Jingyi Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jingyi Wu has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Guang Yang
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, China
27 shared publications - Yonghua Huang
Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University 1 , Shanghai 200240
7 shared publications Guang Yang
4 shared publicationsYe Wang
4 shared publicationsAifeng Cai
3 shared publications- Chunyu Li
Institute of Refrigeration and Cryogenic, Shanghai Jiao Tong University 1 , Shanghai 200240
3 shared publications
Latest Publications
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Jet-driven depressurization and thermal homogenization in cryogenic propellant tanks: A multi-scale experimental and numerical study
Despite extensive studies on spray-bar thermodynamic venting system, the coupled effects of jet axial distribution, circulation flow rate, and subcooling on the dynamic interplay between depressurization and thermal homogenization under partial-fill conditions remain poorly understood, particularly regarding the competition between condensation-driven and mixing-driven mechanisms. An experimental and numerical study is conducted to investigate the two-phase flow dynamics and associated thermal-hydraulic behaviors during jet-induced mixing, depressurization, and temperature homogenization in a cryogenic tank. A numerical framework is established using the volume-of-fluid method combined with the shear stress transport k–ω turbulence model to resolve the interfacial two-phase flow and transport processes. The Eulerian–Lagrangian approach is adopted to track the jet droplet trajectories and to account for droplet–vapor, droplet–droplet, and droplet–wall interactions in the two-phase system. A series of parametric jetting experiments is performed to measure the transient pressure and temperature responses. High-speed flow visualization is used to record the jet-induced two-phase flow structures inside the tank. The model is validated against experimental data. The effects of axial jet distribution, jet flow rate, and jet subcooling on the flow development, depressurization, and thermal homogenization are examined. It is found that jet injection within the vapor-phase zone enhances interfacial mass exchange and improves depressurization efficiency. The thermal field near the tank wall is strongly affected by jet parameters. Higher jet flow rates and temperatures promote vapor-phase condensation, thereby accelerating the pressure decay. This work improves the physical understanding of jet-driven two-phase flow and transport in cryogenic storage systems.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Jet-driven depressurization and thermal homogenization in cryogenic propellant tanks: A multi-scale experimental and numerical study
Despite extensive studies on spray-bar thermodynamic venting system, the coupled effects of jet axial distribution, circulation flow rate, and subcooling on the dynamic interplay between depressurization and thermal homogenization under partial-fill conditions remain poorly understood, particularly regarding the competition between condensation-driven and mixing-driven mechanisms. An experimental and numerical study is conducted to investigate the two-phase flow dynamics and associated thermal-hydraulic behaviors during jet-induced mixing, depressurization, and temperature homogenization in a cryogenic tank. A numerical framework is established using the volume-of-fluid method combined with the shear stress transport k–ω turbulence model to resolve the interfacial two-phase flow and transport processes. The Eulerian–Lagrangian approach is adopted to track the jet droplet trajectories and to account for droplet–vapor, droplet–droplet, and droplet–wall interactions in the two-phase system. A series of parametric jetting experiments is performed to measure the transient pressure and temperature responses. High-speed flow visualization is used to record the jet-induced two-phase flow structures inside the tank. The model is validated against experimental data. The effects of axial jet distribution, jet flow rate, and jet subcooling on the flow development, depressurization, and thermal homogenization are examined. It is found that jet injection within the vapor-phase zone enhances interfacial mass exchange and improves depressurization efficiency. The thermal field near the tank wall is strongly affected by jet parameters. Higher jet flow rates and temperatures promote vapor-phase condensation, thereby accelerating the pressure decay. This work improves the physical understanding of jet-driven two-phase flow and transport in cryogenic storage systems.
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Experimental study on equilibrium height of capillary rise with liquid oxygen in reduced gravity under the influence of thermal leakage
Cryogenic propellants often experience reduced-gravity levels during orbital transfer and deep exploration, which leads to uncertainty in their interface structure and equilibrium height. In addition, unexpected thermal leakage can cause evaporation at the three-phase contact line, further complicating the prediction of the interface location. In this research, a cryogenic testing apparatus based on a magnetic compensation platform was developed to investigate the capillary rise equilibrium height on a plate and in the corner of liquid oxygen (LOX) in reduced gravity. A periscope-like visual system is employed to visualize and record the interface evolution in the magnetic compensation region. It is found that wall overheat leads to a decrease in the steady-state contact angle, which differs from the static contact angle. Based on the experimental results of LOX interface at different wall overheat conditions, the relationship between wall superheat and the steady-state contact angle applicable to cryogenic propellants is established. Due to the imperfect internal corner caused by industrial machining, the equilibrium height could only reach a finite value. The operation pressure has little effect on the equilibrium height. As the wall overheat and gravity level increase, the capillary rise equilibrium height decreases. Moreover, dimensionless correlations are developed to predict the capillary rise equilibrium height of LOX on the plate and in a corner. The present study is of significance for predicting the propellant interface height in reduced gravity conditions to design and construct propellant management devices.
- 1 April 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (4)
Experimental study on equilibrium height of capillary rise with liquid oxygen in reduced gravity under the influence of thermal leakage
Cryogenic propellants often experience reduced-gravity levels during orbital transfer and deep exploration, which leads to uncertainty in their interface structure and equilibrium height. In addition, unexpected thermal leakage can cause evaporation at the three-phase contact line, further complicating the prediction of the interface location. In this research, a cryogenic testing apparatus based on a magnetic compensation platform was developed to investigate the capillary rise equilibrium height on a plate and in the corner of liquid oxygen (LOX) in reduced gravity. A periscope-like visual system is employed to visualize and record the interface evolution in the magnetic compensation region. It is found that wall overheat leads to a decrease in the steady-state contact angle, which differs from the static contact angle. Based on the experimental results of LOX interface at different wall overheat conditions, the relationship between wall superheat and the steady-state contact angle applicable to cryogenic propellants is established. Due to the imperfect internal corner caused by industrial machining, the equilibrium height could only reach a finite value. The operation pressure has little effect on the equilibrium height. As the wall overheat and gravity level increase, the capillary rise equilibrium height decreases. Moreover, dimensionless correlations are developed to predict the capillary rise equilibrium height of LOX on the plate and in a corner. The present study is of significance for predicting the propellant interface height in reduced gravity conditions to design and construct propellant management devices.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Decoupling of the effects of inertial and transverse capillary forces on bubble breakthrough in porous structures
Porous media are extensively employed in gas–liquid separation processes due to their remarkable capillary effects arising from the pores at the micro/nanoscale. However, the coupling between inertial and transverse capillary forces and their respective influences on bubble breakthrough remain insufficiently understood. We designed porous structures with imposed transverse capillary pressures by adding transverse pores to rectangular channels and used an equivalent transverse pressure method to experimentally quantify how transverse capillary forces influence bubble dynamics, the bubble point pressure, and the critical flow rate. The gas–liquid flow patterns were characterized using high-speed imaging and microscopic particle image velocimetry. Compared with pores without imposed transverse pressure, increasing the transverse capillary number to 0.71 for isopropanol and 0.97 for HFE7500, corresponding to an imposed transverse pressure of 600 Pa, leads to notable increases in the normalized bubble point pressure and critical flow rate for a main pore size of 100 μm, reaching 18.7% and 7.5% for isopropanol and 27.5% and 13.4% for HFE7500, respectively. This enhancement is governed by a synergistic competition mechanism. Transverse pore structures increase the bubble point pressure via contact-line pinning, whereas sufficiently large transverse pressure partially offsets the pinning effect and further strengthens interfacial wetting. These results elucidate the interplay between inertia and transverse capillarity in porous media and provide practical guidance for optimizing the design of capillary-wetted porous structures for efficient gas–liquid separation.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Decoupling of the effects of inertial and transverse capillary forces on bubble breakthrough in porous structures
Porous media are extensively employed in gas–liquid separation processes due to their remarkable capillary effects arising from the pores at the micro/nanoscale. However, the coupling between inertial and transverse capillary forces and their respective influences on bubble breakthrough remain insufficiently understood. We designed porous structures with imposed transverse capillary pressures by adding transverse pores to rectangular channels and used an equivalent transverse pressure method to experimentally quantify how transverse capillary forces influence bubble dynamics, the bubble point pressure, and the critical flow rate. The gas–liquid flow patterns were characterized using high-speed imaging and microscopic particle image velocimetry. Compared with pores without imposed transverse pressure, increasing the transverse capillary number to 0.71 for isopropanol and 0.97 for HFE7500, corresponding to an imposed transverse pressure of 600 Pa, leads to notable increases in the normalized bubble point pressure and critical flow rate for a main pore size of 100 μm, reaching 18.7% and 7.5% for isopropanol and 27.5% and 13.4% for HFE7500, respectively. This enhancement is governed by a synergistic competition mechanism. Transverse pore structures increase the bubble point pressure via contact-line pinning, whereas sufficiently large transverse pressure partially offsets the pinning effect and further strengthens interfacial wetting. These results elucidate the interplay between inertia and transverse capillarity in porous media and provide practical guidance for optimizing the design of capillary-wetted porous structures for efficient gas–liquid separation.
- 1 October 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 281
Nucleate boiling of liquid oxygen under a magnetically compensated reduced-gravity environment
- 1 October 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 281
Nucleate boiling of liquid oxygen under a magnetically compensated reduced-gravity environment
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Capillary-driven liquid transport in a multistage micropillar array
Liquid transport in porous media is governed by capillary pressure and permeability, which are influenced by pore size regionally. Additionally, there exists a trade-off between achieving high capillary pressure and maintaining high permeability. In this work, porous structures consisting of micropillar arrays of gradient pore sizes are designed to balance such a regional trade-off to enable enhanced capillary-driven liquid transport. A dimensionless analytical model describing the wicking dynamics is developed to optimize the pore distribution. The model determines the optimal pore configuration characterized by a negative structural gradient, which minimizes the global wicking time for a given length of the porous media. The optimization result shows that the liquid wicking time can be reduced by up to 25% in the gradient structure compared to a uniform structure of the same length. Experimental validation of the optimized configuration is performed by measuring the wicking dynamics of different liquids in the porous structures. The results show that two-stage and three-stage gradient structures reduce the wicking time by 13.4% and 18.1%, respectively, which agrees well with theoretical predictions. Furthermore, we demonstrate a pillar spacing of 200 μm with the optimal capillary performance parameter K/reff of 4.6 μm at a given side length–spacing ratio of 1.27. The proposed model provides a practical tool for designing and optimizing porous structures at the pore scale to achieve maximum capillary flow rates.
- 1 April 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (4)
Capillary-driven liquid transport in a multistage micropillar array
Liquid transport in porous media is governed by capillary pressure and permeability, which are influenced by pore size regionally. Additionally, there exists a trade-off between achieving high capillary pressure and maintaining high permeability. In this work, porous structures consisting of micropillar arrays of gradient pore sizes are designed to balance such a regional trade-off to enable enhanced capillary-driven liquid transport. A dimensionless analytical model describing the wicking dynamics is developed to optimize the pore distribution. The model determines the optimal pore configuration characterized by a negative structural gradient, which minimizes the global wicking time for a given length of the porous media. The optimization result shows that the liquid wicking time can be reduced by up to 25% in the gradient structure compared to a uniform structure of the same length. Experimental validation of the optimized configuration is performed by measuring the wicking dynamics of different liquids in the porous structures. The results show that two-stage and three-stage gradient structures reduce the wicking time by 13.4% and 18.1%, respectively, which agrees well with theoretical predictions. Furthermore, we demonstrate a pillar spacing of 200 μm with the optimal capillary performance parameter K/reff of 4.6 μm at a given side length–spacing ratio of 1.27. The proposed model provides a practical tool for designing and optimizing porous structures at the pore scale to achieve maximum capillary flow rates.
- 20 February 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 269
Numerical investigation on helium pressurization behavior of cryogenic propellant in microgravity
- 20 February 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 269
Numerical investigation on helium pressurization behavior of cryogenic propellant in microgravity
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Experimental study of bubble flow dynamics in an asymmetric hierarchical porous structure
Porous media have been widely used for liquid–gas separation, benefiting from the strong capillary force generated by micro/nanoscale pores. Understanding the flow characteristics at the pore scale is important for the design of porous structures. In this study, the flow mechanisms of an isolated bubble in an asymmetric hierarchical pore were investigated by high-speed flow visualization and microscopic particle image velocimetry (Micro-PIV). The influence of the hierarchical pore on the flow field in the liquid and the dynamics of bubble penetration was investigated using isopropyl alcohol as the test liquid and polydimethylsiloxane micromodels. The critical pressure for the bubble to break through the pore was determined. The results show that the presence of secondary microstructure can increase the critical bubble point pressure by 79.7%. Meanwhile, the attack angle of the microstructure affects the critical pressure differently by changing the pinning effect, the curvature of the bubble as well as the flow field. The results of this work could provide guidance for optimizing the design of porous media for efficient gas–liquid separation.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Experimental study of bubble flow dynamics in an asymmetric hierarchical porous structure
Porous media have been widely used for liquid–gas separation, benefiting from the strong capillary force generated by micro/nanoscale pores. Understanding the flow characteristics at the pore scale is important for the design of porous structures. In this study, the flow mechanisms of an isolated bubble in an asymmetric hierarchical pore were investigated by high-speed flow visualization and microscopic particle image velocimetry (Micro-PIV). The influence of the hierarchical pore on the flow field in the liquid and the dynamics of bubble penetration was investigated using isopropyl alcohol as the test liquid and polydimethylsiloxane micromodels. The critical pressure for the bubble to break through the pore was determined. The results show that the presence of secondary microstructure can increase the critical bubble point pressure by 79.7%. Meanwhile, the attack angle of the microstructure affects the critical pressure differently by changing the pinning effect, the curvature of the bubble as well as the flow field. The results of this work could provide guidance for optimizing the design of porous media for efficient gas–liquid separation.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Behaviors of microdroplets impinging on supercooled superhydrophobic microgrooves
Microdroplet impact icing is a common occurrence in high altitudes or cloud environments. There is a lack of in-depth understanding regarding the icing behaviors of microdroplets interacting with anti-icing microstructures. While the impact of microstructure pitch on delaying icing is extensively studied, the microstructure height, as a similarly technology-controllable structural parameter, has received comparatively little attention in research. This study investigates the impact dynamics of microdroplets on supercooled superhydrophobic microgrooves, utilizing the coupled level-set and volume of fluid and enthalpy-porosity technologies for precise simulation. The behaviors of microdroplets impact on supercooled surface manifest distinctive characteristics compared with ambient surface, particularly evident when We < 170 (βmax (maximum spreading diameter)/βMod (predicted spreading diameter) ∼ 0.8). Unlike flat surfaces, microgrooves have been shown to reduce βmax by 52%. Additionally, an increase in H/Do (ratio of microgroove height H and droplet diameter Do) leads to a diminishing trend in βmax, showing a reduction of 13%. The outcomes of microdroplet impact progress from complete bouncing, partial bouncing, bouncing with satellite droplet breakup, to deposition, sequentially as the We and surface supercooling degree escalate. Heightening the microstructure alters the transition point between partial bouncing and bouncing with breakup, thereby expanding the range of droplet bouncing (with thresholds being doubled). This effect is attributed to satellite droplet breakup, supported by simulation results suggesting that droplet breakup reduces interface curvature, thus facilitating bouncing. Moreover, microgroove structures have the potential to decrease the dimensionless contact time of droplets by 33% when comparing H/Do = 0.4 with H/Do = 0.1.
- 1 December 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (12)
Behaviors of microdroplets impinging on supercooled superhydrophobic microgrooves
Microdroplet impact icing is a common occurrence in high altitudes or cloud environments. There is a lack of in-depth understanding regarding the icing behaviors of microdroplets interacting with anti-icing microstructures. While the impact of microstructure pitch on delaying icing is extensively studied, the microstructure height, as a similarly technology-controllable structural parameter, has received comparatively little attention in research. This study investigates the impact dynamics of microdroplets on supercooled superhydrophobic microgrooves, utilizing the coupled level-set and volume of fluid and enthalpy-porosity technologies for precise simulation. The behaviors of microdroplets impact on supercooled surface manifest distinctive characteristics compared with ambient surface, particularly evident when We < 170 (βmax (maximum spreading diameter)/βMod (predicted spreading diameter) ∼ 0.8). Unlike flat surfaces, microgrooves have been shown to reduce βmax by 52%. Additionally, an increase in H/Do (ratio of microgroove height H and droplet diameter Do) leads to a diminishing trend in βmax, showing a reduction of 13%. The outcomes of microdroplet impact progress from complete bouncing, partial bouncing, bouncing with satellite droplet breakup, to deposition, sequentially as the We and surface supercooling degree escalate. Heightening the microstructure alters the transition point between partial bouncing and bouncing with breakup, thereby expanding the range of droplet bouncing (with thresholds being doubled). This effect is attributed to satellite droplet breakup, supported by simulation results suggesting that droplet breakup reduces interface curvature, thus facilitating bouncing. Moreover, microgroove structures have the potential to decrease the dimensionless contact time of droplets by 33% when comparing H/Do = 0.4 with H/Do = 0.1.