Alexey Nikolaevich Ryabinkin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexey Nikolaevich Ryabinkin has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
A O Serov
5 shared publications- Alexander F. Pal
Skobeltsyn Institute for Nuclear Physics of the Lomonosov Moscow State University, Leninskiye Gory 1, Moscow 119899, Russia
5 shared publications - Alexander O. Serov
Skobeltsyn Institute for Nuclear Physics of the Lomonosov Moscow State University, Leninskiye Gory 1, Moscow 119899, Russia
5 shared publications Yu A Mankelevich
Skobeltsyn Institute of Nuclear Physics, Lomonosov Moscow State University Skobeltsyn Institute of Nuclear Physics, Moskva, Moskva, RUSSIAN FEDERATION
4 shared publicationsA F Pal
State Research Center of the Russian Federation—Troitsk Institute for Innovation and Fusion Research, Pushkovykh Street 12, Troitsk, Moscow 108840, Russia
3 shared publicationsA T Rakhimov
2 shared publications
Latest Publications
- 22 January 2024
- Published by Wiley in Plasma Processes and Polymers
- Vol. 21 (5)
Challenges in scaling of IPVD deposited Ta barriers on OSG low‐k films: Carbonization of Ta by CHx radicals generated through VUV‐induced decomposition of carbon‐containing groups
The effect of vacuum ultraviolet (VUV) radiation during ionized physical vapor deposition (IPVD) of tantalum barriers on various porous organosilicate glass low‐k SiCOH films is studied using advanced diagnostics and quantum chemical calculations. VUV photons break the Si–C bonds, releasing hydrocarbon radicals from the pore surfaces. These radicals, trapped in pores that are partially sealed by tantalum deposition, can either react with tantalum to form carbide‐like compounds, TaCx, or be redeposited in the pores as CHx polymers. This is evidenced by a decrease in CH3 groups that correlates with an increase in TaCx. The formation of TaCx poses a significant challenge in the back end of line (BEOL) technology when reducing the barrier thickness.
- 22 January 2024
- Published by Wiley in Plasma Processes and Polymers
- Vol. 21 (5)
Challenges in scaling of IPVD deposited Ta barriers on OSG low‐k films: Carbonization of Ta by CHx radicals generated through VUV‐induced decomposition of carbon‐containing groups
The effect of vacuum ultraviolet (VUV) radiation during ionized physical vapor deposition (IPVD) of tantalum barriers on various porous organosilicate glass low‐k SiCOH films is studied using advanced diagnostics and quantum chemical calculations. VUV photons break the Si–C bonds, releasing hydrocarbon radicals from the pore surfaces. These radicals, trapped in pores that are partially sealed by tantalum deposition, can either react with tantalum to form carbide‐like compounds, TaCx, or be redeposited in the pores as CHx polymers. This is evidenced by a decrease in CH3 groups that correlates with an increase in TaCx. The formation of TaCx poses a significant challenge in the back end of line (BEOL) technology when reducing the barrier thickness.
- 22 December 2022
- Published by Wiley in Plasma Processes and Polymers
- Vol. 20 (4)
Damage to OSG low‐k films during IPVD deposition of the Ta barrier layer
The degradation of a porous organosilicate glass low‐k dielectric during the ionized physical vapor deposition of tantalum coating is studied. The main contribution to the damage is made by vacuum UV flux (1014–1015 s–1 cm–2) from the argon inductively coupled plasma of the ionizer, and the effect of the direct current magnetron sputter plasma is small. The damage by vacuum ultraviolet photons with an energy exceeding the band gap of the SiO2 matrix is associated not only with the removal of carbon‐containing groups (terminal CH3 and bridging CH2) but also with the breaking of Si–O bonds in the Si–O–Si matrix followed by the formation of hydrophilic Si–OH and Si–H groups. Consequently, the degree of damage can be much higher than would be expected from the depth of CH3 group depletion.
- 22 December 2022
- Published by Wiley in Plasma Processes and Polymers
- Vol. 20 (4)
Damage to OSG low‐k films during IPVD deposition of the Ta barrier layer
The degradation of a porous organosilicate glass low‐k dielectric during the ionized physical vapor deposition of tantalum coating is studied. The main contribution to the damage is made by vacuum UV flux (1014–1015 s–1 cm–2) from the argon inductively coupled plasma of the ionizer, and the effect of the direct current magnetron sputter plasma is small. The damage by vacuum ultraviolet photons with an energy exceeding the band gap of the SiO2 matrix is associated not only with the removal of carbon‐containing groups (terminal CH3 and bridging CH2) but also with the breaking of Si–O bonds in the Si–O–Si matrix followed by the formation of hydrophilic Si–OH and Si–H groups. Consequently, the degree of damage can be much higher than would be expected from the depth of CH3 group depletion.
- 1 May 2021
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 30 (5) , 055009
Structure of DC magnetron sputtering discharge at various gas pressures: a two-dimensional particle-in-cell Monte Carlo collision study
We report the results of a particle-in-cell Monte-Carlo collision simulation of an axially symmetric DC magnetron discharge with a 5 cm diameter flat cathode in argon at pressures from 1 to 10 mTorr at a constant discharge current of about 0.5 A. Calculations show that the cathode region, where almost the entire discharge voltage drops, consists of a cathode sheath 0.1–0.2 mm wide and a presheath about 2 cm wide, where most of the ionizations occur, separated by a region 0.25–0.35 mm wide, where the plasma potential remains almost unchanged and the plasma density reaches its maximum value. Most of the discharge voltage drops in the presheath at low gas pressure, and in cathode sheath at high pressure. The ratio of sheath to presheath voltages increases linearly with pressure. The distribution of the ionization rate has two maxima: near the cathode sheath and in the presheath. The fraction of ionizations near the cathode sheath increases with pressure. The electron energy distribution function (EEDF) is generally a two-temperature function. At low pressures at a distance of less than 1 cm from the cathode, the EEDF becomes one-temperature. A high-energy tail is observed on the EEDF near the cathode; the fraction of electrons in the tail (in the order of tenths of a percent at 10 mTorr) and their energy, determined by the sheath voltage, increase with pressure. The electron temperature decreases with pressure due to a decrease of the electric field in the presheath, which leads to a decrease of energetically accessible regions of collisionless electron motion and to a corresponding decrease in the energy that electrons can obtain in these regions. The dependence of the discharge voltage on the gas pressure has a minimum at about 3 mTorr, which occurs due to the competition of two processes on pressure increase: a decrease in the electron temperature and a decrease in the fraction of electrons returning back to the cathode. Plasma density waves are observed in the presheath region at pressures of 1–3 mTorr.
- 1 May 2021
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 30 (5) , 055009
Structure of DC magnetron sputtering discharge at various gas pressures: a two-dimensional particle-in-cell Monte Carlo collision study
We report the results of a particle-in-cell Monte-Carlo collision simulation of an axially symmetric DC magnetron discharge with a 5 cm diameter flat cathode in argon at pressures from 1 to 10 mTorr at a constant discharge current of about 0.5 A. Calculations show that the cathode region, where almost the entire discharge voltage drops, consists of a cathode sheath 0.1–0.2 mm wide and a presheath about 2 cm wide, where most of the ionizations occur, separated by a region 0.25–0.35 mm wide, where the plasma potential remains almost unchanged and the plasma density reaches its maximum value. Most of the discharge voltage drops in the presheath at low gas pressure, and in cathode sheath at high pressure. The ratio of sheath to presheath voltages increases linearly with pressure. The distribution of the ionization rate has two maxima: near the cathode sheath and in the presheath. The fraction of ionizations near the cathode sheath increases with pressure. The electron energy distribution function (EEDF) is generally a two-temperature function. At low pressures at a distance of less than 1 cm from the cathode, the EEDF becomes one-temperature. A high-energy tail is observed on the EEDF near the cathode; the fraction of electrons in the tail (in the order of tenths of a percent at 10 mTorr) and their energy, determined by the sheath voltage, increase with pressure. The electron temperature decreases with pressure due to a decrease of the electric field in the presheath, which leads to a decrease of energetically accessible regions of collisionless electron motion and to a corresponding decrease in the energy that electrons can obtain in these regions. The dependence of the discharge voltage on the gas pressure has a minimum at about 3 mTorr, which occurs due to the competition of two processes on pressure increase: a decrease in the electron temperature and a decrease in the fraction of electrons returning back to the cathode. Plasma density waves are observed in the presheath region at pressures of 1–3 mTorr.
- 1 July 2020
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 46 (7) , 725-728
The Influence of Magnetron Sputtering Conditions on the Structure of Zr–Pd Coatings
Using the method of DC magnetron sputtering, nonstructured amorphous metal coatings of Zr75Pd25 composition were obtained with an average deposition rate of 1.3 nm/s at a substrate temperature of 40°C, while crystalline coatings were formed at a higher substrate temperature. A crystalline coating with equilibrium phase composition was obtained at 350°C. Coatings deposited at intermediate temperatures contained predominantly a PdZr phase, in contrast to the equilibrium PdZr2 phase. The surface roughness of amorphous coatings was on a level of 0.2–0.5 nm, which was about ten times lower than the mean roughness of crystalline coatings with the same composition.
- 1 July 2020
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 46 (7) , 725-728
The Influence of Magnetron Sputtering Conditions on the Structure of Zr–Pd Coatings
Using the method of DC magnetron sputtering, nonstructured amorphous metal coatings of Zr75Pd25 composition were obtained with an average deposition rate of 1.3 nm/s at a substrate temperature of 40°C, while crystalline coatings were formed at a higher substrate temperature. A crystalline coating with equilibrium phase composition was obtained at 350°C. Coatings deposited at intermediate temperatures contained predominantly a PdZr phase, in contrast to the equilibrium PdZr2 phase. The surface roughness of amorphous coatings was on a level of 0.2–0.5 nm, which was about ten times lower than the mean roughness of crystalline coatings with the same composition.
- 20 May 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 53 (29) , 295202
VUV radiation flux from argon DC magnetron plasma
Vacuum ultraviolet (VUV) flux of argon plasma radiation in a DC magnetron discharge with a plane circular titanium cathode is measured. It is found that the intensity of VUV radiation, mainly indicated by the resonance lines of argon atoms at 104.8 and 106.7 nm and ions at 92 and 93.2 nm, is proportional to the discharge current and decreases with pressure. Following the results of the measurements, a numerical model of resonance radiation transport is developed to determine the VUV flux to the substrate placed near the sputtering cathode where direct measurements are impossible due to the fast contamination of the detector by sputtered atoms. In the case of a substrate located 10 cm opposite the cathode surface, the upper limit of estimated VUV flux is of the order of 10 15 photons cm −2 s −1 at a coating deposition rate of 1.5 nm s −1 for 2 and 12 mTorr gas pressures. Based on the measurements, the damage to a porous low- k dielectric by VUV radiation during the deposition of barrier layers in the DC magnetron discharge is first estimated.
- 20 May 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 53 (29) , 295202
VUV radiation flux from argon DC magnetron plasma
Vacuum ultraviolet (VUV) flux of argon plasma radiation in a DC magnetron discharge with a plane circular titanium cathode is measured. It is found that the intensity of VUV radiation, mainly indicated by the resonance lines of argon atoms at 104.8 and 106.7 nm and ions at 92 and 93.2 nm, is proportional to the discharge current and decreases with pressure. Following the results of the measurements, a numerical model of resonance radiation transport is developed to determine the VUV flux to the substrate placed near the sputtering cathode where direct measurements are impossible due to the fast contamination of the detector by sputtered atoms. In the case of a substrate located 10 cm opposite the cathode surface, the upper limit of estimated VUV flux is of the order of 10 15 photons cm −2 s −1 at a coating deposition rate of 1.5 nm s −1 for 2 and 12 mTorr gas pressures. Based on the measurements, the damage to a porous low- k dielectric by VUV radiation during the deposition of barrier layers in the DC magnetron discharge is first estimated.
- Open Access
- 18 January 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1147 (1) , 012115
Correlation between plasma glow intensity distribution and sputtering profile in dc magnetron discharge
The correlation between the plasma glow intensity distribution and the target sputtering profile in an axially symmetric unbalanced dc magnetron discharge with copper cathode in argon is studied. At high pressures the argon atom and ion emission intensities are in good agreement with a sputtering profile. In case of low pressures, a satisfactory agreement is only for the ion emission. The best estimates of the sputtering profile can be obtained from the argon ion emission distribution at not too low pressures.
- 18 January 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1147 (1) , 012115
Open AccessCorrelation between plasma glow intensity distribution and sputtering profile in dc magnetron discharge
The correlation between the plasma glow intensity distribution and the target sputtering profile in an axially symmetric unbalanced dc magnetron discharge with copper cathode in argon is studied. At high pressures the argon atom and ion emission intensities are in good agreement with a sputtering profile. In case of low pressures, a satisfactory agreement is only for the ion emission. The best estimates of the sputtering profile can be obtained from the argon ion emission distribution at not too low pressures.
- Open Access
- 1 January 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 946 (1) , 012150
Effect of interelectrode distance on dc magnetron current–pressure characteristics
The current–pressure (I–P) non-monotonic characteristic in the magnetron discharge dc in argon at different interelectrode distances was investigated. The ion spatial distribution was obtained with optical emission spectroscopy and the characteristic dimensions of the discharge structure in near cathode region were determined. It is shown that decreasing the distance between electrodes does not affect the shape and position of the nonmonotonic part of I–P characteristic until this distance become comparable with the dimensions of the ionization region near cathode. The existence of non-monotonic part of I–P characteristic is determined by the processes in the near cathode region and is probably unrelated with the cold electron transfer in the rest of the plasma.
- 1 January 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 946 (1) , 012150
Open AccessEffect of interelectrode distance on dc magnetron current–pressure characteristics
The current–pressure (I–P) non-monotonic characteristic in the magnetron discharge dc in argon at different interelectrode distances was investigated. The ion spatial distribution was obtained with optical emission spectroscopy and the characteristic dimensions of the discharge structure in near cathode region were determined. It is shown that decreasing the distance between electrodes does not affect the shape and position of the nonmonotonic part of I–P characteristic until this distance become comparable with the dimensions of the ionization region near cathode. The existence of non-monotonic part of I–P characteristic is determined by the processes in the near cathode region and is probably unrelated with the cold electron transfer in the rest of the plasma.
- Open Access
- 27 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 774 (1) , 012150
Current–pressure dependencies of dc magnetron discharge in inert gases
The current-pressure (I-P) characteristics of dc magnetron discharge in inert gases (Ar, Kr and Xe) for various constant discharge voltages were measured. Under certain conditions on I-P characteristic, the nonmonotonic region of local maximum followed by a minimum is observed. It is found that increasing mass of the working gas ions results in a shift of the local maximum to lower pressures. The spatial distribution of ions in the plasma was studied by optical emission spectroscopy. Transformation of the discharge spatial structure with pressure was observed. A qualitative model of the observed trends is presented. It takes into account the pressure dependence of the discharge spatial structure, the capturing of secondary electrons by the cathode and charge exchange effects.
- 27 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 774 (1) , 012150
Open AccessCurrent–pressure dependencies of dc magnetron discharge in inert gases
The current-pressure (I-P) characteristics of dc magnetron discharge in inert gases (Ar, Kr and Xe) for various constant discharge voltages were measured. Under certain conditions on I-P characteristic, the nonmonotonic region of local maximum followed by a minimum is observed. It is found that increasing mass of the working gas ions results in a shift of the local maximum to lower pressures. The spatial distribution of ions in the plasma was studied by optical emission spectroscopy. Transformation of the discharge spatial structure with pressure was observed. A qualitative model of the observed trends is presented. It takes into account the pressure dependence of the discharge spatial structure, the capturing of secondary electrons by the cathode and charge exchange effects.
- 1 May 2015
- Published by Pleiades Publishing Ltd in Russian Journal of General Chemistry
- Vol. 85 (5) , 1270-1283
Application of dusty plasma for production of disperse composite materials
Objectives and achievements of the production of disperse composite materials (DCMs) which consist of particles with a metal coating are represented. The prospects of the DCM production by the dusty...
- 1 May 2015
- Published by Pleiades Publishing Ltd in Russian Journal of General Chemistry
- Vol. 85 (5) , 1270-1283
Application of dusty plasma for production of disperse composite materials
Objectives and achievements of the production of disperse composite materials (DCMs) which consist of particles with a metal coating are represented. The prospects of the DCM production by the dusty...
- 1 January 2013
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 39 (1) , 39-41
Equirate magnetron sputtering of mosaic copper-graphite targets
Based on experimental data on sputtering of copper-graphite cathodes, we propose a mechanism of equirate sputtering of elements of mosaic targets prepared from materials the sputtering yields of which differ by almost an order of magnitude. The mechanism takes into account the occurrence of a height discontinuity between the mosaic elements at the initial stage of sputtering, the redistribution of ion fluxes between the elements, and the effects related to the mass transfer in plasma and the implantation of sputtered atoms into the mosaic elements of the different variety.
- 1 January 2013
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 39 (1) , 39-41
Equirate magnetron sputtering of mosaic copper-graphite targets
Based on experimental data on sputtering of copper-graphite cathodes, we propose a mechanism of equirate sputtering of elements of mosaic targets prepared from materials the sputtering yields of which differ by almost an order of magnitude. The mechanism takes into account the occurrence of a height discontinuity between the mosaic elements at the initial stage of sputtering, the redistribution of ion fluxes between the elements, and the effects related to the mass transfer in plasma and the implantation of sputtered atoms into the mosaic elements of the different variety.