fluorspar is used to liquefy the slag and ensure the normal course of the refining and reduction of chromium oxide. Fluospar is characterized by high volatility at high temperatures of the steelmaking process, while the resulting compounds are toxic and hazardous to the environment. For this reason, the paper considers the replacement of fluorspar with boron oxide, which is also capable of forming low-melting eutectics with the main components of slag, at the final stage of steel processing during the argon-oxygen decarburization process – during the desulfurization period. It was found that, despite an increase in the degree of slag polymerization as a result of the introduction of boron oxide to 6 %, due to its ability to form low-melting compounds, an increase in its content has a beneficial effect on the fluidity of slags of the studied СаО – SiO 2 – В 2 O 3 – 2 % Cr 2 O 3 – 3 % Аl 2 O 3 – 8 % МgO system at a basicity of CaO/SiO 2 of 1.0 and 2.5. The content of 6 % B 2 O 3 in slag with a high basicity of 2.5 makes it possible to achieve viscosity values of 0.3 Pa·s, which are favorable for sulfur removal. In this case, the equilibrium sulfur content in the metal can reach 0.003 % according to the thermodynamic modeling. As a result of the experimental studies, the minimum sulfur content was 0.006 %, which is close to the equilibrium concentration. During the treatment of steel samples with slags, direct steel microalloying with boron in the amount of 0.002 – 0.003 % occurred. A small amount of boron transferred to steel during direct microalloying, according to literary data, has a beneficial effect on the ductility and corrosion resistance of the metal product.
- 8 November 2025
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 68 (5) , 488-494
Open AccessFeatures of application of boron-containing slags in stainless steel smelting
Traditionally, for stainless steel smelting in the process of argon-oxygen decarburization, fluorspar is used to liquefy the slag and ensure the normal course of the refining and reduction of chromium oxide. Fluospar is characterized by high volatility at high temperatures of the steelmaking process, while the resulting compounds are toxic and hazardous to the environment. For this reason, the paper considers the replacement of fluorspar with boron oxide, which is also capable of forming low-melting eutectics with the main components of slag, at the final stage of steel processing during the argon-oxygen decarburization process – during the desulfurization period. It was found that, despite an increase in the degree of slag polymerization as a result of the introduction of boron oxide to 6 %, due to its ability to form low-melting compounds, an increase in its content has a beneficial effect on the fluidity of slags of the studied СаО – SiO 2 – В 2 O 3 – 2 % Cr 2 O 3 – 3 % Аl 2 O 3 – 8 % МgO system at a basicity of CaO/SiO 2 of 1.0 and 2.5. The content of 6 % B 2 O 3 in slag with a high basicity of 2.5 makes it possible to achieve viscosity values of 0.3 Pa·s, which are favorable for sulfur removal. In this case, the equilibrium sulfur content in the metal can reach 0.003 % according to the thermodynamic modeling. As a result of the experimental studies, the minimum sulfur content was 0.006 %, which is close to the equilibrium concentration. During the treatment of steel samples with slags, direct steel microalloying with boron in the amount of 0.002 – 0.003 % occurred. A small amount of boron transferred to steel during direct microalloying, according to literary data, has a beneficial effect on the ductility and corrosion resistance of the metal product.
- 1 October 2025
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2025 (10) , 1830-1833
Analysis of Nonmetallic Inclusions in Steel When Cerium Oxide Is Used in Ladle Metallurgy Slags
The development of effective technological methods for controlling the formation of nonmetallic inclusions (NMIs) is a promising direction for improving the properties and quality characteristics of steels. The sulfur content is one of the factors controlling the quantity, morphology, and distribution (over the metal volume) of sulfide inclusions is. To organize the production of steel with a low (down to 0.003%) sulfur content, desulfurization is carried out at ladle furnace units with the formation of basic Ca–SiO2–Al2O3 slags and deep aluminum deoxidation of steel. Here, one of the main oxide inclusions in aluminum-killed steel is corundum (Al2O3), which impairs the properties of steel and leads to “clogging” of the inner surface of a submerged entry nozzle during continuous casting. The negative effect of corundum in steel can be neutralized by its removal into the basic fluid slag formed in a ladle furnace unit by decreasing the activity of Al2O3. However, in practice, an excessive increase in the basicity of a refining slag to decrease the activity of Al2O3 is usually accompanied by slag heterogenization, an increase in the melting temperature of slag, and a decrease in its refining properties. The use of rare earth metal (REM) oxide additives can be a promising direction for decreasing the activity coefficient of Al2O3 in basic refining slags. The application of REM oxides ensures a decrease in their melting temperature, an increase in the fluidity, an increase in the sulfur distribution ratio, and a decrease in the REM distribution ratio. In this wok, we study the influence of cerium oxide in Ca–SiO2–Al2O3–MgO–Ce2O3 slags on NMIs. Experimental samples of clean steel held under a slag containing 15.0% cerium oxide exhibit the presence of up to 10 ppm cerium in the metal, a decrease in the total oxygen concentration to 13 ppm, a decrease in sulfur in the metal from 20 to 5 ppm, and the absence of manganese sulfide and corundum (Al2O3) NMIs. The Ce2O2S oxysulfide phase, magnesium and cerium oxide inclusions, and the MgO–Al2O3 oxide phase are also detected.
- 1 October 2025
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2025 (10) , 1830-1833
Analysis of Nonmetallic Inclusions in Steel When Cerium Oxide Is Used in Ladle Metallurgy Slags
The development of effective technological methods for controlling the formation of nonmetallic inclusions (NMIs) is a promising direction for improving the properties and quality characteristics of steels. The sulfur content is one of the factors controlling the quantity, morphology, and distribution (over the metal volume) of sulfide inclusions is. To organize the production of steel with a low (down to 0.003%) sulfur content, desulfurization is carried out at ladle furnace units with the formation of basic Ca–SiO2–Al2O3 slags and deep aluminum deoxidation of steel. Here, one of the main oxide inclusions in aluminum-killed steel is corundum (Al2O3), which impairs the properties of steel and leads to “clogging” of the inner surface of a submerged entry nozzle during continuous casting. The negative effect of corundum in steel can be neutralized by its removal into the basic fluid slag formed in a ladle furnace unit by decreasing the activity of Al2O3. However, in practice, an excessive increase in the basicity of a refining slag to decrease the activity of Al2O3 is usually accompanied by slag heterogenization, an increase in the melting temperature of slag, and a decrease in its refining properties. The use of rare earth metal (REM) oxide additives can be a promising direction for decreasing the activity coefficient of Al2O3 in basic refining slags. The application of REM oxides ensures a decrease in their melting temperature, an increase in the fluidity, an increase in the sulfur distribution ratio, and a decrease in the REM distribution ratio. In this wok, we study the influence of cerium oxide in Ca–SiO2–Al2O3–MgO–Ce2O3 slags on NMIs. Experimental samples of clean steel held under a slag containing 15.0% cerium oxide exhibit the presence of up to 10 ppm cerium in the metal, a decrease in the total oxygen concentration to 13 ppm, a decrease in sulfur in the metal from 20 to 5 ppm, and the absence of manganese sulfide and corundum (Al2O3) NMIs. The Ce2O2S oxysulfide phase, magnesium and cerium oxide inclusions, and the MgO–Al2O3 oxide phase are also detected.
- 6 May 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (21) , 33332-33341
Design of CaO–8wt.%MgO–15 wt.%Al2O3–SiO2–Ce2O3-based refining slag: rheological behavior under the Ce2O3 content and CaO/SiO2 mass ratio increments
- 6 May 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (21) , 33332-33341
Design of CaO–8wt.%MgO–15 wt.%Al2O3–SiO2–Ce2O3-based refining slag: rheological behavior under the Ce2O3 content and CaO/SiO2 mass ratio increments
- 8 July 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (1) , 1-7
Equilibrium interphase distribution of chromium depending upon stainless steel slag temperature and basicity
- 8 July 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (1) , 1-7
Equilibrium interphase distribution of chromium depending upon stainless steel slag temperature and basicity
- Open Access
- 16 June 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (3) , 351-359
Thermodynamic modeling of interphase distribution of chromium and boron in slags of AOD reduction period
The paper presents the results of a thermodynamic modeling of the chromium and boron reduction from slags of reduction period of argon-oxygen decarburization (AOD) by a complex reducing agent containing silicon and aluminum. Using the simplex lattice method, an experiment planning matrix is constructed containing 16 compositions of the oxide system СаО – SiO2 – (3 – 6 %) В2О3 – 12 % Cr2O3 – 3 % Al2O3 – 8 % MgO of variable basicity 1.0 – 2.5. The results of thermodynamic modeling are graphically presented in form of dependence of equilibrium distribution of chromium and boron on the slag composition at temperatures of 1600 and 1700 °C. The constructed diagrams make it possible to quantify the influence of the temperature, basicity and B2O3 in the slag on equilibrium interphase distribution of chromium and boron. It is established that increasing the slag basicity from 1.0 to 2.5 improves the process of chromium reduction, but restores the boron stability. With an increase in B2O3 content in the slag, a slight deterioration of chromium reduction process occurs, while the boron content in the metal increases. With a simultaneous increase in basicity up to 2.5 and a decrease in boron oxide in the slag from 5 to 3 %, the interphase distribution coefficient of chromium is reduced to 1.5·10–3. Changing the process temperature from 1600 to 1700 °C does not have a negative effect on the process of chromium reduction, but worsens the boron reduction conditions. Based on analysis of the formed slag phases and thermodynamics of the reactions of their formation, it is established that chromium is mainly reduced by aliminum with only partial development of silicothermy. The residual silicon content reduces boron, thereby limiting its concentration in the metal. The results of high-temperature experiments showed high correspondence with the results of thermodynamic studies.
- 16 June 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (3) , 351-359
Open AccessThermodynamic modeling of interphase distribution of chromium and boron in slags of AOD reduction period
The paper presents the results of a thermodynamic modeling of the chromium and boron reduction from slags of reduction period of argon-oxygen decarburization (AOD) by a complex reducing agent containing silicon and aluminum. Using the simplex lattice method, an experiment planning matrix is constructed containing 16 compositions of the oxide system СаО – SiO2 – (3 – 6 %) В2О3 – 12 % Cr2O3 – 3 % Al2O3 – 8 % MgO of variable basicity 1.0 – 2.5. The results of thermodynamic modeling are graphically presented in form of dependence of equilibrium distribution of chromium and boron on the slag composition at temperatures of 1600 and 1700 °C. The constructed diagrams make it possible to quantify the influence of the temperature, basicity and B2O3 in the slag on equilibrium interphase distribution of chromium and boron. It is established that increasing the slag basicity from 1.0 to 2.5 improves the process of chromium reduction, but restores the boron stability. With an increase in B2O3 content in the slag, a slight deterioration of chromium reduction process occurs, while the boron content in the metal increases. With a simultaneous increase in basicity up to 2.5 and a decrease in boron oxide in the slag from 5 to 3 %, the interphase distribution coefficient of chromium is reduced to 1.5·10–3. Changing the process temperature from 1600 to 1700 °C does not have a negative effect on the process of chromium reduction, but worsens the boron reduction conditions. Based on analysis of the formed slag phases and thermodynamics of the reactions of their formation, it is established that chromium is mainly reduced by aliminum with only partial development of silicothermy. The residual silicon content reduces boron, thereby limiting its concentration in the metal. The results of high-temperature experiments showed high correspondence with the results of thermodynamic studies.
- 2 May 2024
- Published by Springer Nature in Metallurgist
- Vol. 67 (11-12) , 1-7
Structure and viscosity of slags containing cerium oxide
- 2 May 2024
- Published by Springer Nature in Metallurgist
- Vol. 67 (11-12) , 1-7
Structure and viscosity of slags containing cerium oxide
- Open Access
- 21 April 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (2) , 205-210
Effect of basicity on physical properties of ladle slags of CaO ‒ SiO2 ‒ Ce2O3 ‒ Al2O3 ‒ MgO system
The authors studied the physical properties of the slags of CaO ‒ SiO2 ‒ Al2O3 ‒ MgO system containing cerium oxide. The developed slags are based on a calcium silicate system, the basicity (CaO)/(SiO2) of which has a great influence on the slag properties. Generalization of the performed studies results allowed obtaining new data on the effect of basicity in cerium-containing slags of the studied oxide system on viscosity, temperature of crystallization onset and structure. Experimental studies of the physical properties of cerium-containing slags showed that with an increase in basicity of 2.0 ‒ 5.0, an increase in temperature of crystallization onset and viscosity is observed associated with structure of the formed slags. An increase in basicity from 2.0 to 5.0 contributes to an increase in viscosity from 0.20 to 0.41 Pa·s at 1500 °C and an increase in the crystallization temperature from 1397 to 1497 °C. The structural analysis showed that the structure of the cerium-containing slag is influenced by both the Si4+ ion and the Al3+ ion, which are grid-forming agents. Silicon ions in this system are present in the form of [SiO4 ]-tetrahedra, whereas aluminum ions are present in form of [AlO4]-tetrahedra and [AlO6]-octahedra. With an increase in basicity 2.0 to 2.5, the silicon structure becomes more complicated, and then at a basicity of 3.5 ‒ 5.0 it becomes simpler, whereas the aluminate one becomes more complicated due to an increase in the content of CaO, which participates in charge compensation of polymerized structural units [AlO4 ]-tetrahedra with the formation of a more stable tetrahedral structure, and as a result of increased slag viscosity. Slags of the studied oxide system containing 15 % Ce2O3 are characterized by a sufficiently high liquid mobility in the considered basicity range.
- 21 April 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (2) , 205-210
Open AccessEffect of basicity on physical properties of ladle slags of CaO ‒ SiO2 ‒ Ce2O3 ‒ Al2O3 ‒ MgO system
The authors studied the physical properties of the slags of CaO ‒ SiO2 ‒ Al2O3 ‒ MgO system containing cerium oxide. The developed slags are based on a calcium silicate system, the basicity (CaO)/(SiO2) of which has a great influence on the slag properties. Generalization of the performed studies results allowed obtaining new data on the effect of basicity in cerium-containing slags of the studied oxide system on viscosity, temperature of crystallization onset and structure. Experimental studies of the physical properties of cerium-containing slags showed that with an increase in basicity of 2.0 ‒ 5.0, an increase in temperature of crystallization onset and viscosity is observed associated with structure of the formed slags. An increase in basicity from 2.0 to 5.0 contributes to an increase in viscosity from 0.20 to 0.41 Pa·s at 1500 °C and an increase in the crystallization temperature from 1397 to 1497 °C. The structural analysis showed that the structure of the cerium-containing slag is influenced by both the Si4+ ion and the Al3+ ion, which are grid-forming agents. Silicon ions in this system are present in the form of [SiO4 ]-tetrahedra, whereas aluminum ions are present in form of [AlO4]-tetrahedra and [AlO6]-octahedra. With an increase in basicity 2.0 to 2.5, the silicon structure becomes more complicated, and then at a basicity of 3.5 ‒ 5.0 it becomes simpler, whereas the aluminate one becomes more complicated due to an increase in the content of CaO, which participates in charge compensation of polymerized structural units [AlO4 ]-tetrahedra with the formation of a more stable tetrahedral structure, and as a result of increased slag viscosity. Slags of the studied oxide system containing 15 % Ce2O3 are characterized by a sufficiently high liquid mobility in the considered basicity range.
- 8 January 2024
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2024 (1) , 85-90
Cerium Reduction by Aluminum and Calcium Carbide from Cerium-Containing Slags
—Under increasing requirements for the properties of steels, one of the ways to produce a high-quality product is microalloying with rare earth elements such as cerium, which can significantly influence the mechanical properties of steel even at low concentrations. To reduce the cost of steel, it is rational to introduce it into steel by direct reduction from oxide systems rather than by adding ferroalloys. To study this process, thermodynamic modeling of cerium reduction by aluminum and calcium carbide from slags of the CaO–SiO2–Ce2O3 system containing 15% Al2O3 and 8% MgO at temperatures of 1550 and 1650°C is carried out. The modeling is performed using the HSC 6.12 Chemistry (Outokumpu) software package based on Gibbs energy minimization using the simplex lattice planning method. The results of thermodynamic modeling are presented in the form of composition–property diagrams (equilibrium cerium content in a metal) for temperatures of 1550 and 1650°C. When metallic aluminum is used as a reducing agent, an increase in the slag basicity (CaO/SiO2) from 2 to 5 at a temperature of 1550°C leads to an increase in the equilibrium cerium content in the metal from 2 to 20 ppm in the concentration range 0–15% Ce2O3; that is, an increase in the slag basicity favorably affects the development of cerium reduction. An increase in metal temperature also exerts a positive effect on cerium reduction by aluminum. When the temperature increases to 1650°C, the equilibrium cerium content in the metal increases from 4 to 30 ppm in the concentration range 0–15% Ce2O3. The use of calcium carbide as a reducing agent leads to an increase in the cerium concentration in the metal to 30 and 40 ppm at 1550 and 1650°C, respectively, at a basicity of 5. The decisive role of slag basicity, cerium oxide concentration, and temperature factor in the development of cerium reduction by aluminum and calcium carbide has been confirmed.
- 8 January 2024
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2024 (1) , 85-90
Cerium Reduction by Aluminum and Calcium Carbide from Cerium-Containing Slags
—Under increasing requirements for the properties of steels, one of the ways to produce a high-quality product is microalloying with rare earth elements such as cerium, which can significantly influence the mechanical properties of steel even at low concentrations. To reduce the cost of steel, it is rational to introduce it into steel by direct reduction from oxide systems rather than by adding ferroalloys. To study this process, thermodynamic modeling of cerium reduction by aluminum and calcium carbide from slags of the CaO–SiO2–Ce2O3 system containing 15% Al2O3 and 8% MgO at temperatures of 1550 and 1650°C is carried out. The modeling is performed using the HSC 6.12 Chemistry (Outokumpu) software package based on Gibbs energy minimization using the simplex lattice planning method. The results of thermodynamic modeling are presented in the form of composition–property diagrams (equilibrium cerium content in a metal) for temperatures of 1550 and 1650°C. When metallic aluminum is used as a reducing agent, an increase in the slag basicity (CaO/SiO2) from 2 to 5 at a temperature of 1550°C leads to an increase in the equilibrium cerium content in the metal from 2 to 20 ppm in the concentration range 0–15% Ce2O3; that is, an increase in the slag basicity favorably affects the development of cerium reduction. An increase in metal temperature also exerts a positive effect on cerium reduction by aluminum. When the temperature increases to 1650°C, the equilibrium cerium content in the metal increases from 4 to 30 ppm in the concentration range 0–15% Ce2O3. The use of calcium carbide as a reducing agent leads to an increase in the cerium concentration in the metal to 30 and 40 ppm at 1550 and 1650°C, respectively, at a basicity of 5. The decisive role of slag basicity, cerium oxide concentration, and temperature factor in the development of cerium reduction by aluminum and calcium carbide has been confirmed.