James G. Soules
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
James G. Soules has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- H. Scott Norville
Professor, Dept. of Civil, Environmental, and Construction Engineering, Texas Tech Univ., Lubbock, TX 79409. ORCID:
4 shared publications Stephen M. Morse
Assistant Professor, Dept. of Civil and Environmental Engineering, Michigan Technological Univ., Houghton, MI 49931
2 shared publications- Stephen Michael Morse
Assistant Professor, Dept. of Civil and Environmental Engineering, Michigan Technological Univ., Houghton, MI 49931. ORCID:
2 shared publications
Latest Publications
- 1 March 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 29 (1) , 04023002
Effects of Fixed Edge Conditions on the Load Resistance of Single Glass Lites
The load resistance (LR) of glass lites is determined in the United States by use of standards based on a probabilistic model of glass breakage. These standards generally restrict design to rectangular glass lites continuously supported along one, two, three, or four sides. In addition, these standards treat single glass lites as simply supported flat rectangular plates. Historically, rigid window frames supported single glass lites holding them in place with neoprene or similar gasket material. This attachment method approximated simply supported edges that rotate about an axis parallel to the simply supported edges, deform in the plane of the glass lite, and do not deflect out-of-plane. Advances in structural silicone make it possible to produce rectangular single flat glass lites with edge fixity somewhere between that of simply supported edges and fully fixed edges. The authors applied the glass failure prediction model (GFPM) to a nonlinear finite-element model developed previously by the authors to determine the probability of breakage for selected single glass lite geometries with fully fixed edges under uniform lateral loads. The paper presents comparisons between results of analyses of lites with fixed edges with analyses of lites with simply supported edges. The comparisons indicate that not all single glass lite geometries benefit from fully fixing edges, but the benefits of doing so appear to increase as lite aspect ratio (AR) increases. The comparisons bracket benefits that can accrue from the partial fixity provided by structural silicone supports. The actual degree of fixity provided by structural silicone can only be determined experimentally, which lies outside the scope of this paper.
- 1 March 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 29 (1) , 04023002
Effects of Fixed Edge Conditions on the Load Resistance of Single Glass Lites
The load resistance (LR) of glass lites is determined in the United States by use of standards based on a probabilistic model of glass breakage. These standards generally restrict design to rectangular glass lites continuously supported along one, two, three, or four sides. In addition, these standards treat single glass lites as simply supported flat rectangular plates. Historically, rigid window frames supported single glass lites holding them in place with neoprene or similar gasket material. This attachment method approximated simply supported edges that rotate about an axis parallel to the simply supported edges, deform in the plane of the glass lite, and do not deflect out-of-plane. Advances in structural silicone make it possible to produce rectangular single flat glass lites with edge fixity somewhere between that of simply supported edges and fully fixed edges. The authors applied the glass failure prediction model (GFPM) to a nonlinear finite-element model developed previously by the authors to determine the probability of breakage for selected single glass lite geometries with fully fixed edges under uniform lateral loads. The paper presents comparisons between results of analyses of lites with fixed edges with analyses of lites with simply supported edges. The comparisons indicate that not all single glass lite geometries benefit from fully fixing edges, but the benefits of doing so appear to increase as lite aspect ratio (AR) increases. The comparisons bracket benefits that can accrue from the partial fixity provided by structural silicone supports. The actual degree of fixity provided by structural silicone can only be determined experimentally, which lies outside the scope of this paper.
- 1 June 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 27 (2) , 04021001
Application of Glass Failure Prediction Model to Bent Glass Using Finite-Element Modeling
Designers of architectural glass in the United States rely on model building codes and standards for definitions of load resistance (LR) and other factors pertinent to design. Unfortunately, US model building codes and standards currently address only flat glass. These US model building codes and standards provide no generally accepted methodology to facilitate the determination of LT for bent glass. Because architects frequently use bent glass in buildings, a well-defined procedure for determining its LR is needed. The primary analysis tools available to engineers today are based on the finite-element method and can be applied to a wide range of different glass lite geometries. The authors developed a nonlinear finite-element model and applied the glass failure prediction model (GFPM) to the nonlinear finite-element model output to determine the probability of breakage for the specified bent glass lite geometry and the selected load combinations. The results of their analyses compare favorably to the stresses obtained from a strain gauged full-scale bent glass lite test specimen. The authors also compared the LR of the bent glass lite to the LR of a flat glass lite with the same rectangular dimensions of the bent glass lite to demonstrate the strength increase of bent glass constructions over flat glass constructions for the single geometry studied.
- 1 June 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 27 (2) , 04021001
Application of Glass Failure Prediction Model to Bent Glass Using Finite-Element Modeling
Designers of architectural glass in the United States rely on model building codes and standards for definitions of load resistance (LR) and other factors pertinent to design. Unfortunately, US model building codes and standards currently address only flat glass. These US model building codes and standards provide no generally accepted methodology to facilitate the determination of LT for bent glass. Because architects frequently use bent glass in buildings, a well-defined procedure for determining its LR is needed. The primary analysis tools available to engineers today are based on the finite-element method and can be applied to a wide range of different glass lite geometries. The authors developed a nonlinear finite-element model and applied the glass failure prediction model (GFPM) to the nonlinear finite-element model output to determine the probability of breakage for the specified bent glass lite geometry and the selected load combinations. The results of their analyses compare favorably to the stresses obtained from a strain gauged full-scale bent glass lite test specimen. The authors also compared the LR of the bent glass lite to the LR of a flat glass lite with the same rectangular dimensions of the bent glass lite to demonstrate the strength increase of bent glass constructions over flat glass constructions for the single geometry studied.
- 1 December 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 26 (4) , 04020037
Application of the Glass Failure Prediction Model to Flat Odd-Shaped Glass Using Finite-Element Modeling
Model building codes and standards in the United States find their bases in a probabilistic model of glass load resistance (LR). In general, architectural flat glass design predicated on these model building codes and standards is restricted to rectangular glass lites continuously supported along one, two, three, or four sides. When a design professional wishes to use glass with an odd shape (i.e., a nonrectangular shape), design procedures in the model building codes and standards regress to a maximum stress approach. A maximum stress approach to design represents a much different philosophy than does the probabilistic approach. When compared to the probabilistic approach, designs based upon a value of maximum allowable stress may result in much less efficient design. Therefore, the need exists for a design approach for odd-shaped glass lites that has a probabilistic basis for glass load resistance. The primary analysis tools available to engineers today are based on the finite-element method and can be applied to a wide range of different glass lite geometries. The authors developed a nonlinear finite-element model and applied the glass failure prediction model (GFPM) to the nonlinear finite-element model output to determine probability of breakage for combinations of selected flat odd-shaped glass lite geometries and loads. The authors compared the LR of the odd-shaped glass lites to the LR of flat glass lites with the LR of rectangular glass lites having the smallest dimensions so that they would encompass the odd-shaped lites. The authors also compared the maximum principal stresses determined for the flat odd-shaped glass lites (loaded with a pressure equal to the LR of the flat odd-shaped glass lites) from the nonlinear finite-element model to recommended values of maximum allowable stress from model building codes and standards.
- 1 December 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 26 (4) , 04020037
Application of the Glass Failure Prediction Model to Flat Odd-Shaped Glass Using Finite-Element Modeling
Model building codes and standards in the United States find their bases in a probabilistic model of glass load resistance (LR). In general, architectural flat glass design predicated on these model building codes and standards is restricted to rectangular glass lites continuously supported along one, two, three, or four sides. When a design professional wishes to use glass with an odd shape (i.e., a nonrectangular shape), design procedures in the model building codes and standards regress to a maximum stress approach. A maximum stress approach to design represents a much different philosophy than does the probabilistic approach. When compared to the probabilistic approach, designs based upon a value of maximum allowable stress may result in much less efficient design. Therefore, the need exists for a design approach for odd-shaped glass lites that has a probabilistic basis for glass load resistance. The primary analysis tools available to engineers today are based on the finite-element method and can be applied to a wide range of different glass lite geometries. The authors developed a nonlinear finite-element model and applied the glass failure prediction model (GFPM) to the nonlinear finite-element model output to determine probability of breakage for combinations of selected flat odd-shaped glass lite geometries and loads. The authors compared the LR of the odd-shaped glass lites to the LR of flat glass lites with the LR of rectangular glass lites having the smallest dimensions so that they would encompass the odd-shaped lites. The authors also compared the maximum principal stresses determined for the flat odd-shaped glass lites (loaded with a pressure equal to the LR of the flat odd-shaped glass lites) from the nonlinear finite-element model to recommended values of maximum allowable stress from model building codes and standards.
- 1 June 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 26 (2)
Application of the Glass Failure Prediction Model to Flat Glass Using Finite-Element Modeling
Architectural glazing designers in the United States and many other parts of the world use prescriptive methods to determine the load resistance (LR) of glazing and glazing constructions in buildings based on a probabilistic theory of glass strength. This theory is known as the glass failure prediction model (GFPM). The GFPM relates the probability of breakage to surface stress magnitude induced by lateral uniform loads acting on the glass as well as the duration of stress. Glass design charts in US model building codes and standards use a nonlinear finite difference model developed during the early 1980s as the basis to determine surface stresses induced by lateral loads. The primary analysis tools available to engineers today are based on the finite-element method and not on the finite difference method. The authors developed a nonlinear finite-element model and applied the GFPM to the nonlinear finite-element model output to determine the probability of breakage for selected glass lite geometry and load combinations. The results of their analyses compare favorably with values in model building codes and standards. This model will facilitate architectural glazing designers when they must design glazing for fenestrations that charts in model building codes and standards currently do not address.
- 1 June 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 26 (2)
Application of the Glass Failure Prediction Model to Flat Glass Using Finite-Element Modeling
Architectural glazing designers in the United States and many other parts of the world use prescriptive methods to determine the load resistance (LR) of glazing and glazing constructions in buildings based on a probabilistic theory of glass strength. This theory is known as the glass failure prediction model (GFPM). The GFPM relates the probability of breakage to surface stress magnitude induced by lateral uniform loads acting on the glass as well as the duration of stress. Glass design charts in US model building codes and standards use a nonlinear finite difference model developed during the early 1980s as the basis to determine surface stresses induced by lateral loads. The primary analysis tools available to engineers today are based on the finite-element method and not on the finite difference method. The authors developed a nonlinear finite-element model and applied the GFPM to the nonlinear finite-element model output to determine the probability of breakage for selected glass lite geometry and load combinations. The results of their analyses compare favorably with values in model building codes and standards. This model will facilitate architectural glazing designers when they must design glazing for fenestrations that charts in model building codes and standards currently do not address.