Minugu Om Prakash
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Minugu Om Prakash has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Gujjala Raghavendra
Department of Mechanical Engineering, National Institute of Technology, Warangal, India
7 shared publications - Manoj Panchal
Mechanical engineering, NIT Warangal, Warangal, Telangana state, 506004, INDIA
5 shared publications S. Ojha
5 shared publicationsManoj Panchal
4 shared publicationsG. Raghavendra
NIT Warangal
2 shared publicationsP. Subhash Chandra Bose
NIT Warangal
2 shared publications
Latest Publications
- Open Access
- 1 June 2025
- Published by Elsevier in Composites Part C: Open Access
- Vol. 17
Investigation of mechanical, thermal, and tribological performance of activated carbon-glass/epoxy hybrid composites
- 1 June 2025
- Published by Elsevier in Composites Part C: Open Access
- Vol. 17
Open AccessInvestigation of mechanical, thermal, and tribological performance of activated carbon-glass/epoxy hybrid composites
- Open Access
- 5 November 2023
- Published by Atlantis Press SARL
- p. 1016-1021
Study of Wear Analysis of Chitosan Epoxy Polymer Composites
- 5 November 2023
- Published by Atlantis Press SARL
- p. 1016-1021
Open AccessStudy of Wear Analysis of Chitosan Epoxy Polymer Composites
- 21 March 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (5) , 3189-3203
Effect of biomass‐biochar content on the erosion wear performance of biochar epoxy composites
Biomass waste processing with a potential to commercialization is always concern for achieving sustainable ecosystem. In the current work, biochar was extracted from the arhar stalks (AS) and bael shells (BS) biowaste which has carbon as major constituent. As a result, biochar in particle form has excellent mechanical and tribological properties and hence when combined with epoxy forms a composite with enhanced tribological properties. In this context, the biochar epoxy composites were prepared with three different compositions of 2, 4, and 6% wt, and characterized for adsorption and solid erosion wear studies. The adsorption studies conferred that BS biochar materials consist large Brunauer–Emmet–Teller surface area, that is, 294.3393 m2/g and pore volume of 0.13166 cm3/g comparative to AS biochar materials. It was observed from the results that BS based biochar epoxy composites displayed excellent enhancement in erosion wear resistance of about 52% comparative to pure epoxy that of AS at 2%. Alongside further increment in the composition of the biochar constituent to 4% exhibited semi ductile behavior with a peak wear rate at 45° impact angle. Applications pertaining to the realized composites in the current work is expected to meet the aerospace and automotive industries in specific.
- 21 March 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (5) , 3189-3203
Effect of biomass‐biochar content on the erosion wear performance of biochar epoxy composites
Biomass waste processing with a potential to commercialization is always concern for achieving sustainable ecosystem. In the current work, biochar was extracted from the arhar stalks (AS) and bael shells (BS) biowaste which has carbon as major constituent. As a result, biochar in particle form has excellent mechanical and tribological properties and hence when combined with epoxy forms a composite with enhanced tribological properties. In this context, the biochar epoxy composites were prepared with three different compositions of 2, 4, and 6% wt, and characterized for adsorption and solid erosion wear studies. The adsorption studies conferred that BS biochar materials consist large Brunauer–Emmet–Teller surface area, that is, 294.3393 m2/g and pore volume of 0.13166 cm3/g comparative to AS biochar materials. It was observed from the results that BS based biochar epoxy composites displayed excellent enhancement in erosion wear resistance of about 52% comparative to pure epoxy that of AS at 2%. Alongside further increment in the composition of the biochar constituent to 4% exhibited semi ductile behavior with a peak wear rate at 45° impact angle. Applications pertaining to the realized composites in the current work is expected to meet the aerospace and automotive industries in specific.
- 8 February 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (4) , 2276-2287
Study of environmental behavior and its effect on solid particle erosion behavior of hierarchical porous activated carbon‐epoxy composite
Porous carbon materials have versatile physical and chemical characteristics; however, these materials are not be fully exploited as reinforcements in polymer composites. The present investigation focuses on extraction of hierarchical porous carbon and its utilization in polymer composite in order to enhance the erosion wear resistance and hardness of polymer composite. The current research work also demonstrates the wear behavior of the hierarchical porous carbon epoxy composite when exposed to different environmental conditions. The attributes of hierarchical carbon have verified through different characterization techniques, further porous carbon with optimum properties has been included as reinforcement in different ratios viz. 1, 2 and 3 wt. % to make the epoxy composites. The composites were studied for their hardness, moisture absorption and erosion wear behavior at variable impingement angles (30°, 45°, 60°, and 90°) and impingement velocities (101, 119, and 148 m/s). Moisture uptake results suggests that the increase in filler percentage increased the moisture absorption, and the highest moisture absorption was reported in composite immersed in saline water environment. It was observed that addition of activated carbon particles has enhanced hardness and wear resistance of the composite. Composite with 2 wt.% particulate reinforcement was found to be the optimum percentage of reinforcement which was subjected to 82.4% less material loss that is, erosion rate at 45° impact angle compared to neat polymer. From the erosion wear results it was further noticed that moisture absorption has deteriorated the erosion wear resistance of composites resulting in high material loss.
- 8 February 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (4) , 2276-2287
Study of environmental behavior and its effect on solid particle erosion behavior of hierarchical porous activated carbon‐epoxy composite
Porous carbon materials have versatile physical and chemical characteristics; however, these materials are not be fully exploited as reinforcements in polymer composites. The present investigation focuses on extraction of hierarchical porous carbon and its utilization in polymer composite in order to enhance the erosion wear resistance and hardness of polymer composite. The current research work also demonstrates the wear behavior of the hierarchical porous carbon epoxy composite when exposed to different environmental conditions. The attributes of hierarchical carbon have verified through different characterization techniques, further porous carbon with optimum properties has been included as reinforcement in different ratios viz. 1, 2 and 3 wt. % to make the epoxy composites. The composites were studied for their hardness, moisture absorption and erosion wear behavior at variable impingement angles (30°, 45°, 60°, and 90°) and impingement velocities (101, 119, and 148 m/s). Moisture uptake results suggests that the increase in filler percentage increased the moisture absorption, and the highest moisture absorption was reported in composite immersed in saline water environment. It was observed that addition of activated carbon particles has enhanced hardness and wear resistance of the composite. Composite with 2 wt.% particulate reinforcement was found to be the optimum percentage of reinforcement which was subjected to 82.4% less material loss that is, erosion rate at 45° impact angle compared to neat polymer. From the erosion wear results it was further noticed that moisture absorption has deteriorated the erosion wear resistance of composites resulting in high material loss.
- 23 April 2020
- Published by Wiley in Polymer Composites
- Vol. 41 (8) , 3113-3123
Mechanical characterization of arhar biomass based porous nano activated carbon polymer composites
Activated carbon material was synthesized by two stage pyrolysis and chemical activation method using arhar fiber biomass as precursor. The effect of activation temperature on the characteristics of activated carbon materials was explored. Temperatures of 700°C, 800°C, and 900°C were used for the production of activated carbon materials. BET surface area, pore size, and pore volume were studied using N2 adsorption analysis. Activated carbon prepared at 800°C temperature was found to be effective; exhibited 504.6 m2/g surface area and pore volume of 0.245569 cm3/g with micropores of less than 20 Å diameter. XRD analysis of the material exhibited broad and sharp peaks in the range of 18 to 30 (2θ), confirming amorphous structure. From thermogravimetric analysis, it was noticed that activated carbon has high thermal stability. It was left with 62% of residual mass when subjected to 1400°C temperature. Activated carbon material synthesized at 800°C was used as filler while epoxy functioned as matrix material for fabrication of composites. The effect of filler loading on the tensile strength of composites was studied. Tensile strength of composite material increased with addition of filler loading. It was observed that composite with 2% filler loading had a maximum tensile strength of 56 MPa.
- 23 April 2020
- Published by Wiley in Polymer Composites
- Vol. 41 (8) , 3113-3123
Mechanical characterization of arhar biomass based porous nano activated carbon polymer composites
Activated carbon material was synthesized by two stage pyrolysis and chemical activation method using arhar fiber biomass as precursor. The effect of activation temperature on the characteristics of activated carbon materials was explored. Temperatures of 700°C, 800°C, and 900°C were used for the production of activated carbon materials. BET surface area, pore size, and pore volume were studied using N2 adsorption analysis. Activated carbon prepared at 800°C temperature was found to be effective; exhibited 504.6 m2/g surface area and pore volume of 0.245569 cm3/g with micropores of less than 20 Å diameter. XRD analysis of the material exhibited broad and sharp peaks in the range of 18 to 30 (2θ), confirming amorphous structure. From thermogravimetric analysis, it was noticed that activated carbon has high thermal stability. It was left with 62% of residual mass when subjected to 1400°C temperature. Activated carbon material synthesized at 800°C was used as filler while epoxy functioned as matrix material for fabrication of composites. The effect of filler loading on the tensile strength of composites was studied. Tensile strength of composite material increased with addition of filler loading. It was observed that composite with 2% filler loading had a maximum tensile strength of 56 MPa.
- 14 March 2020
- Published by Springer Nature
- p. 429-437
Thermogravimetric Analysis of Biochar from Arhar Fiber Powder Prepared at Different Pyrolysis Temperatures
- 14 March 2020
- Published by Springer Nature
- p. 429-437
Thermogravimetric Analysis of Biochar from Arhar Fiber Powder Prepared at Different Pyrolysis Temperatures
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 115613
A single step process to synthesize ordered porous carbon from coconut shells-eggshells biowaste
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 115613
A single step process to synthesize ordered porous carbon from coconut shells-eggshells biowaste
- 16 May 2017
- Published by Springer Nature in Silicon
- Vol. 10 (3) , 859-867
Moisture Absorption Behavior of Treated and Untreated Eggshell Particulate Epoxy Composites
- 16 May 2017
- Published by Springer Nature in Silicon
- Vol. 10 (3) , 859-867
Moisture Absorption Behavior of Treated and Untreated Eggshell Particulate Epoxy Composites
- 20 April 2017
- Published by Springer Nature in Silicon
- Vol. 10 (3) , 825-830
Influence of Distinct Environment on the Mechanical Characteristics of Arhar Fiber Polymer Composites
- 20 April 2017
- Published by Springer Nature in Silicon
- Vol. 10 (3) , 825-830
Influence of Distinct Environment on the Mechanical Characteristics of Arhar Fiber Polymer Composites
- 13 March 2017
- Published by Springer Nature in Silicon
- Vol. 10 (2) , 627-634
Effects of Environmental Conditions on Erosion Wear of Eggshell Particulate Epoxy Composites
- 13 March 2017
- Published by Springer Nature in Silicon
- Vol. 10 (2) , 627-634
Effects of Environmental Conditions on Erosion Wear of Eggshell Particulate Epoxy Composites