Abdulmumin Ahmed Shuaibu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abdulmumin Ahmed Shuaibu has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Zhiping Zeng
School of Civil Engineering, Central South University, Changsha 410083, China
5 shared publications - Weidong Wang
School of Civil Engineering, Central South University, Changsha 410075, China
3 shared publications - Yu Yuan
Information Engineering School, Nanchang University, Nanchang 330031, China
3 shared publications - Guangzhao Peng
School of Civil Engineering, Central South University, Changsha 410075, China
2 shared publications - Ji Hu
School of Civil Engineering, Central South University, Changsha 410075, China
2 shared publications - Weidong Wang
School of Civil Engineering, Central South University, Changsha 410075, China
2 shared publications
Latest Publications
- Open Access
Experimental Research on Vibration-Damping Effect of Combined Shear Hinge Prefabricated Steel Spring Floating Slab Track
Objective: The cast-in-place steel spring floating slab track (SSFST) is difficult to maintain and repair, while the mechanical strength of the end of the traditional prefabricated SSFST is poor. In order to overcome the above shortcomings, a shear-hinge-combined prefabricated SSFST was developed, and an indoor test was carried out to analyze its vibration-damping effect. Methods: A combined shear hinge SSFST connection model with two length sizes was established. The dynamic response amplitude and frequency response characteristics of the foundation (ground) under different isolator installations and fatigue loads were studied, and the vibration-damping performance of two sizes of combined shear hinge SSFST was evaluated. Results: The vibration-damping effect of the steel spring vibration isolator mainly acts in the middle and low-frequency bands of 16–400 Hz, and the vibration near 10 Hz will be aggravated after the vibration isolator is installed. The vibration index and variation law of the two sizes of SSFST are similar, and the vibration response of 4.8 m SSFST is slightly less than 3.6 m SSFST. There is almost no change in each index when the load is 5 million times, and there is a certain range of change when the load is 10 million times, but the overall change is small. Conclusions: The combined shear hinge prefabricated SSFST can have an excellent isolation effect on vibration and can still maintain good vibration-damping ability within 10 million fatigue loads (about 5 years); 4.8 m SSFST should be laid in straight sections with higher train speeds, while 3.6 m SSFST should be applied in curved sections to ensure smooth lines.
Open AccessExperimental Research on Vibration-Damping Effect of Combined Shear Hinge Prefabricated Steel Spring Floating Slab Track
Objective: The cast-in-place steel spring floating slab track (SSFST) is difficult to maintain and repair, while the mechanical strength of the end of the traditional prefabricated SSFST is poor. In order to overcome the above shortcomings, a shear-hinge-combined prefabricated SSFST was developed, and an indoor test was carried out to analyze its vibration-damping effect. Methods: A combined shear hinge SSFST connection model with two length sizes was established. The dynamic response amplitude and frequency response characteristics of the foundation (ground) under different isolator installations and fatigue loads were studied, and the vibration-damping performance of two sizes of combined shear hinge SSFST was evaluated. Results: The vibration-damping effect of the steel spring vibration isolator mainly acts in the middle and low-frequency bands of 16–400 Hz, and the vibration near 10 Hz will be aggravated after the vibration isolator is installed. The vibration index and variation law of the two sizes of SSFST are similar, and the vibration response of 4.8 m SSFST is slightly less than 3.6 m SSFST. There is almost no change in each index when the load is 5 million times, and there is a certain range of change when the load is 10 million times, but the overall change is small. Conclusions: The combined shear hinge prefabricated SSFST can have an excellent isolation effect on vibration and can still maintain good vibration-damping ability within 10 million fatigue loads (about 5 years); 4.8 m SSFST should be laid in straight sections with higher train speeds, while 3.6 m SSFST should be applied in curved sections to ensure smooth lines.
- Open Access
- 7 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1694
Research on Fatigue Damage Evolution of the Base Plate Structure of China Railway Track System III Type Slab Ballastless Track under Heavy Haul Train Load
To meet the transportation requirements of heavy-haul trains, it is necessary to consider the use of prestressed reinforced concrete ballastless tracks. Therefore, the CRTSIII SBT (China Railway Track System III-type slab ballastless track) has been considered for its convenient construction and geometric adjustment. Considering the problems existing in the base plate of CRTSIII SBT in heavy-haul applications, an indoor test and simulation were conducted to explore the cracking phenomenon of the base plate concrete under fatigue load. The reliability of the simulation was verified through the experimental results. A fatigue crack development law of the base plate structure was established. Furthermore, the influence of the load position, the thickness of self-compacting concrete and axle loads on the fatigue damage of the base plate structure were investigated. For the CRTSIII SBT subjected to heavier axle loads, it is appropriate to thicken the self-compacting concrete layer and strengthen the concrete and steel reinforcement at the plate end to reduce fatigue damage and cracks. The research results can serve as a basis for the optimization of the CRTSIII SBT base plate structure in heavy-haul railway applications.
- 7 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1694
Open AccessResearch on Fatigue Damage Evolution of the Base Plate Structure of China Railway Track System III Type Slab Ballastless Track under Heavy Haul Train Load
To meet the transportation requirements of heavy-haul trains, it is necessary to consider the use of prestressed reinforced concrete ballastless tracks. Therefore, the CRTSIII SBT (China Railway Track System III-type slab ballastless track) has been considered for its convenient construction and geometric adjustment. Considering the problems existing in the base plate of CRTSIII SBT in heavy-haul applications, an indoor test and simulation were conducted to explore the cracking phenomenon of the base plate concrete under fatigue load. The reliability of the simulation was verified through the experimental results. A fatigue crack development law of the base plate structure was established. Furthermore, the influence of the load position, the thickness of self-compacting concrete and axle loads on the fatigue damage of the base plate structure were investigated. For the CRTSIII SBT subjected to heavier axle loads, it is appropriate to thicken the self-compacting concrete layer and strengthen the concrete and steel reinforcement at the plate end to reduce fatigue damage and cracks. The research results can serve as a basis for the optimization of the CRTSIII SBT base plate structure in heavy-haul railway applications.
- Open Access
Research on the Variable-Temperature Cracking Mechanism of CRTS I Type Double-Block Ballastless Track on a Bridge
The CRTS I type double-block ballastless track (CRTS I TDBBT) has the advantages of convenient construction and low cost, but it has low crack resistance and the temperature field distribution of the railway on the bridge is uneven and frequently changes, so it is necessary to study the mechanical properties of the CRTS I TDBBT under the load of a temperature field. The temperature field model of the CRTS I TDBBT on the bridge is established by finite element software, the real-time temperature field of the track bed slab is brought into the coupled model as a load, and the variation laws of the temperature stress of the CRTS I TDBBT under different schemes are compared. The temperature gradient in the CRTS I TDBBT track bed slab has the largest fluctuation range, and the positive and negative temperature gradient range can reach 93.34 °C. For the temperature longitudinal stress around the sleeper block of the track bed slab, the edge is the largest; the temperature longitudinal stress is reduced by at most 5.27% after the anti-cracking diagonal bars are added. When the expansion joint is added, the temperature stress can be reduced by up to 80.29%. The fluctuation range of the temperature gradient of the track bed is basically consistent with the fluctuation range of the local air temperature. The huge temperature difference leads to the occurrence of cracks in the track structure, and cracks are more likely to occur at the corners of the sleeper block. The addition of both anti-crack diagonal bars and expansion joints has an anti-crack effect, but the effect of adding expansion joints is better.
Open AccessResearch on the Variable-Temperature Cracking Mechanism of CRTS I Type Double-Block Ballastless Track on a Bridge
The CRTS I type double-block ballastless track (CRTS I TDBBT) has the advantages of convenient construction and low cost, but it has low crack resistance and the temperature field distribution of the railway on the bridge is uneven and frequently changes, so it is necessary to study the mechanical properties of the CRTS I TDBBT under the load of a temperature field. The temperature field model of the CRTS I TDBBT on the bridge is established by finite element software, the real-time temperature field of the track bed slab is brought into the coupled model as a load, and the variation laws of the temperature stress of the CRTS I TDBBT under different schemes are compared. The temperature gradient in the CRTS I TDBBT track bed slab has the largest fluctuation range, and the positive and negative temperature gradient range can reach 93.34 °C. For the temperature longitudinal stress around the sleeper block of the track bed slab, the edge is the largest; the temperature longitudinal stress is reduced by at most 5.27% after the anti-cracking diagonal bars are added. When the expansion joint is added, the temperature stress can be reduced by up to 80.29%. The fluctuation range of the temperature gradient of the track bed is basically consistent with the fluctuation range of the local air temperature. The huge temperature difference leads to the occurrence of cracks in the track structure, and cracks are more likely to occur at the corners of the sleeper block. The addition of both anti-crack diagonal bars and expansion joints has an anti-crack effect, but the effect of adding expansion joints is better.
- Open Access
- 1 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (21) , 10232
Research on Mechanical Performance of Improved Low Vibration Track and Its Feasibility Analysis for Heavy-Haul Railway Applications
With the gradual increase of the cargo weight of heavy-haul trains, the traditional ballasted track with the accumulation of stone and ballast has been unable to meet its structural safety requirements. From the comparison of the three common ballastless tracks in China, it can be seen that the low-vibration track (LVT) has the advantages of reasonable structure, low cost, and easy maintenance. Therefore, the design and research of heavy-haul railways are focused on, and it is urgent to study the applicability of LVT in heavy-haul railways. Method: By improving the slope of the short side of the LVT support block, the support block has a better load bearing capacity, so as to achieve the purpose of bearing a larger axle load. Through 1:1 full-scale model test and finite element simulation, the static mechanical properties of Improved LVT (ILVT) and Traditional LVT (TLVT) are compared and analyzed. Result: Compared with TLVT, ILVT has smaller vertical displacement and track gauge changes when subjected to the same load. The proven and reliable finite element model also shows that ILVT’s load sharing is less affected. In the case of achieving the same deformation, ILVT can withstand greater vertical and lateral loads. Conclusions: Compared with the TLVT, the ILVT design can reduce the vertical displacement of the rail and the supporting block, better control the track subsidence, and improve the driving safety of the LVT. At the same time, ILVT improves the anti-overturning ability of the rail and support block under lateral load, reduces the expansion of the gauge and the lateral spacing of the support block, and improves the stability of the track structure. ILVT can also be considered for the weight of 40t and other large axle load, and has broad application prospects.
- 1 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (21) , 10232
Open AccessResearch on Mechanical Performance of Improved Low Vibration Track and Its Feasibility Analysis for Heavy-Haul Railway Applications
With the gradual increase of the cargo weight of heavy-haul trains, the traditional ballasted track with the accumulation of stone and ballast has been unable to meet its structural safety requirements. From the comparison of the three common ballastless tracks in China, it can be seen that the low-vibration track (LVT) has the advantages of reasonable structure, low cost, and easy maintenance. Therefore, the design and research of heavy-haul railways are focused on, and it is urgent to study the applicability of LVT in heavy-haul railways. Method: By improving the slope of the short side of the LVT support block, the support block has a better load bearing capacity, so as to achieve the purpose of bearing a larger axle load. Through 1:1 full-scale model test and finite element simulation, the static mechanical properties of Improved LVT (ILVT) and Traditional LVT (TLVT) are compared and analyzed. Result: Compared with TLVT, ILVT has smaller vertical displacement and track gauge changes when subjected to the same load. The proven and reliable finite element model also shows that ILVT’s load sharing is less affected. In the case of achieving the same deformation, ILVT can withstand greater vertical and lateral loads. Conclusions: Compared with the TLVT, the ILVT design can reduce the vertical displacement of the rail and the supporting block, better control the track subsidence, and improve the driving safety of the LVT. At the same time, ILVT improves the anti-overturning ability of the rail and support block under lateral load, reduces the expansion of the gauge and the lateral spacing of the support block, and improves the stability of the track structure. ILVT can also be considered for the weight of 40t and other large axle load, and has broad application prospects.
- Open Access
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Experimental Study on the Sliding of WJ‐8 Small Resistance Fastener Composite Pad
Under long‐term temperature loading, long bridges stretch and deform, causing the beam and rail to move relative to each other. This phenomenon could cause a gradual slide of the rail relative to the fastener composite pad and ultimately results in the slipping out of the fastener pad at the end of the ballastless track bridge changes. The slipping out of the fastener composite pad changes the longitudinal resistance of the fastener and causes shock of the train on the rail structure due to direct contact between the rail and the tie, thus inhibiting the normal use of the line. In this paper, a reciprocating tensile test was carried out on a WJ‐8 small resistance fastener to explore the breaking process of the fastener composite pad, identify the interaction mechanism of the fastener composite pad under the rail, and ultimately determine the influence of the pad on the longitudinal resistance of the fastener. The results show that the two factors that affect the longitudinal resistance of the fastener under reciprocating loading are the surface roughness and displacement of the fastener composite pad. While the surface roughness of the fastener composite pad is the main influencing factor in the early stage, the displacement of the composite pad has a greater impact on the later stage. The research results of this paper can provide an important reference for the maintenance and repair of ballastless track fasteners on bridges.
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Open AccessExperimental Study on the Sliding of WJ‐8 Small Resistance Fastener Composite Pad
Under long‐term temperature loading, long bridges stretch and deform, causing the beam and rail to move relative to each other. This phenomenon could cause a gradual slide of the rail relative to the fastener composite pad and ultimately results in the slipping out of the fastener pad at the end of the ballastless track bridge changes. The slipping out of the fastener composite pad changes the longitudinal resistance of the fastener and causes shock of the train on the rail structure due to direct contact between the rail and the tie, thus inhibiting the normal use of the line. In this paper, a reciprocating tensile test was carried out on a WJ‐8 small resistance fastener to explore the breaking process of the fastener composite pad, identify the interaction mechanism of the fastener composite pad under the rail, and ultimately determine the influence of the pad on the longitudinal resistance of the fastener. The results show that the two factors that affect the longitudinal resistance of the fastener under reciprocating loading are the surface roughness and displacement of the fastener composite pad. While the surface roughness of the fastener composite pad is the main influencing factor in the early stage, the displacement of the composite pad has a greater impact on the later stage. The research results of this paper can provide an important reference for the maintenance and repair of ballastless track fasteners on bridges.
- Open Access
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Performance Analysis of Prefabricated Steel‐Spring Floating‐Slab Track and Its Application to Urban Express Rail Transit
The aim of the research is the design of prefabricated steel‐spring floating‐slab track to be applied in urban express rail transit systems. Using a developed vehicle‐track dynamic‐coupling equation for steel‐spring floating‐slab track, the effects of length, thickness, vertical damping, and use of side‐mounted isolators on the floating‐slab track were investigated experimentally using full‐scale model and under different working conditions. The finding of the study revealed the following: (1) The prefabricated steel‐spring floating‐slab track can be applied to urban express rail transit, because it meets the requirements of high‐speed transit while efficiently reducing noise. (2) The floating‐slab track’s stability slightly increases with the increase of its length and thickness. As thickness increases, vertical displacement of the rail increases slightly, and lateral stability increases, thereby slightly improving the vehicle’s running stability. (3) When the intercity electric multiple‐unit train travels along the prefabricated steel‐spring floating‐slab‐track bed at different speeds, the wheel‐axle lateral force, wheel‐rail vertical force, the derailment coefficient, the wheel‐weight reduction rate, and the lateral acceleration of the vehicle body are all less than the specified limits of Chinese code, thus fully meeting the safety requirements of train operation. (4) Appropriately increasing the vertical‐support damping of the floating slab can improve the vehicle’s vertical dynamic performance, reduce the vertical displacement of the rail, and lower the vibration response of the floating slab. (5) Adding side‐mounted vibration isolators at the joint of the floating slab could greatly improve the stability of the floating slab itself and appropriately reduce the vehicle’s vertical vibration response. Due to the optimization and establishment of relevant factors influencing the performance of prefabricated steel‐string floating‐slab track achieved in the study, the results obtained are particularly useful for setting safety, comfort, and stability requirements of the floating slab.
- 1 January 2020
- Published by Wiley in Advances in Civil Engineering
- Vol. 2020 (1)
Open AccessPerformance Analysis of Prefabricated Steel‐Spring Floating‐Slab Track and Its Application to Urban Express Rail Transit
The aim of the research is the design of prefabricated steel‐spring floating‐slab track to be applied in urban express rail transit systems. Using a developed vehicle‐track dynamic‐coupling equation for steel‐spring floating‐slab track, the effects of length, thickness, vertical damping, and use of side‐mounted isolators on the floating‐slab track were investigated experimentally using full‐scale model and under different working conditions. The finding of the study revealed the following: (1) The prefabricated steel‐spring floating‐slab track can be applied to urban express rail transit, because it meets the requirements of high‐speed transit while efficiently reducing noise. (2) The floating‐slab track’s stability slightly increases with the increase of its length and thickness. As thickness increases, vertical displacement of the rail increases slightly, and lateral stability increases, thereby slightly improving the vehicle’s running stability. (3) When the intercity electric multiple‐unit train travels along the prefabricated steel‐spring floating‐slab‐track bed at different speeds, the wheel‐axle lateral force, wheel‐rail vertical force, the derailment coefficient, the wheel‐weight reduction rate, and the lateral acceleration of the vehicle body are all less than the specified limits of Chinese code, thus fully meeting the safety requirements of train operation. (4) Appropriately increasing the vertical‐support damping of the floating slab can improve the vehicle’s vertical dynamic performance, reduce the vertical displacement of the rail, and lower the vibration response of the floating slab. (5) Adding side‐mounted vibration isolators at the joint of the floating slab could greatly improve the stability of the floating slab itself and appropriately reduce the vehicle’s vertical vibration response. Due to the optimization and establishment of relevant factors influencing the performance of prefabricated steel‐string floating‐slab track achieved in the study, the results obtained are particularly useful for setting safety, comfort, and stability requirements of the floating slab.