Yutian Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yutian Sun has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Jichao Han
Harbin University of Science and Technology
5 shared publications - Baojun Ge
Harbin University of Science and Technology, Harbin, China
4 shared publications - Dong Jiechen
Harbin University of Science and Technology, Harbin 150080, China
2 shared publications - Li Weili
Harbin University of Science and Technology, Harbin, China
2 shared publications - Liu Yufei
Harbin University of Science and Technology, Harbin 150080, China
2 shared publications - Zheng Ping
Harbin Institute of Technology, Harbin, China
2 shared publications
Latest Publications
- Open Access
- 13 February 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (2) , 243
Cooperative Control Strategy for Low-Voltage Ride-Through of DFIGM Based on an Improved IGBT-Based Active Crowbar
To address the low-voltage fault issue in doubly fed induction generator-motor (DFIGM) systems, this paper proposes a practically implementable cooperative control strategy that integrates an improved current reversely tracking control (CRTC) scheme with an enhanced IGBT-based active crowbar topology. The proposed method optimizes the current-tracking coefficients under rotor voltage and current constraints during LVRT operation. Meanwhile, the enhanced active crowbar provides reactive power support, thereby suppressing negative-sequence current components, mitigating harmonic distortion, and improving the power quality at the point of common coupling (PCC). A 10-MW DFIGM model is developed, and comparative studies are conducted with the conventional inductance emulating control (IEC) and the crowbar structure. The experimental results show the feasibility and effectiveness of the proposed method.
- 13 February 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (2) , 243
Open AccessCooperative Control Strategy for Low-Voltage Ride-Through of DFIGM Based on an Improved IGBT-Based Active Crowbar
To address the low-voltage fault issue in doubly fed induction generator-motor (DFIGM) systems, this paper proposes a practically implementable cooperative control strategy that integrates an improved current reversely tracking control (CRTC) scheme with an enhanced IGBT-based active crowbar topology. The proposed method optimizes the current-tracking coefficients under rotor voltage and current constraints during LVRT operation. Meanwhile, the enhanced active crowbar provides reactive power support, thereby suppressing negative-sequence current components, mitigating harmonic distortion, and improving the power quality at the point of common coupling (PCC). A 10-MW DFIGM model is developed, and comparative studies are conducted with the conventional inductance emulating control (IEC) and the crowbar structure. The experimental results show the feasibility and effectiveness of the proposed method.
- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 41 (2) , 1527-1539
Influence of End Structure Optimization on 3D Electromagnetic Field and Losses of a Novel Double-Side Counter-Flow Turbogenerator
Turbogenerators are crucial equipment in power generation. Unreasonable design of the end of such generators can lead increased end losses that can impact the safety and stability of the system in operation. In this study, a 350-MW novel double-side counter-flow large turbogenerator is proposed. A three-dimensional transient nonlinear electromagnetic field model of the end region of the turbogenerator is established to analyze the electromagnetic field. In order to reduce the losses of end components, the novel structural optimization design is proposed. The influence of the modified end structure on the flux density of the end components is investigated by varying the relative lengths of the stator and rotor cores and the distances between the copper screen and windings. The losses of the end components are obtained under different end structures. The results show that a reasonable relative length between the stator and rotor cores and distance between the copper screen and winding effectively reduced losses from end components in the proposed design. The results of the calculation are verified experimentally. Thus, this study provides an important reference for the optimization of the end structures of turbogenerators.
- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 41 (2) , 1527-1539
Influence of End Structure Optimization on 3D Electromagnetic Field and Losses of a Novel Double-Side Counter-Flow Turbogenerator
Turbogenerators are crucial equipment in power generation. Unreasonable design of the end of such generators can lead increased end losses that can impact the safety and stability of the system in operation. In this study, a 350-MW novel double-side counter-flow large turbogenerator is proposed. A three-dimensional transient nonlinear electromagnetic field model of the end region of the turbogenerator is established to analyze the electromagnetic field. In order to reduce the losses of end components, the novel structural optimization design is proposed. The influence of the modified end structure on the flux density of the end components is investigated by varying the relative lengths of the stator and rotor cores and the distances between the copper screen and windings. The losses of the end components are obtained under different end structures. The results show that a reasonable relative length between the stator and rotor cores and distance between the copper screen and winding effectively reduced losses from end components in the proposed design. The results of the calculation are verified experimentally. Thus, this study provides an important reference for the optimization of the end structures of turbogenerators.
- 29 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (1) , 772-781
Design and Analysis of the High Torque Density Circumferentially Excited Permanent Magnet Motor Based on PSO
In order to further improve the torque density of the permanent magnet motor, a novel 650 kW circumferentially excited permanent magnet (CEPM) motor is proposed and designed. The response surface method and particle swarm optimization (PSO) algorithm are used to obtain the optimal design of the circumferentially excited permanent magnet motor. The electromagnetic performance is analyzed under the different operating conditions. The mathematical model of three-dimensional end transient electromagnetic filed is calculated to obtain the end leakage magnetic flux and end component losses, which provides the heat source for thermal analysis. Novel air-water cooling dual self-circulation ventilation system with the axial-flow fan is proposed. The complex fluid flow and the temperature distribution of each component are determined in the circumferentially excited permanent magnet motor based on three-dimensional fluid-solid thermal coupled model. The highest temperature of the components is determined. This novel ventilation cooling system can effectively take away the heat in the circumferentially excited permanent magnet motor. A prototype of circumferentially excited permanent magnet motor is manufactured. The designs and analyses are validated.
- 29 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 39 (1) , 772-781
Design and Analysis of the High Torque Density Circumferentially Excited Permanent Magnet Motor Based on PSO
In order to further improve the torque density of the permanent magnet motor, a novel 650 kW circumferentially excited permanent magnet (CEPM) motor is proposed and designed. The response surface method and particle swarm optimization (PSO) algorithm are used to obtain the optimal design of the circumferentially excited permanent magnet motor. The electromagnetic performance is analyzed under the different operating conditions. The mathematical model of three-dimensional end transient electromagnetic filed is calculated to obtain the end leakage magnetic flux and end component losses, which provides the heat source for thermal analysis. Novel air-water cooling dual self-circulation ventilation system with the axial-flow fan is proposed. The complex fluid flow and the temperature distribution of each component are determined in the circumferentially excited permanent magnet motor based on three-dimensional fluid-solid thermal coupled model. The highest temperature of the components is determined. This novel ventilation cooling system can effectively take away the heat in the circumferentially excited permanent magnet motor. A prototype of circumferentially excited permanent magnet motor is manufactured. The designs and analyses are validated.
- 31 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (12) , 12082-12092
Design and Analysis of Complex End Region of Pumped Storage Generator Motor Based on Novel Electromagnetic Vector Method
A very large end leakage flux is produced by the end winding of a pumped storage generator motor. It has a significant impact on the design, flux density, and temperature in the end region of the pumped storage generator motor. The high temperature makes it difficult to design pumped storage generator motors. To quickly and accurately obtain the flux density of end components, a novel electromagnetic vector method is proposed in this article. A 300-MW pumped storage generator motor is designed. The electromagnetic vector method and finite element method are used to calculate the flux density of the end components, respectively. The obtained results are compared and analyzed. The results reveal that the novel method is more convenient and faster than the finite element method. The novel electromagnetic vector method reduces the design time and calculation time of the end flux density. The flux density and losses of the end components in the pumped storage generator motor are studied under different operating conditions. Three-dimensional fluid and thermal coupled field is calculated and analyzed. Moreover, the calculation results are verified by the experimental values.
- 31 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (12) , 12082-12092
Design and Analysis of Complex End Region of Pumped Storage Generator Motor Based on Novel Electromagnetic Vector Method
A very large end leakage flux is produced by the end winding of a pumped storage generator motor. It has a significant impact on the design, flux density, and temperature in the end region of the pumped storage generator motor. The high temperature makes it difficult to design pumped storage generator motors. To quickly and accurately obtain the flux density of end components, a novel electromagnetic vector method is proposed in this article. A 300-MW pumped storage generator motor is designed. The electromagnetic vector method and finite element method are used to calculate the flux density of the end components, respectively. The obtained results are compared and analyzed. The results reveal that the novel method is more convenient and faster than the finite element method. The novel electromagnetic vector method reduces the design time and calculation time of the end flux density. The flux density and losses of the end components in the pumped storage generator motor are studied under different operating conditions. Three-dimensional fluid and thermal coupled field is calculated and analyzed. Moreover, the calculation results are verified by the experimental values.
- Open Access
- 30 August 2022
- Published by Boya Century Publishing in BCP Business & Management
- Vol. 25, 438-442
Analysis of Key Drivers and Forecast for the Singapore Dollar
This paper analyzes the key drivers for the change of the Singapore dollar and makes predictions for its future trend. First, the author focuses on trade by discussing the GDP and current account of Singapore, mainly in terms of services. Second, the author focuses on inflation by discussing the current situation of inflation and Monetary Authority of Singapore’s monetary policy. In the end, the author forecasts that the exchange rate of the SGD against the CNY is expected to fluctuate in the short-time and strengthen in the long-time.
- 30 August 2022
- Published by Boya Century Publishing in BCP Business & Management
- Vol. 25, 438-442
Open AccessAnalysis of Key Drivers and Forecast for the Singapore Dollar
This paper analyzes the key drivers for the change of the Singapore dollar and makes predictions for its future trend. First, the author focuses on trade by discussing the GDP and current account of Singapore, mainly in terms of services. Second, the author focuses on inflation by discussing the current situation of inflation and Monetary Authority of Singapore’s monetary policy. In the end, the author forecasts that the exchange rate of the SGD against the CNY is expected to fluctuate in the short-time and strengthen in the long-time.
- Open Access
- 1 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 3252-3262
Influence of Complex Fluid Flow on Temperature Distribution in the Rotor Region of Large Hydrogenerator Under the Rotor Rotation
Ventilation cooling design is one of the key technologies during the design of large hydrogenerator. With the increase of hydrogenerator capacity, the overheating problem of rotor region become more and more serious. In this paper, a 250 MW hydrogenerator is analyzed. The transient electromagnetic field of the hydrogenerator is calculated. The losses (heat sources) of rotor components in the rotor region of the hydrogenerator are determined. Three-dimensional fluid and thermal coupled mathematic model of the hydrogenerator rotor region is established. The rotor rotation of the hydrogenerator is considered. The distribution of complex fluid velocity in the rotor region is calculated using the finite volume method. The influence of fluid velocity in the different directions on the temperature of the rotor excitation winding is studied under the different flow rates in the rotor region. The surface heat-transfer coefficient distribution of the rotor components is determined. The temperature distribution of the rotor excitation winding, rotor pole body, rotor press plate, rotor damping bar, and rotor end ring is obtained. The calculated temperature results match well with test values. These provide an important reference for the rotor structural design and optimization of larger hydrogenerator.
- 1 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 3252-3262
Open AccessInfluence of Complex Fluid Flow on Temperature Distribution in the Rotor Region of Large Hydrogenerator Under the Rotor Rotation
Ventilation cooling design is one of the key technologies during the design of large hydrogenerator. With the increase of hydrogenerator capacity, the overheating problem of rotor region become more and more serious. In this paper, a 250 MW hydrogenerator is analyzed. The transient electromagnetic field of the hydrogenerator is calculated. The losses (heat sources) of rotor components in the rotor region of the hydrogenerator are determined. Three-dimensional fluid and thermal coupled mathematic model of the hydrogenerator rotor region is established. The rotor rotation of the hydrogenerator is considered. The distribution of complex fluid velocity in the rotor region is calculated using the finite volume method. The influence of fluid velocity in the different directions on the temperature of the rotor excitation winding is studied under the different flow rates in the rotor region. The surface heat-transfer coefficient distribution of the rotor components is determined. The temperature distribution of the rotor excitation winding, rotor pole body, rotor press plate, rotor damping bar, and rotor end ring is obtained. The calculated temperature results match well with test values. These provide an important reference for the rotor structural design and optimization of larger hydrogenerator.
- Open Access
Prediction of Electromagnetic Characteristics in Stator End Parts of a Turbo-Generator Based on MLP and SVR
In order to study the multiple restricted factors and parameters of the eddy current loss of generator end structures, both the multi-layer perceptron (MLP) and support vector regression (SVR) are used to study and predict the mechanism of the synergistic effect of metal shield conductivity, relative permeability of clamping plates and structural characteristics of eddy current losses. Based on the eddy current losses of generator end structures under different metal shielding thicknesses and electromagnetic properties, the calculation accuracy of the MLP and SVR is compared. The prediction method gives an effective means for the complex design of the end region of the generator, which reduces the effort of the designers. It also promotes the design efficiency of the electrical generator.
Open AccessPrediction of Electromagnetic Characteristics in Stator End Parts of a Turbo-Generator Based on MLP and SVR
In order to study the multiple restricted factors and parameters of the eddy current loss of generator end structures, both the multi-layer perceptron (MLP) and support vector regression (SVR) are used to study and predict the mechanism of the synergistic effect of metal shield conductivity, relative permeability of clamping plates and structural characteristics of eddy current losses. Based on the eddy current losses of generator end structures under different metal shielding thicknesses and electromagnetic properties, the calculation accuracy of the MLP and SVR is compared. The prediction method gives an effective means for the complex design of the end region of the generator, which reduces the effort of the designers. It also promotes the design efficiency of the electrical generator.
- Open Access
- 19 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 120001-120009
Thermal Modeling and Experimental Validation in the Rotor Region of Hydrogenerator With Different Rotor Structures
Thermal management is often considered a bottleneck in the pursuit of the next generation hydrogenerator in the electric power system. Overheating of the complex rotor parts has become one of the main problems affecting safe and stable hydrogenerator operation. In this paper, a 250 MW hydrogenerator is analyzed. The transient electromagnetic field of the hydrogenerator is calculated and the losses of the rotor parts are obtained. The rotation of the hydrogenerator rotor is considered. Three-dimensional fluid and thermal mathematic and physical models of the hydrogenerator are established. The loss values from electromagnetic field calculations are applied to the rotor parts as heat sources in the temperature field. After solving the fluid and thermal equations of fluid-solid conjugated heat transfer, influence of the structures of rotor support plate, rotor pole body insulation, and rotor excitation winding on the fluid flow and temperature distribution in the rotor region of hydrogenerator is studied using the finite volume method. The calculated temperature result of rotor excitation winding is compared with the measured value. The calculated temperature result agrees well with the measured value. It provides an important reference for optimizing the rotor structure of the larger hydrogenerator.
- 19 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 120001-120009
Open AccessThermal Modeling and Experimental Validation in the Rotor Region of Hydrogenerator With Different Rotor Structures
Thermal management is often considered a bottleneck in the pursuit of the next generation hydrogenerator in the electric power system. Overheating of the complex rotor parts has become one of the main problems affecting safe and stable hydrogenerator operation. In this paper, a 250 MW hydrogenerator is analyzed. The transient electromagnetic field of the hydrogenerator is calculated and the losses of the rotor parts are obtained. The rotation of the hydrogenerator rotor is considered. Three-dimensional fluid and thermal mathematic and physical models of the hydrogenerator are established. The loss values from electromagnetic field calculations are applied to the rotor parts as heat sources in the temperature field. After solving the fluid and thermal equations of fluid-solid conjugated heat transfer, influence of the structures of rotor support plate, rotor pole body insulation, and rotor excitation winding on the fluid flow and temperature distribution in the rotor region of hydrogenerator is studied using the finite volume method. The calculated temperature result of rotor excitation winding is compared with the measured value. The calculated temperature result agrees well with the measured value. It provides an important reference for optimizing the rotor structure of the larger hydrogenerator.
- Open Access
- 26 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 70703-70712
Influence of Extension Length of Rotor End Windings on the Three-Dimensional Electromagnetic Field and Temperature Rise in the Large Turbine Generator End Zone With Magnetic Screen
Leakage magnetic field from the rotor end windings affects obviously the electromagnetic losses and temperature of end components in the turbine generator end zone with magnetic screen. As the capacity of turbine generator increases, this effect of rotor end windings has become more prominent. To investigate influence of the extension length of rotor end windings on the electromagnetic and thermal fields in the turbine generator end zone with magnetic screen, three-dimensional transient electromagnetic field model of 1250 MW turbine generator end zone is given. Leakage magnetic field and losses of end components are compared and studied in the end zone under the different extension lengths of rotor end windings. Based on the calculation results of electromagnetic losses (heat sources) and flow network (boundary conditions), three-dimensional fluid-thermal coupling field is calculated in the turbine generator end zone with magnetic screen. Distribution of complex fluid velocity in the end zone is obtained. Influence of the different extension lengths of rotor end windings on the stator-end copper coil, screen plate, finger plate, press plate, magnetic screen, and stator end core is researched in the turbine generator end zone. The accuracy of calculation results is validated by experimental values.
- 26 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 70703-70712
Open AccessInfluence of Extension Length of Rotor End Windings on the Three-Dimensional Electromagnetic Field and Temperature Rise in the Large Turbine Generator End Zone With Magnetic Screen
Leakage magnetic field from the rotor end windings affects obviously the electromagnetic losses and temperature of end components in the turbine generator end zone with magnetic screen. As the capacity of turbine generator increases, this effect of rotor end windings has become more prominent. To investigate influence of the extension length of rotor end windings on the electromagnetic and thermal fields in the turbine generator end zone with magnetic screen, three-dimensional transient electromagnetic field model of 1250 MW turbine generator end zone is given. Leakage magnetic field and losses of end components are compared and studied in the end zone under the different extension lengths of rotor end windings. Based on the calculation results of electromagnetic losses (heat sources) and flow network (boundary conditions), three-dimensional fluid-thermal coupling field is calculated in the turbine generator end zone with magnetic screen. Distribution of complex fluid velocity in the end zone is obtained. Influence of the different extension lengths of rotor end windings on the stator-end copper coil, screen plate, finger plate, press plate, magnetic screen, and stator end core is researched in the turbine generator end zone. The accuracy of calculation results is validated by experimental values.
- Open Access
Magnetic Field Characteristics and Stator Core Losses of High-Speed Permanent Magnet Synchronous Motors
This study focuses on the core losses in the stator region of high-speed permanent magnet synchronous motors, magnetic field characteristics in the load region, and variations in iron losses caused by changes in these areas. A two-pole 120 kW high-speed permanent magnet synchronous motor is used as the object of study, and a two-dimensional transient electromagnetic field-variable load circuit combined calculation model is established. Based on electromagnetic field theory, the electromagnetic field of the high-speed permanent magnet synchronous motor under multi-load conditions is calculated using the time-stepping finite element method. The magnetic field distribution of the high-speed permanent magnet synchronous motor under a multi-load condition is obtained, and the variations in iron core losses in different parts of the motor under multi-load conditions are further analyzed. The calculation results show that most of the stator iron core losses are dissipated in the stator yoke. The stator yoke iron loss under the no-load condition exceeds 70% of the total stator iron core loss. The stator yoke iron loss under rated operation conditions exceeds 50% of the total stator iron core loss. The stator loss under rated load operation conditions is higher than that under no-load operation. These observations are sufficient to demonstrate that the running status of high-speed motors is closely related to the stator iron losses, which have significance in determining the reasonable yoke structure of high-speed and high-power motors and the cooling methods of motor stators.
Open AccessMagnetic Field Characteristics and Stator Core Losses of High-Speed Permanent Magnet Synchronous Motors
This study focuses on the core losses in the stator region of high-speed permanent magnet synchronous motors, magnetic field characteristics in the load region, and variations in iron losses caused by changes in these areas. A two-pole 120 kW high-speed permanent magnet synchronous motor is used as the object of study, and a two-dimensional transient electromagnetic field-variable load circuit combined calculation model is established. Based on electromagnetic field theory, the electromagnetic field of the high-speed permanent magnet synchronous motor under multi-load conditions is calculated using the time-stepping finite element method. The magnetic field distribution of the high-speed permanent magnet synchronous motor under a multi-load condition is obtained, and the variations in iron core losses in different parts of the motor under multi-load conditions are further analyzed. The calculation results show that most of the stator iron core losses are dissipated in the stator yoke. The stator yoke iron loss under the no-load condition exceeds 70% of the total stator iron core loss. The stator yoke iron loss under rated operation conditions exceeds 50% of the total stator iron core loss. The stator loss under rated load operation conditions is higher than that under no-load operation. These observations are sufficient to demonstrate that the running status of high-speed motors is closely related to the stator iron losses, which have significance in determining the reasonable yoke structure of high-speed and high-power motors and the cooling methods of motor stators.