Arsalan Razzaq
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arsalan Razzaq has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Stefaan De Wolf
King Abdullah University of Science and Technology (KAUST)
13 shared publications - Caner Deger
Department of Physics, Marmara University, Istanbul, Turkey
6 shared publications - Erkan Aydin
Department of Chemistry and Center for NanoScience (CeNS) Ludwig‐Maximilians‐Universität (LMU) Munich Germany
6 shared publications - Ilhan Yavuz
Department of Physics, Marmara University, Istanbul, Turkey
6 shared publications Badri Vishal
Center for Renewable Energy and Storage Technologies (CREST) Physical Sciences and Engineering Division (PSE) King Abdullah University of Science and Technology (KAUST) Thuwal Saudi Arabia
5 shared publications- Lujia Xu
KAUST Solar Center, Physical Sciences and Engineering Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900, Kingdom of Saudi Arabia
5 shared publications
Latest Publications
- 29 October 2026
- Published by Springer Nature in Nature Energy
- p. 1-12
Perovskite lattice compliance enables efficient and stable bifacial perovskite/silicon tandem photovoltaics
- 29 October 2026
- Published by Springer Nature in Nature Energy
- p. 1-12
Perovskite lattice compliance enables efficient and stable bifacial perovskite/silicon tandem photovoltaics
- Open Access
- 11 July 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (63) , e77018
Stabilizing Buried Contacts in Hybrid‐Deposited Perovskite Solar Cells via Amidinium‐Based Passivation
Monolithic integration of perovskite solar cells (PSCs) with textured silicon is essential for commercializing perovskite/silicon tandem photovoltaics. Hybrid evaporation–solution processing enables conformal perovskite deposition on textured surfaces, but residual PbI 2 at the buried interface limits performance and stability. Here, we introduce 2,4‐difluorobenzamidine hydrochloride (2,4‐FPhFACl) into self‐assembled monolayers (SAMs) as a buried hole‐selective contact to improve interface quality. The amidinium groups strongly interact with the perovskite, suppressing thermal decomposition and eliminating PbI 2 formation. This approach enhances surface passivation and energy‐level alignment. Wide‐bandgap (1.65 eV) devices achieve a power conversion efficiency (PCE) of 20.19% and retain 80% efficiency after 2000 h at 85°C. Applied to fully textured perovskite/silicon tandems, this strategy delivers a champion PCE of 29.91% (1.04 cm 2 ), offering a scalable route to high‐performance tandem photovoltaics.
- 11 July 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (63) , e77018
Open AccessStabilizing Buried Contacts in Hybrid‐Deposited Perovskite Solar Cells via Amidinium‐Based Passivation
Monolithic integration of perovskite solar cells (PSCs) with textured silicon is essential for commercializing perovskite/silicon tandem photovoltaics. Hybrid evaporation–solution processing enables conformal perovskite deposition on textured surfaces, but residual PbI 2 at the buried interface limits performance and stability. Here, we introduce 2,4‐difluorobenzamidine hydrochloride (2,4‐FPhFACl) into self‐assembled monolayers (SAMs) as a buried hole‐selective contact to improve interface quality. The amidinium groups strongly interact with the perovskite, suppressing thermal decomposition and eliminating PbI 2 formation. This approach enhances surface passivation and energy‐level alignment. Wide‐bandgap (1.65 eV) devices achieve a power conversion efficiency (PCE) of 20.19% and retain 80% efficiency after 2000 h at 85°C. Applied to fully textured perovskite/silicon tandems, this strategy delivers a champion PCE of 29.91% (1.04 cm 2 ), offering a scalable route to high‐performance tandem photovoltaics.
- Open Access
- 12 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (25) , 35404-35414
Sequential Evaporation for Scalable Hybrid Processing of Perovskite/Silicon Tandem Solar Cells
The conformal coating of perovskites on textured silicon for tandem solar cells requires scalable deposition methods, for which hybrid vacuum-solution processing, using an evaporated inorganic scaffold (Pb/Cs halides) followed by solution conversion, is promising. Yet multisource coevaporation of the scaffold, as commonly used for lab-scale devices, is complex and costly to implement at an industrial scale. Here, we investigate sequential single-source evaporation of the inorganic scaffold as an industrially viable alternative. Five sequentially evaporated scaffold stacks were compared to a coevaporated reference. Despite differences in PbI2 conversion, halide distribution, and morphology, all showed similar single-junction device power conversion efficiencies (∼19%). The best scaffold (a PbI2/CsBr/PbI2/CsBr/PbI2 stack) achieved 28.4% in perovskite/silicon tandems without molecular additives, matching the coevaporated reference (28.3%). This work demonstrates that sequential deposition of the inorganic scaffold offers a scalable route to high-efficiency tandems.
- 12 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (25) , 35404-35414
Open AccessSequential Evaporation for Scalable Hybrid Processing of Perovskite/Silicon Tandem Solar Cells
The conformal coating of perovskites on textured silicon for tandem solar cells requires scalable deposition methods, for which hybrid vacuum-solution processing, using an evaporated inorganic scaffold (Pb/Cs halides) followed by solution conversion, is promising. Yet multisource coevaporation of the scaffold, as commonly used for lab-scale devices, is complex and costly to implement at an industrial scale. Here, we investigate sequential single-source evaporation of the inorganic scaffold as an industrially viable alternative. Five sequentially evaporated scaffold stacks were compared to a coevaporated reference. Despite differences in PbI2 conversion, halide distribution, and morphology, all showed similar single-junction device power conversion efficiencies (∼19%). The best scaffold (a PbI2/CsBr/PbI2/CsBr/PbI2 stack) achieved 28.4% in perovskite/silicon tandems without molecular additives, matching the coevaporated reference (28.3%). This work demonstrates that sequential deposition of the inorganic scaffold offers a scalable route to high-efficiency tandems.
- 23 September 2025
- Published by Springer Nature in Nature Materials
- Vol. 25 (2) , 259-266
Stabilized perovskite phases enabling efficient perovskite/perovskite/silicon triple-junction solar cells
Perovskite/perovskite/silicon triple-junction solar cells offer notable potential for high power output at low cost, yet their development is hindered by the phase instability of perovskites, which limits both device reproducibility and performance. The ~1.50-eV formamidinium lead triiodide (FAPbI3)-based middle layer degrades during subsequent fabrication steps, and the ~2.0-eV bromide-rich top layer suffers from light-induced phase segregation. Here we address these challenges by introducing ammonium propionic acid to enhance the phase stability in both perovskite layers. This strategy raises the phase transition energy barrier and suppresses vacancy defect formation through additional bonding with lattice cations. These improvements mitigate phase instabilities and enhance the power conversion efficiency of devices based on the modified perovskite films. As a result, perovskite/perovskite/silicon triple-junction solar cells achieve a power conversion efficiency of 28.7% on a 1-cm2 aperture area, with substantially improved reproducibility.
- 23 September 2025
- Published by Springer Nature in Nature Materials
- Vol. 25 (2) , 259-266
Stabilized perovskite phases enabling efficient perovskite/perovskite/silicon triple-junction solar cells
Perovskite/perovskite/silicon triple-junction solar cells offer notable potential for high power output at low cost, yet their development is hindered by the phase instability of perovskites, which limits both device reproducibility and performance. The ~1.50-eV formamidinium lead triiodide (FAPbI3)-based middle layer degrades during subsequent fabrication steps, and the ~2.0-eV bromide-rich top layer suffers from light-induced phase segregation. Here we address these challenges by introducing ammonium propionic acid to enhance the phase stability in both perovskite layers. This strategy raises the phase transition energy barrier and suppresses vacancy defect formation through additional bonding with lattice cations. These improvements mitigate phase instabilities and enhance the power conversion efficiency of devices based on the modified perovskite films. As a result, perovskite/perovskite/silicon triple-junction solar cells achieve a power conversion efficiency of 28.7% on a 1-cm2 aperture area, with substantially improved reproducibility.
- 9 December 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 10 (1) , 30-33
Improved Crystallinity and Efficiency in Perovskite Solar Cells through Layered Hybrid Deposition
- 9 December 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 10 (1) , 30-33
Improved Crystallinity and Efficiency in Perovskite Solar Cells through Layered Hybrid Deposition
- 30 October 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 9 (11) , 5635-5638
Practical Fill Factor Limits for Perovskite Solar Cells
- 30 October 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 9 (11) , 5635-5638
Practical Fill Factor Limits for Perovskite Solar Cells
- 30 August 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 9 (9) , 4633-4644
Mitigating Buried-Interface Energy Losses through Multifunctional Ligands in n–i–p Perovskite/Silicon Tandem Solar Cells
- 30 August 2024
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 9 (9) , 4633-4644
Mitigating Buried-Interface Energy Losses through Multifunctional Ligands in n–i–p Perovskite/Silicon Tandem Solar Cells
- Top Cited Papers
- 2 August 2024
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 385 (6708) , 533-538
Enhanced cation interaction in perovskites for efficient tandem solar cells with silicon
To achieve the full potential of monolithic perovskite/silicon tandem solar cells, crystal defects and film inhomogeneities in the perovskite top cell must be minimized. We discuss the use of methylenediammonium dichloride as an additive to the perovskite precursor solution, resulting in the incorporation of in situ–formed tetrahydrotriazinium (THTZ-H + ) into the perovskite lattice upon film crystallization. The cyclic nature of the THTZ-H + cation enables a strong interaction with the lead octahedra of the perovskite lattice through the formation of hydrogen bonds with iodide in multiple directions. This structure improves the device power conversion efficiency (PCE) and phase stability of 1.68 electron volts perovskites under prolonged light and heat exposure under 1-sun illumination at 85°C. Monolithic perovskite/silicon tandems incorporating THTZ-H + in the perovskite photo absorber reached a 33.7% independently certified PCE for a device area of 1 square centimeter.
- 2 August 2024
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 385 (6708) , 533-538
Top Cited PapersEnhanced cation interaction in perovskites for efficient tandem solar cells with silicon
To achieve the full potential of monolithic perovskite/silicon tandem solar cells, crystal defects and film inhomogeneities in the perovskite top cell must be minimized. We discuss the use of methylenediammonium dichloride as an additive to the perovskite precursor solution, resulting in the incorporation of in situ–formed tetrahydrotriazinium (THTZ-H + ) into the perovskite lattice upon film crystallization. The cyclic nature of the THTZ-H + cation enables a strong interaction with the lead octahedra of the perovskite lattice through the formation of hydrogen bonds with iodide in multiple directions. This structure improves the device power conversion efficiency (PCE) and phase stability of 1.68 electron volts perovskites under prolonged light and heat exposure under 1-sun illumination at 85°C. Monolithic perovskite/silicon tandems incorporating THTZ-H + in the perovskite photo absorber reached a 33.7% independently certified PCE for a device area of 1 square centimeter.