Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Armanto Pardamean Simanjuntak has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Thermo-hydraulic performance of interconnected mini-channels with periodic boundary layer interruption

    by Armanto Pardamean Simanjuntak, Joohan Bae, Jae-Young Lee

    Printed circuit heat exchangers require channel geometries that provide effective heat transfer without excessive hydraulic resistance. This study numerically investigates the effect of the interconnection ratio, Sy/Py , on the thermal-hydraulic performance of a staggered mini-channel with periodic interconnection zones. Three configurations, Sy/Py = 0.25, 0.5, and 0.75, were evaluated over Re = 2700–7900 using three-dimensional RANS simulations with the RNG k-ε model and Enhanced Wall Treatment. Increasing the interconnection ratio strengthened transverse flow between adjacent channels, with the transverse velocity reaching approximately 0.4 m/s at Sy/Py = 0.75. However, stronger transverse flow was accompanied by increased hydraulic resistance. Increasing Sy/Py from 0.25 to 0.5 increased the friction factor by approximately 42%. The configuration provided the highest heat-transfer performance, with a Nusselt number approximately 16% higher than that of Sy/Py = 0.25. A further increase to Sy/Py = 0.75 did not improve heat transfer because larger low-velocity recirculation regions reduced effective convection near the heated surface. Thermal enhancement factor analysis showed that Sy/Py = 0.25 provided the highest overall thermo-hydraulic performance because of its lower hydraulic resistance. These results demonstrate that the interconnection ratio controls the balance between transverse flow exchange, heat-transfer enhancement, and pressure loss.

  • Open Access

    Optimal Design Guidelines for Efficient Energy Harvesting in Piezoelectric Bladeless Wind Turbines

    by Joohan Bae, Armanto Pardamean Simanjuntak, Jae Young Lee

    This study presents an optimal design methodology for a piezoelectric-based bladeless wind turbine (BWT) that efficiently converts wind-induced vibration of a cantilever-mounted cylinder into electrical energy. A lumped-parameter model integrating structural dynamics, fluid-structure interaction, and piezoelectric energy conversion is introduced and simplified to derive key dimensionless design parameters and optimal conditions for maximizing power output. The optimal design criteria are as follows: tuning the resonance between the structural natural frequency and vortex shedding frequency; setting the dimensionless load resistance R* to unity; and minimizing ωnRLCeq to a value smaller than unity. Numerical simulations and wind tunnel experiments validate the model, showing good agreement with less than 7% error in power prediction under resonance conditions and successfully predicting the coupled behavior of fluid, structure, and piezoelectric components. The proposed optimal design methodology facilitates the development of compact and efficient piezoelectric-based bladeless wind energy harvesting systems suitable for urban and space-constrained environments.


  • Open Access

    A Study on Thermal Performance Enhancement of Mini-Channel Cooling Plates with an Interconnected Design for Li-Ion Battery Cooling

    by Armanto P. Simanjuntak, Joohan Bae, Benrico Fredi Simamora, Jae Young Lee

    The increasing adoption of lithium-ion (Li-ion) batteries in electric vehicles (EVs) and renewable energy systems has heightened the demand for efficient Battery Thermal Management Systems (BTMS). Effective thermal regulation is critical to prevent performance degradation, extend battery lifespan, and mitigate safety risks such as thermal runaway. Liquid cooling has become the dominant strategy in commercial EVs due to its superior thermal performance over air cooling. However, optimizing liquid cooling systems remains challenging due to the trade-off between heat transfer efficiency and pressure drop. Recent studies have explored various coolant selection, nanofluid enhancements, and complex channel geometries, an ideal balance remains difficult to achieve. While advanced methods such as topology optimization offer promising performance gains, they often introduce significant modeling and manufacturing complexity. In this study, we propose a practical alternative: an interconnected straight-channel cooling plate that introduces lateral passages to disrupt the thermal boundary layer and enhance mixing. Comparative analysis shows that the design improves temperature uniformity and reduces peak battery temperature, all while maintaining a moderate pressure drop. The proposed configuration offers a scalable and effective solution for next-generation BTMS, particularly in EV applications where thermal performance and manufacturability are both critical.


  • Open Access

    Mechanical Integrity Assessment of Two-Side Etched Type Printed Circuit Heat Exchanger with Additional Elliptical Channel

    by Armanto P. Simanjuntak, Jae-Young Lee

    Printed circuit heat exchangers (PCHEs) are often subject to high pressure and temperature difference between the hot and cold channels which may cause a mechanical integrity problem. A conventional plate heat exchanger where the channel geometries are semi-circular and etched at one side of the stacked plate is a common design in the market. However, the sharp edge tip channel may cause high stress intensity. Double-faced type PCHE appears with the promising ability to reduce the stress intensity and stress concentration factor. Finite element analysis simulation has been conducted to observe the mechanical integrity of double-etched printed circuit heat exchanger design. The application of an additional ellipse upper channel helps the stress intensity decrease in the proposed PCHE channel. Five different cases were simulated in this study. The simulation shows that the stress intensity was reduced up to 24% with the increase in additional elliptical channel radius. Besides that, the horizontal offset channels configuration was also investigated in this study. Simulation results show that the maximum stress intensity of 2.5 mm offset configuration is 9% lower compared to the maximum stress intensity of 0 mm offset. This work proposed an additional elliptical upper channel with a 2.5 mm offset configuration as an optimum design.


  • Open Access

    Mechanical Integrity Analysis of a Printed Circuit Heat Exchanger with Channel Misalignment

    by Armanto P. Simanjuntak, Jae Young Lee

    Printed circuit heat exchangers (PCHEs), which are used for thermal heat storage and power generation, are often subject to severe pressure and temperature differences between primary and secondary channels, which causes mechanical integrity problems. PCHE operation may result in discontinuity, such as channel misalignment, due to non-uniform thermal fields in the diffusion bonding process. The present paper analyzes the mechanical integrity, including the utilization factors of stress and deformation under various channel misalignment conditions. The pressure difference of the target PCHE is 19.5 MPa due to the high pressure (19.7 MPa) of the steam channel in the Rankine cycle and the low pressure (0.5 MPa) of molten salt or liquid metal in the primary channel. Additionally, the temperature difference between channels is around 25 °C, however the average temperature is around 500 °C. The PCHE has a relatively large primary channel measuring approximately 3 x 3 mm, and a steam channel measuring 2 x 1.5 mm. The finite element method (FEM) is applied to determine the stress by changing the misalignment to below 30% of the primary channel width. It was found that the current PCHE is operable up to 700 °C in terms of the ASME code under these design conditions. Additionally, the change of utilization factor due to the misalignment increases, but is still under the ASME acceptance criteria of 700 °C; however, it violates the criteria at 725 °C, which is the allowable temperature condition. Therefore, the mechanical integrity of the PCHE with low-pressure molten salt or liquid metal and a high-pressure steam channel is acceptable in terms of utilization factor.