Kathleen Coleman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kathleen Coleman has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Susan Trolier-McKinstry
Pennsylvania State University
3 shared publications - Raul Bermejo
Department of Materials Science Montanuniversitaet Leoben Leoben Austria
2 shared publications Adam Edstrand
Sandia National Laboratories 4 , Albuquerque, New Mexico 87185, USA
1 shared publicationBaxter Moody
HexaTech, Inc. 8 , Morrisville, North Carolina 27560, USA
1 shared publicationBenjamin A. Griffin
Defense Advanced Research Projects Agency 3 , Arlington, Virginia 22203, USA
1 shared publication- Betul Akkopru-Akgun
Center for Dielectrics and Piezoelectrics, Materials Research Institute, The Pennsylvania State University 1 , University Park, Pennsylvania 16802, USA
1 shared publication
Latest Publications
- 23 July 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 130 (4) , 044501
Residual stress analysis of aluminum nitride piezoelectric micromachined ultrasonic transducers using Raman spectroscopy
In this study, the Raman biaxial stress coefficients KII and strain-free phonon frequencies ω0 have been determined for the E2 (low), E2 (high), and A1 (LO) phonon modes of aluminum nitride, AlN, using both experimental and theoretical approaches. The E2 (high) mode of AlN is recommended for the residual stress analysis of AlN due to its high sensitivity and the largest signal-to-noise ratio among the studied modes. The E2 (high) Raman biaxial stress coefficient of −3.8 cm−1/GPa and strain-free phonon frequency of 656.68 cm−1 were then applied to perform both macroscopic and microscopic stress mappings. For macroscopic stress evaluation, the spatial variation of residual stress was measured across an AlN-on-Si wafer prepared by sputter deposition. A cross-wafer variation in residual stress of ∼150 MPa was observed regardless of the average stress state of the film. Microscopic stress evaluation was performed on AlN piezoelectric micromachined ultrasonic transducers (pMUTs) with submicrometer spatial resolution. These measurements were used to assess the effect of device fabrication on residual stress distribution in an individual pMUT and the effect of residual stress on the resonance frequency. At ∼20 μm directly outside the outer edge of the pMUT electrode, a large lateral spatial variation in residual stress of ∼100 MPa was measured, highlighting the impact of metallization structures on residual stress in the AlN film.
- 23 July 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 130 (4) , 044501
Residual stress analysis of aluminum nitride piezoelectric micromachined ultrasonic transducers using Raman spectroscopy
In this study, the Raman biaxial stress coefficients KII and strain-free phonon frequencies ω0 have been determined for the E2 (low), E2 (high), and A1 (LO) phonon modes of aluminum nitride, AlN, using both experimental and theoretical approaches. The E2 (high) mode of AlN is recommended for the residual stress analysis of AlN due to its high sensitivity and the largest signal-to-noise ratio among the studied modes. The E2 (high) Raman biaxial stress coefficient of −3.8 cm−1/GPa and strain-free phonon frequency of 656.68 cm−1 were then applied to perform both macroscopic and microscopic stress mappings. For macroscopic stress evaluation, the spatial variation of residual stress was measured across an AlN-on-Si wafer prepared by sputter deposition. A cross-wafer variation in residual stress of ∼150 MPa was observed regardless of the average stress state of the film. Microscopic stress evaluation was performed on AlN piezoelectric micromachined ultrasonic transducers (pMUTs) with submicrometer spatial resolution. These measurements were used to assess the effect of device fabrication on residual stress distribution in an individual pMUT and the effect of residual stress on the resonance frequency. At ∼20 μm directly outside the outer edge of the pMUT electrode, a large lateral spatial variation in residual stress of ∼100 MPa was measured, highlighting the impact of metallization structures on residual stress in the AlN film.
- 1 April 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (4) , 2465-2471
Mechanical failure dependence on the electrical history of lead zirconate titanate thin films
- 1 April 2021
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 41 (4) , 2465-2471
Mechanical failure dependence on the electrical history of lead zirconate titanate thin films
- 16 September 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (11) , 114102
Extrinsic contributions to the dielectric and pyroelectric properties of Pb0.99[(Zr0.52Ti0.48)0.98Nb0.02]O3 thin films on Si and Ni substrates
The character of extrinsic contributions to the dielectric and pyroelectric properties of Pb0.99[(Zr0.52Ti0.48)0.98Nb0.02]O3 (PZT) films on Ni foil and Si wafers was explored using Rayleigh analysis, third harmonic phase angle, and Preisach analysis from 15 K to 296 K. The temperature dependence of the domain structure, domain wall mobility, and domain switching influenced the intrinsic, extrinsic, and secondary contributions to the pyroelectric coefficients. This, in turn, produced markedly different room temperature pyroelectric coefficients of ∼250 μC/m2 K and ∼100 μC/m2 K, respectively, for films on Ni and Si. At room temperature, the dielectric irreversible Rayleigh parameter αray was 15.5 ± 0.1 and 28.4 ± 1.6 cm/kV for PZT on Si and Ni, respectively. The higher αray value for the Ni sample suggests more domain wall motion at room temperature, which was attributed to the lower stiffness on the Ni foil compared to the ∼500 μm thick Si substrate. Below 200 K, αray for the PZT Si sample exceeds that of the Ni/PZT sample. This is believed to arise from differences in the energy landscape of pinning centers for the domain wall motion. It is proposed that the residual stresses not only set the preferred domain structures but also the barrier heights for domain wall motion and domain switching.
- 16 September 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (11) , 114102
Extrinsic contributions to the dielectric and pyroelectric properties of Pb0.99[(Zr0.52Ti0.48)0.98Nb0.02]O3 thin films on Si and Ni substrates
The character of extrinsic contributions to the dielectric and pyroelectric properties of Pb0.99[(Zr0.52Ti0.48)0.98Nb0.02]O3 (PZT) films on Ni foil and Si wafers was explored using Rayleigh analysis, third harmonic phase angle, and Preisach analysis from 15 K to 296 K. The temperature dependence of the domain structure, domain wall mobility, and domain switching influenced the intrinsic, extrinsic, and secondary contributions to the pyroelectric coefficients. This, in turn, produced markedly different room temperature pyroelectric coefficients of ∼250 μC/m2 K and ∼100 μC/m2 K, respectively, for films on Ni and Si. At room temperature, the dielectric irreversible Rayleigh parameter αray was 15.5 ± 0.1 and 28.4 ± 1.6 cm/kV for PZT on Si and Ni, respectively. The higher αray value for the Ni sample suggests more domain wall motion at room temperature, which was attributed to the lower stiffness on the Ni foil compared to the ∼500 μm thick Si substrate. Below 200 K, αray for the PZT Si sample exceeds that of the Ni/PZT sample. This is believed to arise from differences in the energy landscape of pinning centers for the domain wall motion. It is proposed that the residual stresses not only set the preferred domain structures but also the barrier heights for domain wall motion and domain switching.
- Open Access
- 23 June 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (24) , 244101
Electrochemically driven degradation of chemical solution deposited ferroelectric thin-films in humid ambient
The ambient humidity significantly accelerates the degradation of lead zirconate titanate (PZT) films in microelectromechanical systems; the cause of such degradation is under debate. Here, it is shown that the degradation of chemical solution derived PZT thin-films in humid conditions is driven by the system's electrochemical activity toward water electrolysis. The layer stacks with Pt-based electrodes exhibited a faster degradation rate owing to their higher electrocatalytic activity compared to Au. A degradation model is proposed based on the electrolysis of liquid or gaseous H2O, involving the evolution of oxygen and hydrogen gas at the top and bottom electrodes. Degradation proceeds above the threshold voltage for a given electrode system and is driven by the evolution and pressure build-up of gaseous species at the PZT/electrode interfaces. The pressure build-up causes film cracking, delamination of the film and electrodes, electrothermal breakdown events, and eventually time-dependent dielectric breakdown. Significantly larger post-breakdown crater sizes in humid than in dry conditions suggests that larger cracks through which dielectric breakdown through humidified air can occur. Overall, these effects are shown to cause sample failure up to six orders of magnitude of time earlier than for operation in dry conditions. Thus, in order to improve the resilience of thin-film systems in humid conditions, it is imperative to protect the electrochemically active electrode components of the device.
- 23 June 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 127 (24) , 244101
Open AccessElectrochemically driven degradation of chemical solution deposited ferroelectric thin-films in humid ambient
The ambient humidity significantly accelerates the degradation of lead zirconate titanate (PZT) films in microelectromechanical systems; the cause of such degradation is under debate. Here, it is shown that the degradation of chemical solution derived PZT thin-films in humid conditions is driven by the system's electrochemical activity toward water electrolysis. The layer stacks with Pt-based electrodes exhibited a faster degradation rate owing to their higher electrocatalytic activity compared to Au. A degradation model is proposed based on the electrolysis of liquid or gaseous H2O, involving the evolution of oxygen and hydrogen gas at the top and bottom electrodes. Degradation proceeds above the threshold voltage for a given electrode system and is driven by the evolution and pressure build-up of gaseous species at the PZT/electrode interfaces. The pressure build-up causes film cracking, delamination of the film and electrodes, electrothermal breakdown events, and eventually time-dependent dielectric breakdown. Significantly larger post-breakdown crater sizes in humid than in dry conditions suggests that larger cracks through which dielectric breakdown through humidified air can occur. Overall, these effects are shown to cause sample failure up to six orders of magnitude of time earlier than for operation in dry conditions. Thus, in order to improve the resilience of thin-film systems in humid conditions, it is imperative to protect the electrochemically active electrode components of the device.
- 1 June 2020
- Published by Elsevier in Acta Materialia
- Vol. 191, 245-252
Thickness Dependence of crack initiation and propagation in stacks for piezoelectric microelectromechanical systems
- 1 June 2020
- Published by Elsevier in Acta Materialia
- Vol. 191, 245-252
Thickness Dependence of crack initiation and propagation in stacks for piezoelectric microelectromechanical systems