MYMing Yang

Ming Yang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ming Yang has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Parameter Matching Principle for Dual-Rotor In-Wheel Motors via Coupling Effect Exploitation

    by Kehan Yan, Ming Yang, Zunyan Hu, Jianqiu Li, Liangfei Xu, Minggao Ouyang

    Single-mechanical-port dual-rotor motors (DRMs) represent a promising topology for next-generation electric machines (EMs). However, the optimal parameter-matching principle between the two rotors and the stator in radial-flux configurations has not been sufficiently explored due to geometric asymmetry. This article proposes a parameter-matching principle that explicitly exploits the magnetic coupling effect. By conceptually segregating the DRM into two equivalent single-rotor EMs, the proposed principle enables accurate identification of optimally matched DRM designs, independent of optimization history. Targeting in-wheel motor (IWM) applications, the influence of parameter matching on torque and loss is systematically analyzed in the torque–loss power design space. A set of effective matching conditions are then formulated based on coupling-related geometric metrics. Additional influencing factors, including operating condition fluctuations and core material variations, are also investigated. Results reveal that the effective matching envelope primarily occupies the central region of the Pareto front rather than covering all Pareto-optimal designs. This highlights the necessity of coupling-based selection to avoid arbitrary choices from Pareto fronts. Finally, an automotive-grade DRM prototype designed under the proposed principle was fabricated and experimentally validated, achieving a peak torque exceeding 1500 Nm and a maximum efficiency above 92%, confirming the effectiveness of the proposed principle.


  • Generalized Fixed-Point Iteration Technique for Solving Magnetic Hysteresis Problems

    by Jiatong Yin, Shuaichao Yue, Yongjian Li, Ming Yang, Jingming Gao, Kangshuo Qin

    Accurate simulation of the electromagnetic field in iron cores requires accounting for the hysteresis behavior of magnetic materials, which imposes higher requirements on the robustness and efficiency of nonlinear solvers. This paper first discusses the deficiencies of existing fixed-point (FP) methods in magnetic field computation involving hysteresis media. Then, a generalized FP iteration technique for multi-valued nonlinear problems is proposed, featuring a modified formula for conditioning FP coefficient and a numerical approach for estimating the differential reluctivity. Time-stepping finite element analysis (FEA) of a synchronous motor is performed where the ferromagnetic material is characterized by three representative hysteresis models. The proposed solution technique demonstrates remarkable performance on adaptability and convergence rate compared with Newton-Raphson (NR) methods and traditional FP methods. Additionally, experimental results from a motor prototype validate the effectiveness of the numerical simulation.


  • Open Access

    Comprehensive investigation on high-frequency rotational magnetic properties of core materials for high-speed motors

    by Ming Yang, Yongjian Li, Shuaichao Yue, Zunyan Hu, Jianqiu Li, Qingxin Yang, Minggao Ouyang

    In this paper, the rotational magnetic properties of ultra-thin non-oriented silicon steel ST100 (200 Hz - 5 kHz) are measured by the novel two-dimensional magnetic property tester, with nanocrystalline alloy 1K107B (1 kHz - 20 kHz) serving as a reference. The anisotropy behavior of these materials under varying flux densities is analyzed based on the experimental results. The change in anisotropy under circular magnetization is explained by comparing the B-H phase difference at different flux densities and frequencies. Taking the elliptical magnetization of ST100 at 1 kHz as a case study, the magnetic properties of materials with different levels of rotational magnetization are systematically investigated. By comparing the phase difference of B-H loci and the harmonic content of H at different axial ratios and flux densities, the factors contributing to the nonlinear behavior of rotational magnetization are identified. Additionally, the variation in core loss under different rotational conditions is analyzed. It can provide theoretical and data support for the magnetic structure design and loss evaluation in the high-speed motor.

  • Small power litz wire ferrite inductor loss model based on neural network

    by Huizhong Sun, Ming Yang, Zhihao Lin, Ning Wang, Ariya Sangwongwanich, Huai Wang

    Several kilowatt litz wire inductor has wide application, including automotive, renewable energy, household power supply, etc., which has a promising market for the next ten years. The traditional method of inductor loss calculation is a compromise between simplicity and accuracy. For example, iGSE (improved generalized Steinmetz equation) is commonly seen in core loss calculation, and the Dowell equation is commonly seen in high-frequency winding loss calculation. However, these methods, although simple and clear in the calculation, are not accurate. A neural network has been proven a powerful tool for modeling. In this paper, the authors try to model the inductor loss – core and winding loss – in a neural network approach. For core loss, Magnets dataset and three layers neural networks are used. Because magnetic bias is not included in the dataset, this model is only suitable when bias is absent. For winding loss, the sequence-to-sequence transformer network is introduced. The results show much-improved accuracy but with increased calculation complexity. So this neural network approach is suitable for higher accuracy design. Finally, the authors open-sourced the inductor loss code. Users just need to provide the necessary design parameters and working points to get inductor loss in their design.


  • Application-Oriented Characterization and Analysis of Core Materials Under Medium-Frequency Condition

    by Ming Yang, Qingxin Yang, Yongjian Li, Zhiwei Lin, Shuaichao Yue, Huai Wang, Amir Sajjad Bahman

    In medium-frequency applications, magnetic components generally operate in high-temperature conditions caused by higher power loss and more difficult heat dissipation, which results in changes in their electromagnetic characteristics. In this article, the application-oriented characterization of the typical core materials, Mn-Zn ferrite and Fe-based nanocrystalline alloy, is comprehensively studied. The magnetic parameters under sinusoidal (5–50 kHz) and square (10 kHz) excitation from 20 °C to 125 °C are analyzed detailedly. Combined with the micromagnetic theory, the influence factors of electromagnetic parameters such as permeability and power factor angle are investigated. The loss variation of ferrite with temperature, flux density, and frequency is explained by using the energy loss ratio. The proportion of P h and P dy in total loss with temperature and frequency is compared, and the loss fluctuation of nanocrystalline alloys and ferrite is analyzed. Moreover, the reasonable range of frequency that needs to consider temperature effect in practical applications is suggested. The difference between the B - H loop bias under asymmetrical square excitation and dc bias conditions is compared and illuminated. The effectiveness and limitation of typical Steinmetz equations considering the temperature and duty cycle effect are analyzed, and the suggestion of loss calculation is given combined with the material characteristics.


  • Open Access

    Magnetic property measurement and analysis of high-frequency soft magnetic materials under non-sinusoidal excitation considering temperature effect

    by Yongjian Li, Chuhao Jin, Ming Yang, Shenghui Mu, Changgeng Zhang

    Electrical equipment operates under various temperatures and non-sinusoidal excitation, which makes magnetic properties of soft magnetic materials quite different from those under room temperature and sinusoidal excitation. Magnetic properties and loss characteristics of the ferrite (N87) and nanocrystalline alloy (FT-3KL) are measured and analyzed in the range of 25 °C to 125 °C from 5 kHz to 20 kHz under both square and rectangular excitation with different duty ratios. The temperature dependence of these materials under different conditions is systematically compared with normalization method. The comprehensive performance of core materials is discussed in combination with the experimental phenomena and results.


  • Open Access

    Core loss measurement and comparative analysis for soft magnetic materials under complex non-sinusoidal excitations

    by Yongjian Li, Shenghui Mu, Changgeng Zhang, Ming Yang

    With the advancement of wide-bandgap power devices, the power electronics equipment is developing toward higher switching frequencies and more complex switching modes in recent years. Accurate prediction of the core loss for magnetic components has been emphasized as the excitations of magnetic materials varying depending on the operating mode of the power supplies. Therefore, this paper presents the results of an extensive core loss study performed on nanocrystalline alloy (FT-3KL), amorphous alloy (1K101) and ultra-thin oriented silicon steel (GT-50). Firstly, an automatic setup for core loss measurement of soft magnetic materials fed by a full-bridge inverter based on silicon carbide (SiC) MOSFET is proposed. Then, the effects of switching oscillations from the inverter and the characteristic parameters of complex non-sinusoidal excitations on the core loss are analyzed comparatively. The core loss shows different regular distributions with the change of each characteristic parameter of excitations respectively. However, the regular distributions will be influenced by the high-frequency switching oscillations, which makes the prediction of core loss more complicated. This paper can provide a reference for the development of high-precision core loss model and performance optimization of power electronics equipment.


  • Open Access

    The 3-D vector hysteresis model of SMC materials based on the SAE and play operator

    by Yangyang Ma, Yongjian Li, Yu Dou, Mingyu Yue, Ming Yang

    The hysteresis modeling of ferromagnetic materials in electrical equipment is one of the basic theoretical studies in the field of electrical engineering. In this paper, a 3-D vector hysteresis model is proposed based on Stacked Auto-Encoder (SAE) model and hysteresis operator space theory. Multiple 3-D vector Play hysteresis operators are used to construct an hysteresis operator space to create the high-dimensional operator data. By the operator space, the nonlinear hysteresis relationship in the hysteresis data is transformed into a nonlinear mapping between the operator data and the output of the model. And the SAE model is used to characterize this nonlinear mapping. In the training of the SAE model, training set is composed of operator data and magnetic field strength data. The structure of the vector hysteresis model is determined by taking the output of the operator space as the input of the SAE model. The simulation results show that the model can effectively describe the nonlinear characteristics and anisotropic of the Soft Magnetic Composite under 3-D vector excitation. In addition, this model has certain generalization ability.

  • Temperature Dependence of Powder Cores Magnetic Properties for Medium-Frequency Applications

    by Wenting Zhang, Qingxin Yang, Yongjian Li, Zhiwei Lin, Ming Yang

    Soft magnetic powder cores are attractive because of their loss at medium frequency. However, the performance of electrical equipment is affected by temperature increase by the heat of core losses. In this article, the magnetic properties of nanocrystalline powder core, amorphous powder core, X-Flux (Fe-Si), Sendust (Fe-Si-Al), and ferrite are measured and compared in the range of 25 °C–125 °C from 20 to 100 kHz. The discussed magnetic properties include the temperature-dependent coercive field, initial permeability, inductance factor, saturation flux density, and core loss. The results show that magnetic properties depend on temperature and frequency. In comparison, the nanocrystalline powder core has the best temperature stability and relatively low core loss among the five materials, so it can be well used at broad temperature and medium frequency.


  • Comprehensive Analysis of Nanocrystalline Ribbon Cores in High-Power-Density Wireless Power Transfer Pads for Electric Vehicles

    by Wenting Zhang, Qingxin Yang, Yongjian Li, Zhiwei Lin, Ming Yang, Mingfa Mi

    The nanocrystalline alloys are gradually used as shielding materials in wireless power transfer (WPT) systems with the development of high power density. In this article, the system properties of WPT using ferrite and four types of nanocrystalline cores are simulated by 3-D finite element analysis (FEA). Based on this, a novel shielding pad composed of nanocrystalline alloy and ferrite is designed to improve the WPT system properties. The WPT systems are preliminarily compared with 3-D FEA when the different nanocrystalline alloys are used in the novel shielding pad. The experimental WPT system for 85 kHz and 1.5 kW with a 24 cm air gap between the primary and secondary coils is built to validate the simulation. The results show that significantly greater shielding can be realized for the novel pad at the price of a slight decrease of transmission efficiency than conventional ferrite core.