Andreas Bogner
Research Subjects
Andreas Bogner has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Frank Dehn
Karlsruhe Institute of Technology (KIT)
4 shared publications - Astrid Hirsch
Institute of Concrete Structures and Building Materials, Department Building Materials and Concrete Construction, Karlsruhe Institute of Technology (KIT), 76131 Karlsruhe, Germany
1 shared publication - David Alós Shepherd
Karlsruher Institut für Technologie Materialprüfungs‐ und Forschungsanstalt Karlsruhe (MPA Karlsruhe) Gotthard‐Franz‐Straße 3 76131 Karlsruhe
1 shared publication - Eduardus Koenders
Institute of Construction and Building Materials Technical University of Darmstadt Darmstadt Germany
1 shared publication - Engin Kotan
Karlsruhe Institute of Technology (KIT), Institute of Concrete Structures and Building Materials (IMB), Materials Testing and Research Institute, Gotthard-Franz-Straße 3, 76131 Karlsruhe, Germany
1 shared publication - Felix Berger
Institute of Construction and Building Materials, Technical University of Darmstadt, 64287 Darmstadt, Germany
1 shared publication
Latest Publications
- Open Access
- 10 March 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (1) , 14
The Time Development of the Microstructural Properties of Plastic Concrete: Material Insights and Experimental Boundaries
Plastic Concrete is a low-strength ( ≤ 1.0 MPa), low-stiffness impervious concrete used for cut-off walls in earthen dams worldwide. These properties are achieved through a very high w/c ratio (w/c ≥ 3.0) and water-binding additions (e.g., bentonite). To date, the effect of mix design, especially w/c ratio, as well as bentonite content and type, on the long-term time development of the microstructural properties and corresponding compressive strength of Plastic Concrete has yet to be systematically studied. Furthermore, in the literature, mercury intrusion porosimetry (MIP) and X-ray diffractometry (XRD) have yet to be applied systematically to Plastic Concrete for this purpose. The present study closes this gap. Ten Plastic Concrete mixes with two bentonite–cement ratios, three types of sodium bentonite and two swelling times were produced. MIP and XRD measurements and compressive strength tests were performed at sample ages of 7 d, 28 d, 56 d, 91 d and four years. The results show that both MIP and XRD can be successfully used; however, meticulous sample preparation and data analysis must be considered. The porosimetry results show a bi-modal pore size distribution, with two age-dependent peaks at approximately 10,000–20,000 nm and 100–700 nm. The results also exhibit a clear pore refinement over time, with coarse porosity dropping from 26% to 15% over four years. In addition, the fine porosity peak is significantly refined over time and positively correlates with the significant increase in compressive strength. The XRD results show no unexpected crystalline phases over the same period. Overall, this study links MIP and corresponding compressive strength data specifically for Plastic Concrete for the first time, confirming the key role that the mix design of Plastic Concrete plays in defining its long-term microstructural and mechanical properties and ensuring more realistic cut-off wall design in the future. In addition, the experimental boundaries for MIP testing on Plastic Concrete are set out for the first time, enabling future research in this field.- 10 March 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (1) , 14
Open AccessThe Time Development of the Microstructural Properties of Plastic Concrete: Material Insights and Experimental Boundaries
Plastic Concrete is a low-strength ( ≤ 1.0 MPa), low-stiffness impervious concrete used for cut-off walls in earthen dams worldwide. These properties are achieved through a very high w/c ratio (w/c ≥ 3.0) and water-binding additions (e.g., bentonite). To date, the effect of mix design, especially w/c ratio, as well as bentonite content and type, on the long-term time development of the microstructural properties and corresponding compressive strength of Plastic Concrete has yet to be systematically studied. Furthermore, in the literature, mercury intrusion porosimetry (MIP) and X-ray diffractometry (XRD) have yet to be applied systematically to Plastic Concrete for this purpose. The present study closes this gap. Ten Plastic Concrete mixes with two bentonite–cement ratios, three types of sodium bentonite and two swelling times were produced. MIP and XRD measurements and compressive strength tests were performed at sample ages of 7 d, 28 d, 56 d, 91 d and four years. The results show that both MIP and XRD can be successfully used; however, meticulous sample preparation and data analysis must be considered. The porosimetry results show a bi-modal pore size distribution, with two age-dependent peaks at approximately 10,000–20,000 nm and 100–700 nm. The results also exhibit a clear pore refinement over time, with coarse porosity dropping from 26% to 15% over four years. In addition, the fine porosity peak is significantly refined over time and positively correlates with the significant increase in compressive strength. The XRD results show no unexpected crystalline phases over the same period. Overall, this study links MIP and corresponding compressive strength data specifically for Plastic Concrete for the first time, confirming the key role that the mix design of Plastic Concrete plays in defining its long-term microstructural and mechanical properties and ensuring more realistic cut-off wall design in the future. In addition, the experimental boundaries for MIP testing on Plastic Concrete are set out for the first time, enabling future research in this field. - Open Access
- 19 June 2024
- Published by Royal Society of Chemistry (RSC) in RSC Sustainability
- Vol. 2 (8) , 2092-2124
Surface treatments on concrete: an overview on organic, inorganic and nano-based coatings and an outlook about surface modification by rare-earth oxides
Cementitious construction materials like concrete stand as pivotal constituents in the respective industry owing to their wide-ranging benefits in terms of abundant raw material sources, ease of processing, versatile usability, exceptional material properties, durability, and cost-effectiveness. Nonetheless, the production of cement is associated with substantial carbon dioxide (CO2) emissions, thereby contributing significantly to global greenhouse gas levels. This conundrum underscores the pressing need for innovative solutions that can mitigate the environmental impact while preserving the indispensable attributes of cementitious construction materials. This review article delves into the realm of surface treatments as a promising avenue to augment the service life and sustainability of concrete structures. The primary objective of using coating technologies is to curtail the overconsumption of cement and natural resources – such as water, sand, and gravel – by extending the longevity of cementitious construction materials, which contributes to an alleviation in the environmental footprint of cement production and, subsequently, to a reduction in global anthropogenic CO2 emissions. In this comprehensive study, we discuss three distinct types of established surface coating: (1) organic coatings, (2) coatings based on nanomaterials like graphene, and (3) inorganic coatings. Through a systematic examination of these approaches, we elucidate their mechanisms of protection, highlighting their potential to enhance the durability, resistance to environmental stressors, and overall performance of cementitious construction materials. Based on a comprehensive literature review, we compare the performance of these surface treatments in terms of protecting different cementitious surfaces against different degradation scenarios. Finally, we give an outlook on new innovative approaches for the protection of cementitious surfaces, including the presentation of the concept of incorporating rare earth metal ions into the surface of cementitious construction materials. This could potentially combine the advantages of organic and inorganic surface treatments as well as integral waterproofing.
- 19 June 2024
- Published by Royal Society of Chemistry (RSC) in RSC Sustainability
- Vol. 2 (8) , 2092-2124
Open AccessSurface treatments on concrete: an overview on organic, inorganic and nano-based coatings and an outlook about surface modification by rare-earth oxides
Cementitious construction materials like concrete stand as pivotal constituents in the respective industry owing to their wide-ranging benefits in terms of abundant raw material sources, ease of processing, versatile usability, exceptional material properties, durability, and cost-effectiveness. Nonetheless, the production of cement is associated with substantial carbon dioxide (CO2) emissions, thereby contributing significantly to global greenhouse gas levels. This conundrum underscores the pressing need for innovative solutions that can mitigate the environmental impact while preserving the indispensable attributes of cementitious construction materials. This review article delves into the realm of surface treatments as a promising avenue to augment the service life and sustainability of concrete structures. The primary objective of using coating technologies is to curtail the overconsumption of cement and natural resources – such as water, sand, and gravel – by extending the longevity of cementitious construction materials, which contributes to an alleviation in the environmental footprint of cement production and, subsequently, to a reduction in global anthropogenic CO2 emissions. In this comprehensive study, we discuss three distinct types of established surface coating: (1) organic coatings, (2) coatings based on nanomaterials like graphene, and (3) inorganic coatings. Through a systematic examination of these approaches, we elucidate their mechanisms of protection, highlighting their potential to enhance the durability, resistance to environmental stressors, and overall performance of cementitious construction materials. Based on a comprehensive literature review, we compare the performance of these surface treatments in terms of protecting different cementitious surfaces against different degradation scenarios. Finally, we give an outlook on new innovative approaches for the protection of cementitious surfaces, including the presentation of the concept of incorporating rare earth metal ions into the surface of cementitious construction materials. This could potentially combine the advantages of organic and inorganic surface treatments as well as integral waterproofing.
- Open Access
Systematic Experimental Investigation into the Determination of Micromechanical Properties of Hardened Cement Paste Using Nanoindentation—Opportunities and Limitations
The nanoindentation technique is already widely applied in the mechanical characterization of the microstructure of thin films with respect to different materials. Generally, by means of nanoindentation, the hardness and the elastic modulus of materials can be determined with high precision. The focus of these analyses is usually on the materials from the metal, ceramic, and plastics processing industry. The application of nanoindentation in construction science, especially in concrete technology, is a relatively new field of investigation. This study deals with the basic application of nanoindentation for the mechanical characterization of hardened cement paste. In particular, the effects of sample preparation and the selection of the nanoindentation measurement parameters on the obtained results are the main subjects of this investigation. The results re intended to show the opportunities and limitations of analyzing a heterogeneous material such as hardened cement paste. The findings are used to assess the suitability of the nanoindentation method for investigating durability-related damage (e.g., due to freeze–thaw or alkali–silica reaction) in concrete.
Open AccessSystematic Experimental Investigation into the Determination of Micromechanical Properties of Hardened Cement Paste Using Nanoindentation—Opportunities and Limitations
The nanoindentation technique is already widely applied in the mechanical characterization of the microstructure of thin films with respect to different materials. Generally, by means of nanoindentation, the hardness and the elastic modulus of materials can be determined with high precision. The focus of these analyses is usually on the materials from the metal, ceramic, and plastics processing industry. The application of nanoindentation in construction science, especially in concrete technology, is a relatively new field of investigation. This study deals with the basic application of nanoindentation for the mechanical characterization of hardened cement paste. In particular, the effects of sample preparation and the selection of the nanoindentation measurement parameters on the obtained results are the main subjects of this investigation. The results re intended to show the opportunities and limitations of analyzing a heterogeneous material such as hardened cement paste. The findings are used to assess the suitability of the nanoindentation method for investigating durability-related damage (e.g., due to freeze–thaw or alkali–silica reaction) in concrete.
- Open Access
Thermodynamic Modeling and Experimental Validation of Acetic Acid Attack on Hardened Cement Paste: Effect of Silica Fume
Concrete structures are increasingly becoming exposed to organic acid attack conditions, such as those found in agriculture and food-related industries. This paper aims to experimentally verify the thermodynamic modeling of cement pastes under acetic acid attack. For this, a modeling approach implemented in IPHREEQC via Matlab is described, and results are compared with measured pH and compositions of equilibrated solutions (MP-AES) as well as unreacted/precipitated solids (XRF, XRD and STA) for a wide range of acid concentrations. The 11% replacement of cement by silica fume (SF) led to a 60 or 70% reduction (measured or modeled, respectively) of Portlandite content in the hardened cement paste due to the pozzolanic reaction resulting in higher content of CSH phases, which has effects on the progression of dissolution processes and a resulting pH with increased acid concentrations. Considering that no fitting parameter was used, the model predictions showed good agreement with measured values of pH, dissolved ion concentrations and composition of the remaining (degraded) solids overall. The discrepancies here were more pronounced at very high acid concentrations (equilibrium pH < ~4), i.e., after the full dissolution of hydrate phases due to limitations in the model used to describe Al-, Si- and Fe-gel phases and/or identified experimental challenges in precipitation of calcium and aluminum acetate hydrates.
Open AccessThermodynamic Modeling and Experimental Validation of Acetic Acid Attack on Hardened Cement Paste: Effect of Silica Fume
Concrete structures are increasingly becoming exposed to organic acid attack conditions, such as those found in agriculture and food-related industries. This paper aims to experimentally verify the thermodynamic modeling of cement pastes under acetic acid attack. For this, a modeling approach implemented in IPHREEQC via Matlab is described, and results are compared with measured pH and compositions of equilibrated solutions (MP-AES) as well as unreacted/precipitated solids (XRF, XRD and STA) for a wide range of acid concentrations. The 11% replacement of cement by silica fume (SF) led to a 60 or 70% reduction (measured or modeled, respectively) of Portlandite content in the hardened cement paste due to the pozzolanic reaction resulting in higher content of CSH phases, which has effects on the progression of dissolution processes and a resulting pH with increased acid concentrations. Considering that no fitting parameter was used, the model predictions showed good agreement with measured values of pH, dissolved ion concentrations and composition of the remaining (degraded) solids overall. The discrepancies here were more pronounced at very high acid concentrations (equilibrium pH < ~4), i.e., after the full dissolution of hydrate phases due to limitations in the model used to describe Al-, Si- and Fe-gel phases and/or identified experimental challenges in precipitation of calcium and aluminum acetate hydrates.
- Open Access
- 21 March 2020
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 18 (3) , 83-94
Influence of Drying on the Microstructure of Hardened Cement Paste: A Mercury Intrusion Porosimetry, Nitrogen Sorption and SAXS Study
Since the durability of concrete depends on the paste matrix, a sound knowledge of its pore structure is required. The most common methods to investigate the microstructure like mercury intrusion porosimetry (MIP) and gas sorption require the removal of free water in the pore space. However, the different drying methods used for this task either do not remove all free water or remove also chemically bound water and thus alter the microstructure. Small-angle X-ray scattering (SAXS) is one of the rare methods which allows to investigate the microstructure without complete water removal. Therefore, in order to compare the effect of different drying methods on the pore structure, hardened OPC paste samples (w/c = 0.5) were investigated with MIP, nitrogen sorption and for the first time with SAXS, after different drying was carried out. Since specific surfaces obtained for SAXS showed a similar trend as for MIP and nitrogen sorption, it can be concluded that SAXS can be utilized to predict the influence of drying on these methods as well. Solvent exchange appears to be a drying method that preserves the microstructure well, since for this the largest specific surface was obtained.
- 21 March 2020
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 18 (3) , 83-94
Open AccessInfluence of Drying on the Microstructure of Hardened Cement Paste: A Mercury Intrusion Porosimetry, Nitrogen Sorption and SAXS Study
Since the durability of concrete depends on the paste matrix, a sound knowledge of its pore structure is required. The most common methods to investigate the microstructure like mercury intrusion porosimetry (MIP) and gas sorption require the removal of free water in the pore space. However, the different drying methods used for this task either do not remove all free water or remove also chemically bound water and thus alter the microstructure. Small-angle X-ray scattering (SAXS) is one of the rare methods which allows to investigate the microstructure without complete water removal. Therefore, in order to compare the effect of different drying methods on the pore structure, hardened OPC paste samples (w/c = 0.5) were investigated with MIP, nitrogen sorption and for the first time with SAXS, after different drying was carried out. Since specific surfaces obtained for SAXS showed a similar trend as for MIP and nitrogen sorption, it can be concluded that SAXS can be utilized to predict the influence of drying on these methods as well. Solvent exchange appears to be a drying method that preserves the microstructure well, since for this the largest specific surface was obtained.