SSShohei Suzuki

Shohei Suzuki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shohei Suzuki has a total of 9 co-authors. Here are the top co-authors by number of shared publications:

  • Kazuhiko Ueda

    Department of Crown and Bridge Prosthodontics, The Nippon Dental University School of Life Dentistry at Niigata, Niigata, Japan

    3 shared publications
  • Fumihiko Watanabe

    Department of Crown and Bridge Prosthodontics, School of Life Dentistry at Niigata, The Nippon Dental University, Niigata, Japan

    2 shared publications
  • Jan-Frederik Güth

    Department of Prosthetic Dentistry, University Hospital, LMU Munich, Munich, Germany

    1 shared publication
  • Kazuhiko Hiroyasu

    Oral Implant Care Unit, Niigata Hospital, The Nippon Dental University, Tokyo, Japan

    1 shared publication
  • Kurt Erdelt

    Department of Prosthetic Dentistry, University Hospital, LMU Munich, Munich, Germany

    1 shared publication
  • Munetsugu Seto

    Department of Crown and Bridge Prosthodontics, The Nippon Dental University School of Life Dentistry at Niigata, Niigata, Japan

    1 shared publication

Latest Publications

  • Dimensional changes over time in stereolithographic models fabricated with a 3D printer

    by Shohei Suzuki, Rina Suzuki, Munetsugu Seto, Kazuhiko Hiroyasu, Shin Ogura, Kazuhiko Ueda

    This study aimed to ascertain the effects of the shape of stereolithographic models fabricated with a three-dimensional (3D) printer and the use of different types of liquid resin on the dimensional changes of these models over time, to obtain valuable information for determining the period for which such models can be used following fabrication. Stereolithography models with the shape of a large truncated cone or a small truncated cone were fabricated using liquid resin as surgical guides (Group G) or master casts (Group M). (four groups in total, each n = 11). The shapes of all experimental specimens were measured immediately after fabrication and 1 day, 1 week, 2 weeks, 3 weeks, 4 weeks, 2 months, 3 months, 6 months, 1 year, and 1.5 years later. The shape data collected immediately after fabrication were taken as baseline data, and the dimensional changes over time at each timepoint were calculated. No significant change from 1 day to 1 year after fabrication was observed in any of the groups, but the change after 1.5 years was significantly larger than the changes at the other timepoints (p < 0.001). Significantly larger changes were evident in Group M than in Group G at all timepoints (p < 0.001). These results suggested that, from the viewpoint of dimensional stability over time, stereolithographic models should be used within 1 year of fabrication, and that the type of liquid resin used for stereolithographic model fabrication may affect how its dimensions change over time.


  • Effects of porcelain veneering methods on conformity of the marginal and internal fit of three-unit zirconia framework

    by Shohei Suzuki, Kazuhiko Ueda, Kurt Erdelt, Fumihiko Watanabe, Jan-Frederik Güth

    The purpose of this study is to investigate the effects of porcelain veneering methods on the marginal and internal fit of a three-unit zirconia framework. A zirconia master model, in which the lower-left second premolar and the second left molar were used as the abutment, was obtained using an intraoral scanner. Based on the data, three-unit zirconia frameworks for fabricating all-ceramic bridges were designed and milled (FW group). Two types of all-ceramic bridge were fabricated by veneering porcelain onto these frameworks using the press-over technique (P group) and the layering technique (L group). The replica technique was used to measure the gap size between the abutments and the bridges. Measurements were taken in the marginal opening area (MO), chamfer area (CH), axial area (AX), and occlusal area (OC). Statistical analysis was performed using the Mann–Whitney U-test. There was no significant difference in MO and CH between the P and L groups. However, in AX, the L group had a significantly larger gap size than that of the P group (p = 0.003). In addition, compared with the FW group, the P group showed a significantly larger gap size in MO (p < 0.000), CH (p = 0.008), and OC (p < 0.000). These results indicate that the gap size increased after porcelain veneering using the press-over and layering techniques. In addition, the all-ceramic bridges fabricated using the press-over and layering techniques had approximately equal gap sizes in MO.


  • Marginal and internal fit of three-unit zirconia fixed dental prostheses: Effects of prosthesis design, cement space, and zirconia type

    by Shohei Suzuki, Yasuhiro Katsuta, Kazuhiko Ueda, Fumihiko Watanabe

    The purpose of this study was to compare the marginal and internal fit of three-unit fixed dental prostheses (FDPs) fabricated using CAD/CAM with two designs, two cement space (CS), and two zirconia types. A master model with two zirconia abutments and a missing tooth was scanned with an intraoral scanner. FDPs were fabricated with two designs (Full contour: FC, Framework: FW), two zirconia types (multi-layer: L, single-layer: W), and two CS values (30 and 45 μm for L and 30 μm for W). There were six experimental groups. The fit of the FDPs was evaluated using the replica method. The space between an abutment and the FDPs in the marginal (MO), chamfer (CH), axial (AX), and occlusal (OC) areas was measured under an optical microscope and the data was statistically analyzed using three-way ANOVA and Bonferroni test (p < 0.05). FW-l-45 μm showed a significantly smaller space than those for the FC in MO (p = 0.011), CH (p = 0.001) and AXE (p = 0.003). FW-l-30 μm showed a significantly smaller space than that for the 45 µm in AXE (p = 0.000) and OC (p = 0.016). FW-W-30 µm showed a significantly smaller space than that for the L in MO (p = 0.000), CH (p = 0.000), AXE (p = 0.000), and OC (p = 0.002). The design and CS of the FDPs affected the fit. FDPs with single-layer zirconia showed better fit than that obtained with multi-layer zirconia.