Oleksandr Povstyanoy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oleksandr Povstyanoy has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Nataliia Imbirovych
Lutsk National Technical University
11 shared publications - Rostyslav Redko
Lutsk National Technical University
6 shared publications - Olha Zaleta
Lutsk National Technical University
5 shared publications - Roman Obertyukh
Vinnytsia National Technical University
4 shared publications - Roman Polinkevych
Lutsk National Technical University
4 shared publications - Taras Chetverzhuk
Lutsk National Technical University
4 shared publications
Latest Publications
- Open Access
- 14 October 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (2) , B13
Technological Assurance of the Quality of Roller Bearing Ring End Surfaces
The study examines the face grinding of outer rings for 32017-X tapered roller bearing made of LH15 steel with a hardness of 55–64 НRC. A scientific and practical approach was proposed to solve the current problem of ensuring the required quality of bearing workpieces. It was established that the disadvantages of traditional grinding methods for such workpieces include difficulty in achieving the required accuracy and physical-mechanical characteristics: non-parallelism of the end faces of 8–12 μm, surface roughness up to 1.25 μm, surface burns, and reduced hardness. It was proposed to use an intermittent grinding tool with pressurized delivery of cutting fluid through the wheel grooves, as a more rational method than the conventional continuous wheel grinding with flood cooling used in production. Experimental results revealed the technological advantages of the proposed machining: end face roughness improved by 0.4–0.6 μm, parallelism by 2–3 μm, and no surface grinding burns were observed. The surface layer hardness after intermittent wheel grinding increased from 60 to 64 HRC. In the study of the surface microprofile formation during intermittent grinding, the roughness of about 0.1–0.6 μm was ensured at the following parameters: workpiece speed of 4.0–6.0 m/min, cutting depth of 0.1–0.3 mm, and cutting speed of 28‒30 m/s. Minimum non-parallelism values for the ring end faces were achieved with an allowance of 0.2–0.3 mm. The proposed face grinding of bearing rings using an intermittent wheel reduced labor intensity and machining costs by a factor of 1.5–2.0 by combining roughing and reducing energy consumption by 35–40 %. Furthermore, it fully ensured the specified quality and accuracy parameters for the bearing ring outer end faces and is effective for machining large-scale surfaces on both universal and automated machine tools.
- 14 October 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (2) , B13
Open AccessTechnological Assurance of the Quality of Roller Bearing Ring End Surfaces
The study examines the face grinding of outer rings for 32017-X tapered roller bearing made of LH15 steel with a hardness of 55–64 НRC. A scientific and practical approach was proposed to solve the current problem of ensuring the required quality of bearing workpieces. It was established that the disadvantages of traditional grinding methods for such workpieces include difficulty in achieving the required accuracy and physical-mechanical characteristics: non-parallelism of the end faces of 8–12 μm, surface roughness up to 1.25 μm, surface burns, and reduced hardness. It was proposed to use an intermittent grinding tool with pressurized delivery of cutting fluid through the wheel grooves, as a more rational method than the conventional continuous wheel grinding with flood cooling used in production. Experimental results revealed the technological advantages of the proposed machining: end face roughness improved by 0.4–0.6 μm, parallelism by 2–3 μm, and no surface grinding burns were observed. The surface layer hardness after intermittent wheel grinding increased from 60 to 64 HRC. In the study of the surface microprofile formation during intermittent grinding, the roughness of about 0.1–0.6 μm was ensured at the following parameters: workpiece speed of 4.0–6.0 m/min, cutting depth of 0.1–0.3 mm, and cutting speed of 28‒30 m/s. Minimum non-parallelism values for the ring end faces were achieved with an allowance of 0.2–0.3 mm. The proposed face grinding of bearing rings using an intermittent wheel reduced labor intensity and machining costs by a factor of 1.5–2.0 by combining roughing and reducing energy consumption by 35–40 %. Furthermore, it fully ensured the specified quality and accuracy parameters for the bearing ring outer end faces and is effective for machining large-scale surfaces on both universal and automated machine tools.
- 4 October 2026
- Published by Springer Nature
- p. 95-106
Theoretical Study of the Influence of the Thermal Conductivity Coefficient of Tool Material During the Cutting of Bone Substances
- 4 October 2026
- Published by Springer Nature
- p. 95-106
Theoretical Study of the Influence of the Thermal Conductivity Coefficient of Tool Material During the Cutting of Bone Substances
- Open Access
- 24 September 2026
- Published by Scilight Press Pty Ltd in Journal of Mechanical Engineering and Manufacturing
Mathematical Modelling of a Pneumo-Hydraulic Impulse Device for Vibration Turning
This paper addresses the critical challenge of improving the machinability of difficult-to-cut advanced materials through radial vibration-assisted turning. Traditional piezoelectric or mechanical vibrators suffer from micro-stroke decay or severe inertial limitations under heavy technological cutting loads. To resolve this bottleneck, a compact pneumo-hydraulic impulse multiplier device equipped with a single-stage parametric pressure pulse generator is investigated via a non-linear fluid-structure interaction framework solved through explicit Euler integration. Initial simulations revealed that a conventional high-inertia steel pusher (0.85 kg) paired with standard cylindrical springs induces a destructive “static lock-up” condition due to continuous unrelaxed kinetic energy accumulation. To bring the drive into its optimal operating window, structural modernization was executed by substituting the reciprocating components with a lightweight titanium alloy (Ti-6Al-4V Grade 5) and integrating a high-stiffness slotted spring. The upgraded simulation demonstrates a successful transition into a critically damped aperiodic operating regime. The modernized drive completely eliminates parasitic tool rebound, achieving perfectly repeatable pressure cycles reaching 14.8 MPa and a highly stable cutter vibration amplitude of 0.15–0.18 mm at operating frequencies up to 250 Hz. This provides a predictive, numerically validated foundation for high-frequency vibration turning utilizing standard shop-floor pneumatic supply networks.
- 24 September 2026
- Published by Scilight Press Pty Ltd in Journal of Mechanical Engineering and Manufacturing
Open AccessMathematical Modelling of a Pneumo-Hydraulic Impulse Device for Vibration Turning
This paper addresses the critical challenge of improving the machinability of difficult-to-cut advanced materials through radial vibration-assisted turning. Traditional piezoelectric or mechanical vibrators suffer from micro-stroke decay or severe inertial limitations under heavy technological cutting loads. To resolve this bottleneck, a compact pneumo-hydraulic impulse multiplier device equipped with a single-stage parametric pressure pulse generator is investigated via a non-linear fluid-structure interaction framework solved through explicit Euler integration. Initial simulations revealed that a conventional high-inertia steel pusher (0.85 kg) paired with standard cylindrical springs induces a destructive “static lock-up” condition due to continuous unrelaxed kinetic energy accumulation. To bring the drive into its optimal operating window, structural modernization was executed by substituting the reciprocating components with a lightweight titanium alloy (Ti-6Al-4V Grade 5) and integrating a high-stiffness slotted spring. The upgraded simulation demonstrates a successful transition into a critically damped aperiodic operating regime. The modernized drive completely eliminates parasitic tool rebound, achieving perfectly repeatable pressure cycles reaching 14.8 MPa and a highly stable cutter vibration amplitude of 0.15–0.18 mm at operating frequencies up to 250 Hz. This provides a predictive, numerically validated foundation for high-frequency vibration turning utilizing standard shop-floor pneumatic supply networks.
- Open Access
- 1 April 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (1) , F1
Mathematical Modeling of a Small-Dimension Hydropulse Vibrator with a Valve-Driven Pressure Pulse Generator
The article presents research on a new compact vibrator design based on a hydraulic pulse drive with a built-in valve-type pressure pulse generator. Based on scientific assumptions, an approximate cycle diagram of the working cycle, a structural diagram of the vibrator, and a representation of the hydraulic link of its hydraulic system as a Kelvin–Voigt model were developed. A dynamic model of the vibrator was designed, in which the hydraulic link interacts with the moving links via transmission ratios. Based on simplified dynamic models of the forward and reverse strokes of the executive element, a mathematical model of the vibrator was developed using the d’Alembert principle, resulting in a system of 2nd-order differential equations describing the motion of the executive element’s mass during its forward and reverse strokes. Consumption for energy equations at time intervals was also considered according to the approximate cycle diagram of the vibrator’s working cycle and the conditions of uniqueness that limit the movement of the mass of the executive element and the deformation of the hydraulic link. To provide a detailed analysis of the developed mathematical model, Python program code was written. The workflow was visualized in Google Colab. It was confirmed that the operating frequency range of a hydraulic pulse vibrator of this design is not a single fixed number – it is parametric and depends on the settings of the hydraulic system. By adjusting the pumping station parameters and the stiffness of the vibrator’s elastic elements, it is possible to achieve an actuator frequency up to 150 Hz and an amplitude of up to 2 mm.
- 1 April 2026
- Published by Sumy State University in Journal of Engineering Sciences
- Vol. 13 (1) , F1
Open AccessMathematical Modeling of a Small-Dimension Hydropulse Vibrator with a Valve-Driven Pressure Pulse Generator
The article presents research on a new compact vibrator design based on a hydraulic pulse drive with a built-in valve-type pressure pulse generator. Based on scientific assumptions, an approximate cycle diagram of the working cycle, a structural diagram of the vibrator, and a representation of the hydraulic link of its hydraulic system as a Kelvin–Voigt model were developed. A dynamic model of the vibrator was designed, in which the hydraulic link interacts with the moving links via transmission ratios. Based on simplified dynamic models of the forward and reverse strokes of the executive element, a mathematical model of the vibrator was developed using the d’Alembert principle, resulting in a system of 2nd-order differential equations describing the motion of the executive element’s mass during its forward and reverse strokes. Consumption for energy equations at time intervals was also considered according to the approximate cycle diagram of the vibrator’s working cycle and the conditions of uniqueness that limit the movement of the mass of the executive element and the deformation of the hydraulic link. To provide a detailed analysis of the developed mathematical model, Python program code was written. The workflow was visualized in Google Colab. It was confirmed that the operating frequency range of a hydraulic pulse vibrator of this design is not a single fixed number – it is parametric and depends on the settings of the hydraulic system. By adjusting the pumping station parameters and the stiffness of the vibrator’s elastic elements, it is possible to achieve an actuator frequency up to 150 Hz and an amplitude of up to 2 mm.
- 17 January 2026
- Published by Springer Nature
- p. 74-86
Automation of Warehouse Parameters Calculation and Its Sketch Design
- 17 January 2026
- Published by Springer Nature
- p. 74-86
Automation of Warehouse Parameters Calculation and Its Sketch Design
- 17 January 2026
- Published by Springer Nature
- p. 427-438
Using Plasma Electrolytic Oxidation Technologies in the Manufacture with Better Biodesign
- 17 January 2026
- Published by Springer Nature
- p. 427-438
Using Plasma Electrolytic Oxidation Technologies in the Manufacture with Better Biodesign
- 1 January 2026
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 131 (1) , 32-38
Theoretical research of a new design of a parametric pressure pulse generator for a vibratory hydraulic drive
Based on the results of the analysis of known circuit and structural designs of pressure pulse generators (PPG) in liquid, a new design of a single-stage parametric PPG with increased throughput capacity has been developed according to the connection diagram to the executive hydraulic cylinder of the hydraulic pulse drive (HPD) «at the inlet», the distribution links (first and second sealing stages) of which are combined with a high-rigidity slotted spring (SS). The newly designed PPG is used to control the HPD with a parametric-type actuating hydraulic cylinder. In order to create a scientifically sound methodology for the design calculation of the studied hydraulic impulse drive and PPG, a dynamic model of the HPD was developed, based on which and a sound structure of assumptions, a mathematical model of the HPD was constructed and analysed.
- 1 January 2026
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 131 (1) , 32-38
Theoretical research of a new design of a parametric pressure pulse generator for a vibratory hydraulic drive
Based on the results of the analysis of known circuit and structural designs of pressure pulse generators (PPG) in liquid, a new design of a single-stage parametric PPG with increased throughput capacity has been developed according to the connection diagram to the executive hydraulic cylinder of the hydraulic pulse drive (HPD) «at the inlet», the distribution links (first and second sealing stages) of which are combined with a high-rigidity slotted spring (SS). The newly designed PPG is used to control the HPD with a parametric-type actuating hydraulic cylinder. In order to create a scientifically sound methodology for the design calculation of the studied hydraulic impulse drive and PPG, a dynamic model of the HPD was developed, based on which and a sound structure of assumptions, a mathematical model of the HPD was constructed and analysed.
- 14 February 2025
- Published by Springer Nature
- p. 423-433
Formation of Coatings on Titanium Alloys Saturated with Biocomponents by the PEO Method
- 14 February 2025
- Published by Springer Nature
- p. 423-433
Formation of Coatings on Titanium Alloys Saturated with Biocomponents by the PEO Method
- Open Access
- 1 January 2025
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 130 (4) , 43-53
Automated smart humanoid robot arm on the Arduino platform
The article presents the development of an automated smart humanoid robot hand on the Arduino platform using 3D printing, servo drives, and a sensor glove with flexible sensors. An electrical circuit and a software module for reading and processing signals have been developed, which provides real-time reproduction of the operator's finger movements. Modelling, assembly of mechanical and electronic parts, calibration of sensors and actuators have been carried out. Experimental studies have confirmed the accuracy, speed, and stability of the system, which makes it suitable for educational and demonstration robotics applications.
- 1 January 2025
- Published by Rzeszow University of Technology in Technologia i Automatyzacja Montażu
- Vol. 130 (4) , 43-53
Open AccessAutomated smart humanoid robot arm on the Arduino platform
The article presents the development of an automated smart humanoid robot hand on the Arduino platform using 3D printing, servo drives, and a sensor glove with flexible sensors. An electrical circuit and a software module for reading and processing signals have been developed, which provides real-time reproduction of the operator's finger movements. Modelling, assembly of mechanical and electronic parts, calibration of sensors and actuators have been carried out. Experimental studies have confirmed the accuracy, speed, and stability of the system, which makes it suitable for educational and demonstration robotics applications.