Madasamy Arockiasamy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Madasamy Arockiasamy has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Rahul Dev Raju
Department of Ocean and Mechanical Engineering, Florida Atlantic University, Boca Raton, FL 33431, USA
4 shared publications - Amir Mirmiran
Provost and Lindsey Chair Professor, Univ. of Texas at Tyler, 3900 University Blvd., Tyler, TX 75799
3 shared publications - William Potter
Project Manager, Structures Research Center, Florida Dept. of Transportation, 2007 E. Paul Dirac Dr., Tallahassee, FL 32310
3 shared publications - Xiong Yang
Ph.D. Candidate, Dept. of Civil and Environmental Engineering, Florida International Univ., Miami, FL 33174
3 shared publications - Pedram Zohrevand
Research Assistant Professor, Dept. of Civil and Environmental Engineering, Florida International Univ., Miami, FL 33174
2 shared publications - Prakash Ankitha Arvan
Department of Civil, Environmental and Geomatics Engineering, Florida Atlantic University, Boca Raton, FL 33431-0991, USA
2 shared publications
Latest Publications
- Open Access
Coupled BEM–FEM Analysis of Coastal Monopile Soil–Structure Interaction Considering Sea-Level Rise and Corrosion-Induced Degradation
Coastal monopile serviceability is influenced by the combined effects of soil–structure interaction, stress-generated excess pore pressure, sea-level rise (SLR), environmental loads, and localized structural degradation. Existing studies commonly address each of these mechanisms individually, while their sequential integration within a common coupled BEM–FEM framework remains comparatively less explored. The present study addresses this gap through a two-dimensional plane-strain coupled BEM–FEM framework in which the structural and elastostatic seabed domains are coupled along the common pile–seabed interface by satisfying displacement compatibility and force equilibrium. The coupled solution is subsequently used for internal seabed-stress recovery, Biot–Skempton stress-generated excess pore-pressure evaluation, equivalent pile–seabed interface-force transfer, one-dimensional Terzaghi-type dissipation, prescribed SLR conditions, quasi-static environmental loads, and localized splash-zone flexural-stiffness degradation. The principal contribution of the present study includes integration of the above established components into a numerically efficient coupled BEM–FEM computational procedure for soil–structure interaction. The benchmark studies demonstrate consistent deformation and stress trends with reduced soil-domain discretization. Within the investigated scenarios, intensified environmental loads produce greater structural responses than prescribed SLR alone, while localized splash-zone degradation primarily increases superstructure flexibility above the mudline.
Open AccessCoupled BEM–FEM Analysis of Coastal Monopile Soil–Structure Interaction Considering Sea-Level Rise and Corrosion-Induced Degradation
Coastal monopile serviceability is influenced by the combined effects of soil–structure interaction, stress-generated excess pore pressure, sea-level rise (SLR), environmental loads, and localized structural degradation. Existing studies commonly address each of these mechanisms individually, while their sequential integration within a common coupled BEM–FEM framework remains comparatively less explored. The present study addresses this gap through a two-dimensional plane-strain coupled BEM–FEM framework in which the structural and elastostatic seabed domains are coupled along the common pile–seabed interface by satisfying displacement compatibility and force equilibrium. The coupled solution is subsequently used for internal seabed-stress recovery, Biot–Skempton stress-generated excess pore-pressure evaluation, equivalent pile–seabed interface-force transfer, one-dimensional Terzaghi-type dissipation, prescribed SLR conditions, quasi-static environmental loads, and localized splash-zone flexural-stiffness degradation. The principal contribution of the present study includes integration of the above established components into a numerically efficient coupled BEM–FEM computational procedure for soil–structure interaction. The benchmark studies demonstrate consistent deformation and stress trends with reduced soil-domain discretization. Within the investigated scenarios, intensified environmental loads produce greater structural responses than prescribed SLR alone, while localized splash-zone degradation primarily increases superstructure flexibility above the mudline.
- Open Access
Coupled BEM-FEM Fracture Response Analysis of Concrete Gravity Seawall Under Sea-Level Rise and Crack-Face Hydrostatic Pressure
Aging concrete seawalls are increasingly exposed to deterioration and sea-level-rise (SLR)-related hydraulic demands, yet the fracture response of pre-existing water-accessible cracks under combined coastal loading remains insufficiently understood. A MATLAB R2025a-based coupled BEM-FEM framework is developed to evaluate a plain-concrete gravity seawall using linear-elastic fracture mechanics (LEFM) under plane-strain conditions. Quadratic boundary elements represent the uncracked seawall region, while a locally refined Q8 FEM patch with quarter-point elements represents the toe-crack response. Parametric analyses consider self-weight, 25% and 50% backfill-pressure reductions, seawater levels of 1.52, 1.82, and 3.05 m, crack-face hydrostatic pressure, and normalized crack lengths, a/W = 0.1–0.7. Benchmark and mesh-sensitivity studies demonstrate stable fracture parameters. Results show that a/W primarily governs the nonlinear increase in fracture response, whereas crack-face hydrostatic pressure reduces both the closure tendency and the J-integral-based equivalent stress-intensity magnitude, KJ. Elevated seawater levels and backfill reduction exert secondary influences. The toughness-normalized index remains below unity, and crack-face displacement is normal-component-dominant. Independent ANSYS 2021R1 analyses provide trend-level corroboration of reduced equivalent fracture magnitude and closure-directed displacement. Overall, the coupled BEM-FEM framework identifies crack length and assumed concrete fracture toughness as governing parameters for the screened response and provides an efficient numerical approach for coastal concrete fracture assessment.
Open AccessCoupled BEM-FEM Fracture Response Analysis of Concrete Gravity Seawall Under Sea-Level Rise and Crack-Face Hydrostatic Pressure
Aging concrete seawalls are increasingly exposed to deterioration and sea-level-rise (SLR)-related hydraulic demands, yet the fracture response of pre-existing water-accessible cracks under combined coastal loading remains insufficiently understood. A MATLAB R2025a-based coupled BEM-FEM framework is developed to evaluate a plain-concrete gravity seawall using linear-elastic fracture mechanics (LEFM) under plane-strain conditions. Quadratic boundary elements represent the uncracked seawall region, while a locally refined Q8 FEM patch with quarter-point elements represents the toe-crack response. Parametric analyses consider self-weight, 25% and 50% backfill-pressure reductions, seawater levels of 1.52, 1.82, and 3.05 m, crack-face hydrostatic pressure, and normalized crack lengths, a/W = 0.1–0.7. Benchmark and mesh-sensitivity studies demonstrate stable fracture parameters. Results show that a/W primarily governs the nonlinear increase in fracture response, whereas crack-face hydrostatic pressure reduces both the closure tendency and the J-integral-based equivalent stress-intensity magnitude, KJ. Elevated seawater levels and backfill reduction exert secondary influences. The toughness-normalized index remains below unity, and crack-face displacement is normal-component-dominant. Independent ANSYS 2021R1 analyses provide trend-level corroboration of reduced equivalent fracture magnitude and closure-directed displacement. Overall, the coupled BEM-FEM framework identifies crack length and assumed concrete fracture toughness as governing parameters for the screened response and provides an efficient numerical approach for coastal concrete fracture assessment.
- Open Access
Feasibility of Using Green Laser for Underwater Infrastructure Monitoring: Case Studies in South Florida
Scour around bridges present a severe threat to the stability of railroad and highway bridges. Scour needs to be monitored to prevent the bridges from becoming damaged. This research studies the feasibility of using green laser for monitoring the scour around candidate railroad and highway bridges. The laboratory experiments that provided the basis for using green laser for underwater mapping are also discussed. The results of the laboratory and field experiments demonstrate the feasibility of using green laser for underwater infrastructure monitoring with limitations on the turbidity of water that affects the penetrability of the laser. This method can be used for scour monitoring around offshore structures in shallow water as well as corrosion monitoring of bridges.
Open AccessFeasibility of Using Green Laser for Underwater Infrastructure Monitoring: Case Studies in South Florida
Scour around bridges present a severe threat to the stability of railroad and highway bridges. Scour needs to be monitored to prevent the bridges from becoming damaged. This research studies the feasibility of using green laser for monitoring the scour around candidate railroad and highway bridges. The laboratory experiments that provided the basis for using green laser for underwater mapping are also discussed. The results of the laboratory and field experiments demonstrate the feasibility of using green laser for underwater infrastructure monitoring with limitations on the turbidity of water that affects the penetrability of the laser. This method can be used for scour monitoring around offshore structures in shallow water as well as corrosion monitoring of bridges.
- Open Access
Feasibility of Using Green Laser in Monitoring Local Scour around Bridge Pier
Scour around bridge piers is considered as one of the major factors which causes failure of bridges in the United States. An undetected scour can affect the stability of the bridge, eventually leading to the collapse of the bridge. The experimental investigation of scour around a pier using a non-contact measuring method is carried out in this research. A green laser-based non-contact ranging technique is performed on a prefabricated scour hole to study the factors influencing the ability to reconstruct the shape of a scour hole. The experiment was conducted in a 10 ft diameter pool and Leica scan station II was used for the scanning of the scour hole. The turbidity of the water was changed by adding Kaolinite powder to the water. The turbidity was varied from 1.2 NTU to 20.8 NTU by adding Kaolinite. The lab experiments involved changing the turbidity of water to simulate real world conditions. The results from the experimental study show that the turbidity of the water has a direct dependence on the efficiency of the green laser to map the underwater scour profile. The ability of the green laser to capture the fabricated scour hole and pool bed topography were decreased as the turbidity was increased even when the water depth of the pool was reduced. The results from the study show that the green laser is effective in underwater scanning and can be also used for bathymetry profiling and the detection of underwater objects. The method of underwater scanning using a green laser for detecting scour around bridge pier is safe, efficient, and economical.
Open AccessFeasibility of Using Green Laser in Monitoring Local Scour around Bridge Pier
Scour around bridge piers is considered as one of the major factors which causes failure of bridges in the United States. An undetected scour can affect the stability of the bridge, eventually leading to the collapse of the bridge. The experimental investigation of scour around a pier using a non-contact measuring method is carried out in this research. A green laser-based non-contact ranging technique is performed on a prefabricated scour hole to study the factors influencing the ability to reconstruct the shape of a scour hole. The experiment was conducted in a 10 ft diameter pool and Leica scan station II was used for the scanning of the scour hole. The turbidity of the water was changed by adding Kaolinite powder to the water. The turbidity was varied from 1.2 NTU to 20.8 NTU by adding Kaolinite. The lab experiments involved changing the turbidity of water to simulate real world conditions. The results from the experimental study show that the turbidity of the water has a direct dependence on the efficiency of the green laser to map the underwater scour profile. The ability of the green laser to capture the fabricated scour hole and pool bed topography were decreased as the turbidity was increased even when the water depth of the pool was reduced. The results from the study show that the green laser is effective in underwater scanning and can be also used for bathymetry profiling and the detection of underwater objects. The method of underwater scanning using a green laser for detecting scour around bridge pier is safe, efficient, and economical.
- Open Access
- 7 July 2022
- Published by MDPI AG in Geotechnics
- Vol. 2 (3) , 570-598
Energy-Based Approach: Analysis of a Laterally Loaded Pile in Multi-Layered Non-Linear Elastic Soil Strata
Several studies have been reported in published literature on analytical solutions for a laterally loaded pile installed in a homogeneous single soil layer. However, piles are rarely installed in an ideal homogeneous single soil layer. The present study describes a new continuum-based analysis or energy-based approach for predicting the pile displacement responses subjected to static lateral loads and moments considering the soil non-linearity. This analytical analysis treats the pile as an elastic Euler–Bernoulli beam and the soil as a three-dimensional (3D) continuum in which the non-linear elastic properties are described by a modulus degradation relationship. The principle of virtual work was applied to the energy equation of a pile–soil system in order to obtain the governing differential equation for the pile and soil displacements. An iterative procedure was adopted to solve the equations numerically using a finite difference method (FDM). The pile displacement response was obtained using the software MATLAB R2021a, and the results from the energy-based method were compared with those obtained from the field test data as well as the finite element analysis (FEA) based on the software ANSYS Workbench 2021R1. The present study investigated the effect of explicit incorporation of soil properties and layering through a parametric study in order to understand the importance of predicting appropriate pile displacement responses in a linear elastic soil system. The responses indicated that the effect of soil layers and their thicknesses, pile properties and the variation in soil moduli have a direct impact on the displacements of piles subjected to lateral loading. Hence, a proper emphasis has to be given to account for the soil non-linearity. Considering the effect of soil non-linearity, it is observed that the results obtained from the energy-based method agreed well with the field measured values and those obtained from the FEA. The results indicated a difference of approximately less than 7% between the proposed method and the FEA. The approach presented in this study can be further extended to piles embedded in multi-layered soil strata subjected to the combined action of axial loads, lateral loads and moments. Furthermore, the same approach can be extended to study the response of the soil to group piles.
- 7 July 2022
- Published by MDPI AG in Geotechnics
- Vol. 2 (3) , 570-598
Open AccessEnergy-Based Approach: Analysis of a Laterally Loaded Pile in Multi-Layered Non-Linear Elastic Soil Strata
Several studies have been reported in published literature on analytical solutions for a laterally loaded pile installed in a homogeneous single soil layer. However, piles are rarely installed in an ideal homogeneous single soil layer. The present study describes a new continuum-based analysis or energy-based approach for predicting the pile displacement responses subjected to static lateral loads and moments considering the soil non-linearity. This analytical analysis treats the pile as an elastic Euler–Bernoulli beam and the soil as a three-dimensional (3D) continuum in which the non-linear elastic properties are described by a modulus degradation relationship. The principle of virtual work was applied to the energy equation of a pile–soil system in order to obtain the governing differential equation for the pile and soil displacements. An iterative procedure was adopted to solve the equations numerically using a finite difference method (FDM). The pile displacement response was obtained using the software MATLAB R2021a, and the results from the energy-based method were compared with those obtained from the field test data as well as the finite element analysis (FEA) based on the software ANSYS Workbench 2021R1. The present study investigated the effect of explicit incorporation of soil properties and layering through a parametric study in order to understand the importance of predicting appropriate pile displacement responses in a linear elastic soil system. The responses indicated that the effect of soil layers and their thicknesses, pile properties and the variation in soil moduli have a direct impact on the displacements of piles subjected to lateral loading. Hence, a proper emphasis has to be given to account for the soil non-linearity. Considering the effect of soil non-linearity, it is observed that the results obtained from the energy-based method agreed well with the field measured values and those obtained from the FEA. The results indicated a difference of approximately less than 7% between the proposed method and the FEA. The approach presented in this study can be further extended to piles embedded in multi-layered soil strata subjected to the combined action of axial loads, lateral loads and moments. Furthermore, the same approach can be extended to study the response of the soil to group piles.
- Open Access
- 6 July 2022
- Published by MDPI AG in Geotechnics
- Vol. 2 (3) , 549-569
Energy-Based Approach: Analysis of a Vertically Loaded Pile in Multi-Layered Non-Linear Soil Strata
Numerous studies have been reported in the published literature on analytical solutions for a vertically loaded pile installed in a homogeneous single soil layer. However, piles are rarely installed in an ideal homogeneous single soil layer. This study presents an analytical model based on the energy-based approach to obtain displacements in an axially loaded pile embedded in multi-layered soil considering soil non-linearity. The developed analytical model incorporating Euler-Bernoulli beam theory proved to be an effective way in estimating the load-displacement responses of piles embedded in multi-layered non-linear elastic soil strata. The differential equations are solved analytically and numerically using the variational principle of mechanics. A parametric study investigated the effect of explicit incorporation of soil properties and layering in order to understand the importance of predicting appropriate pile displacement responses in linear elastic soil system. It is clear from the results that the analyses which consider the soil as a single homogeneous layer will not be able to produce an accurate estimation of the pile stiffnesses. Therefore, it is highly important to account for the effect of soil layering and the non-linear response. The pile displacement response is obtained using the software MATLAB R2019a and the results from the energy-based method are compared with those obtained from the field test data as well as the Finite Element Analysis (FEA) based on the software ANSYS 2019R3. The non-linear elastic constitutive relationship which described the variation of secant shear modulus with strain through a power law has shown reasonably accurate predictions when compared to the published field test data and the FEA. The developed mathematical framework is also more computationally efficient than the three-dimensional (3D) FEA.
- 6 July 2022
- Published by MDPI AG in Geotechnics
- Vol. 2 (3) , 549-569
Open AccessEnergy-Based Approach: Analysis of a Vertically Loaded Pile in Multi-Layered Non-Linear Soil Strata
Numerous studies have been reported in the published literature on analytical solutions for a vertically loaded pile installed in a homogeneous single soil layer. However, piles are rarely installed in an ideal homogeneous single soil layer. This study presents an analytical model based on the energy-based approach to obtain displacements in an axially loaded pile embedded in multi-layered soil considering soil non-linearity. The developed analytical model incorporating Euler-Bernoulli beam theory proved to be an effective way in estimating the load-displacement responses of piles embedded in multi-layered non-linear elastic soil strata. The differential equations are solved analytically and numerically using the variational principle of mechanics. A parametric study investigated the effect of explicit incorporation of soil properties and layering in order to understand the importance of predicting appropriate pile displacement responses in linear elastic soil system. It is clear from the results that the analyses which consider the soil as a single homogeneous layer will not be able to produce an accurate estimation of the pile stiffnesses. Therefore, it is highly important to account for the effect of soil layering and the non-linear response. The pile displacement response is obtained using the software MATLAB R2019a and the results from the energy-based method are compared with those obtained from the field test data as well as the Finite Element Analysis (FEA) based on the software ANSYS 2019R3. The non-linear elastic constitutive relationship which described the variation of secant shear modulus with strain through a power law has shown reasonably accurate predictions when compared to the published field test data and the FEA. The developed mathematical framework is also more computationally efficient than the three-dimensional (3D) FEA.
- Open Access
- 30 April 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (5) , 612
Coastal Protection Using Integration of Mangroves with Floating Barges: An Innovative Concept
Mangroves and moored barges are used individually for coastal protection and beach restoration. This conceptual paper discusses about the integration of mangroves with moored floating barges for coastal protection. The concept involves towing of a barge to a particular location, mooring it to the seafloor and planting mangroves along the shore or beach. The barges will be unmoored and towed away once the mangroves attain certain growth and are well rooted in the soil. Mangroves can protect the beach from incoming waves using their roots and branches. The incoming waves can be reduced by 50% to 99% using mangroves of 500 m width. Mangroves have a life span of 20–100 years, and they do not need any yearly maintenance as do any other conventional coastal protection measures. Mangroves are considered as soft coastal protection structures and are environmentally friendly. Mangroves will also improve the aesthetic appearance of the beach. This paper discusses about some of the research methodologies for the development of the barge-assisted mangroves coastal protection method. The dimensions of the barge, gap width between the moored barges and the environmental condition at the location determines the performance of the barge-assisted mangroves coastal protection method. The gap width between the barges, draft of the barge and breadth of the barge influence the resonant frequency of the fluid between the barges. The shielding effect of the floating barges can be used for other applications, such as berthing of ships and growing living shorelines using oysters, rocks, sand, plants, coir, etc. for coastal protection.
- 30 April 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (5) , 612
Open AccessCoastal Protection Using Integration of Mangroves with Floating Barges: An Innovative Concept
Mangroves and moored barges are used individually for coastal protection and beach restoration. This conceptual paper discusses about the integration of mangroves with moored floating barges for coastal protection. The concept involves towing of a barge to a particular location, mooring it to the seafloor and planting mangroves along the shore or beach. The barges will be unmoored and towed away once the mangroves attain certain growth and are well rooted in the soil. Mangroves can protect the beach from incoming waves using their roots and branches. The incoming waves can be reduced by 50% to 99% using mangroves of 500 m width. Mangroves have a life span of 20–100 years, and they do not need any yearly maintenance as do any other conventional coastal protection measures. Mangroves are considered as soft coastal protection structures and are environmentally friendly. Mangroves will also improve the aesthetic appearance of the beach. This paper discusses about some of the research methodologies for the development of the barge-assisted mangroves coastal protection method. The dimensions of the barge, gap width between the moored barges and the environmental condition at the location determines the performance of the barge-assisted mangroves coastal protection method. The gap width between the barges, draft of the barge and breadth of the barge influence the resonant frequency of the fluid between the barges. The shielding effect of the floating barges can be used for other applications, such as berthing of ships and growing living shorelines using oysters, rocks, sand, plants, coir, etc. for coastal protection.
- Open Access
- 16 July 2021
- Published by ASME International
Numerical Investigation on Wave Transmission by a Submerged Reef Using Mike 3 Wave Fm
Submerged reefs are multi-purpose man-made structures for coastal protection, surfing, improvement of marine life and blocking passage of ships and trawling nets. Artificial reef is considered as an effective way in preventing coastal erosion due to its multipurpose benefits. Submerged reefs dissipate the incoming wave energy by forcing waves to break on top of the reef thereby
- 16 July 2021
- Published by ASME International
Open AccessNumerical Investigation on Wave Transmission by a Submerged Reef Using Mike 3 Wave Fm
Submerged reefs are multi-purpose man-made structures for coastal protection, surfing, improvement of marine life and blocking passage of ships and trawling nets. Artificial reef is considered as an effective way in preventing coastal erosion due to its multipurpose benefits. Submerged reefs dissipate the incoming wave energy by forcing waves to break on top of the reef thereby
- Open Access
- 16 July 2021
- Published by ASME International
Integrated Probabilistic-Mechanistic Deterioration Modeling for Preventive Maintenance of Aging Fixed Offshore Jacket-Type Platforms
Most of the offshore platforms in the world are designed as steel jacket-type platforms for oil and gas exploration and production. Jackets are fixed offshore platforms that are used in shallow-medium deep waters where the water depth may not exceed 500 meters. Based on the 2018 report, many offshore platforms in the Gulf of Mexico and the North Sea are more than 40 years old, and
- 16 July 2021
- Published by ASME International
Open AccessIntegrated Probabilistic-Mechanistic Deterioration Modeling for Preventive Maintenance of Aging Fixed Offshore Jacket-Type Platforms
Most of the offshore platforms in the world are designed as steel jacket-type platforms for oil and gas exploration and production. Jackets are fixed offshore platforms that are used in shallow-medium deep waters where the water depth may not exceed 500 meters. Based on the 2018 report, many offshore platforms in the Gulf of Mexico and the North Sea are more than 40 years old, and
- 1 October 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 21 (5)
High Creep Stress Test of Carbon Fiber–Composite Cable with Generic Field-Made Anchorage
Carbon fiber–reinforced polymer (CFRP) tendons can serve as a viable alternative to steel strands in prestressing applications in which the noncorrosive nature of the strands helps reduce maintenance costs and extend the service life of the structure. An important consideration for CFRP tendons is the prestress level, which is currently limited by prevailing standards. A series of creep stress tests were conducted on carbon fiber–composite cables with generic field-made anchorages using commercially available expansive grout. Specimens withstood 95% of their guaranteed capacity for a period of five months (3,624 h) at a room temperature of 24°C (75°F) without rupture or any sign of distress. The experiments also showed quite an acceptable long-term performance for the generic field-made anchorage. In subsequent residual strength tests, all specimens still exceeded their guaranteed capacity after the extended high creep stress test.
- 1 October 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Composites for Construction
- Vol. 21 (5)
High Creep Stress Test of Carbon Fiber–Composite Cable with Generic Field-Made Anchorage
Carbon fiber–reinforced polymer (CFRP) tendons can serve as a viable alternative to steel strands in prestressing applications in which the noncorrosive nature of the strands helps reduce maintenance costs and extend the service life of the structure. An important consideration for CFRP tendons is the prestress level, which is currently limited by prevailing standards. A series of creep stress tests were conducted on carbon fiber–composite cables with generic field-made anchorages using commercially available expansive grout. Specimens withstood 95% of their guaranteed capacity for a period of five months (3,624 h) at a room temperature of 24°C (75°F) without rupture or any sign of distress. The experiments also showed quite an acceptable long-term performance for the generic field-made anchorage. In subsequent residual strength tests, all specimens still exceeded their guaranteed capacity after the extended high creep stress test.