RORoman Obertyukh

Roman Obertyukh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Roman Obertyukh has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Mathematical Modelling of a Pneumo-Hydraulic Impulse Device for Vibration Turning

    by Roman Obertyukh, Andriiy Slabkyi, Oleksandr Povstyanoy, Dmytro Bakalets, Vladyslav Polishchuk

    This paper addresses the critical challenge of improving the machinability of difficult-to-cut advanced materials through radial vibration-assisted turning. Traditional piezoelectric or mechanical vibrators suffer from micro-stroke decay or severe inertial limitations under heavy technological cutting loads. To resolve this bottleneck, a compact pneumo-hydraulic impulse multiplier device equipped with a single-stage parametric pressure pulse generator is investigated via a non-linear fluid-structure interaction framework solved through explicit Euler integration. Initial simulations revealed that a conventional high-inertia steel pusher (0.85 kg) paired with standard cylindrical springs induces a destructive “static lock-up” condition due to continuous unrelaxed kinetic energy accumulation. To bring the drive into its optimal operating window, structural modernization was executed by substituting the reciprocating components with a lightweight titanium alloy (Ti-6Al-4V Grade 5) and integrating a high-stiffness slotted spring. The upgraded simulation demonstrates a successful transition into a critically damped aperiodic operating regime. The modernized drive completely eliminates parasitic tool rebound, achieving perfectly repeatable pressure cycles reaching 14.8 MPa and a highly stable cutter vibration amplitude of 0.15–0.18 mm at operating frequencies up to 250 Hz. This provides a predictive, numerically validated foundation for high-frequency vibration turning utilizing standard shop-floor pneumatic supply networks.

  • Open Access

    Mathematical Modeling of a Small-Dimension Hydropulse Vibrator with a Valve-Driven Pressure Pulse Generator

    by Roman Obertyukh, Andriі Slabkyі, Oleksandr Povstyanoy, Dmytro Bakalets, Vladyslav Polishuk

    The article presents research on a new compact vibrator design based on a hydraulic pulse drive with a built-in valve-type pressure pulse generator. Based on scientific assumptions, an approximate cycle diagram of the working cycle, a structural diagram of the vibrator, and a representation of the hydraulic link of its hydraulic system as a Kelvin–Voigt model were developed. A dynamic model of the vibrator was designed, in which the hydraulic link interacts with the moving links via transmission ratios. Based on simplified dynamic models of the forward and reverse strokes of the executive element, a mathematical model of the vibrator was developed using the d’Alembert principle, resulting in a system of 2nd-order differential equations describing the motion of the executive element’s mass during its forward and reverse strokes. Consumption for energy equations at time intervals was also considered according to the approximate cycle diagram of the vibrator’s working cycle and the conditions of uniqueness that limit the movement of the mass of the executive element and the deformation of the hydraulic link. To provide a detailed analysis of the developed mathematical model, Python program code was written. The workflow was visualized in Google Colab. It was confirmed that the operating frequency range of a hydraulic pulse vibrator of this design is not a single fixed number – it is parametric and depends on the settings of the hydraulic system. By adjusting the pumping station parameters and the stiffness of the vibrator’s elastic elements, it is possible to achieve an actuator frequency up to 150 Hz and an amplitude of up to 2 mm.

  • Open Access

    Method of design calculation of a parametric single-stage pressure pulse generator with adjustable pressure "closing"

    by Roman Obertykh, Andrіі Slabkyі, Serhii Kotyk, Віталій Олександрович Кудраш, Dmytro Bakalets, Андрій Валентинович Слабкий, Сергій Іванович Котик, Дмитро Віталійович Бакалець

    On the basis of a qualitative analysis of the structure and principle of operation of a parametric single-stage pressure pulse generator with adjustable pressure "closing" p2, the design of a prototype of the generator was developed. The article describes the principle of operation of the developed structure and describes the design of structural elements and their interaction with other structural elements from the justification. The design calculation methodology is developed on the basis of generally accepted engineering and scientific principles and experience in the design and operation of equipment based on pneumatic and hydropulse drive of vibration and vibration shock machines. The paper presents a sample of initial data that is necessary for the development of a design calculation methodology for a parametric single-stage pressure pulse generator with adjustable "closing" pressure p2. Based on the analysis of the design of the prototype of the generator, the accepted initial (input) data and the experience of designing a hydropulse drive and pressure pulse generators given in the literature sources, a method of design calculation of a parametric single-stage pressure pulse generator with adjustable pressure "closing" p2 has been developed and its main energy, power and geometric parameters of the design of the prototype of both a hydropulse drive and a generator have been determined pressure pulses. The presented mathematical dependencies allow you to change the parameters of the pressure pulse generator to the corresponding technical and economic parameters of the technological process. The paper also substantiates the use of the concept of "cyclic pressure pulse coefficient", the exact value of which can be found only based on the results of experimental studies of a prototype of a pressure pulse generator. For the design calculation, based on the recommendations of the researchers of the hydropulse drive, a margin factor within 10 ... 25 percent of the face value.

  • Theoretical research of a new design of a parametric pressure pulse generator for a vibratory hydraulic drive

    by Roman Obertyukh, Andrii Slabkyi, Oleksandr Povstyanoy, Sergey Sukhorukov, Sergey Kotyk

    Based on the results of the analysis of known circuit and structural designs of pressure pulse generators (PPG) in liquid, a new design of a single-stage parametric PPG with increased throughput capacity has been developed according to the connection diagram to the executive hydraulic cylinder of the hydraulic pulse drive (HPD) «at the inlet», the distribution links (first and second sealing stages) of which are combined with a high-rigidity slotted spring (SS). The newly designed PPG is used to control the HPD with a parametric-type actuating hydraulic cylinder. In order to create a scientifically sound methodology for the design calculation of the studied hydraulic impulse drive and PPG, a dynamic model of the HPD was developed, based on which and a sound structure of assumptions, a mathematical model of the HPD was constructed and analysed.

  • Open Access

    Hydroimpulse drive of a vibration press with a two-stage five-line pressure impulse generator with parametric control of its second stage

    by Roman Obertykh, Andrіі Slabkyі, Vasyl Ishchenko

    Analysis of theoretical and experimental studies of the hydraulic pulse drive of technological vibration and vi-bration-impact machines (vibratory cutting and deformation strengthening of machine part surfaces, hydro-pulse vibrators, etc.) showed that the hydro-pulse drive allows for the implementation of various vibration technologies in a wide range of technical applications and with adjustable vibration loads on objects of technological influence. Based on the results of a theoretical study of existing designs of vibration press equipment based on a hydraulic pulse drive, a schematic and structural diagram of a hydraulic pulse vibration press with a two-stage five-line pressure pulse generator with parametric control of its second cascade and an executive link with a drive of the vibrating table of the vibropress from a piston hydraulic cylinder and a load of the object of technological influence of the hydraulic pulse drive from a plunger hydraulic cylinder, the body of which is installed on the architrave of the vibrating press, and the plunger is kinematically connected to the movable crossbeam of the vibrating press. The article presents a description of the operation of a newly developed design of a hydraulic pulse vibrating press with a two-stage five-line pressure pulse generator with parametric control of its second stage, and provides the main calculation dependencies according to which the main geometric and force parameters of the developed drive design can be calculated. This design solution expands the technical and technological capabilities of the hydraulic pulse drive, as it provides a high-speed mode of vibration movement of the executive link – the vibration table of the vibration press in combination with the hydraulic load of the object of technological influence from an additional plunger hydraulic cylinder installed on the architrave of the vibration press, the plunger of which drives the movable crossbeam of the vibration press.

  • Open Access

    DYNAMIC AND MATHEMATICAL MODELS OF THE HYDROIMPULSIVE VIBRO-CUTTING DEVICE WITH A PRESSURE PULSE GENERATOR BULT INTO THE RING SPRING

    by Roman Obertyukh, Andrіі Slabkyі, Leonid Polishchuk, Oleksandr Povstianoi, Saule Kumargazhanova, Maxatbek Satymbekov

    Structural calculation scheme of the hydropulse device for vibration cutting with built-in ring with pressure pulse generator (PPG) is considered. On the basis of the structural scheme and cyclogram of the working cycle of the device, its dynamic and mathematical models were developed, in which the hydraulic link is represented by a visco-elastic model of the working fluid (energy carrier) composed of the inertial elastic and dissipative elements (Kelvin-Foyga's body).


  • Substantiation of the Design Calculation Method for the Vibroturning Device

    by Roman Obertyukh, Andrii Slabkyi, Oleksandr Petrov, Dmytro Bakalets, Sergey Sukhorukov


  • Mathematical Modeling of the Device for Radial Vibroturning

    by Roman Obertyukh, Andrii Slabkyi, Oleksandr Petrov, Vitalii Kudrash


  • Method of design calculation of a hydropulse device for strain hardening of materials

    by Roman Obertyukh

    Wydawnictwo SIGMA-NOT wydaje czasopisma fachowe informuj?ce swoich czytelnik?w o najnowszych osi?gni?ciach naukowych i nowoczesnych rozwi?zaniach technicznych w Polsce i na ?wiecie, popularyzuje problemy techniczne oraz poszerza wiedz? i kultur? techniczn?.