Romeu Rony Cavalcante da Costa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Romeu Rony Cavalcante da Costa has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- André Costa Vieira
CMAST—Centre for Mechanical and Aerospace Science and Technologies, University of Beira Interior, Rua Marquês de Ávila e Bolama, 6201-001 Covilhã, Portugal
2 shared publications - Enio Henrique Pires Da Silva
Aeronautical Engineering Department, São Carlos School of Engineering, University of São Paulo, São Carlos 13563-120, SP, Brazil
2 shared publications Amanda Albertin Xavier da Silva
Universidade Tecnológica Federal do Paraná, Brasil
1 shared publicationAna P de Moura
Department of Mechanical Engineering, Universidade Tecnológica Federal do Paraná, UTFPR, Cornélio Procópio, PR, Brazil
1 shared publication- Camila Albertin Xavier da Silva
Universidade Tecnológica Federal do Paraná (UTFPR), Cornélio Procópio, Brazil
1 shared publication - Edson Hideki Koroishi
Universidade Tecnológica Federal do Paraná, Brazil
1 shared publication
Latest Publications
- Open Access
Accelerated Aging on the Compression Properties of a Green Polyurethane Foam: Experimental and Numerical Analysis
The aim of this work is to evaluate the changes in compression properties of a bio-based polyurethane foam after exposure to 90 °C for different periods of time, and to propose a method to extrapolate these results and use a numerical approach to predict the compression behaviour after degradation for untested conditions at different degradation times and temperatures. Bio-based polymers are an important sustainable alternative to oil-based materials. This is explained by the foaming process and the density along the material as it was possible to see in a digital image correlation analysis. After 60 days, stiffness was approximately decreased by half in both directions. The decrease in yield stress due to thermo-oxidative degradation had a minor effect in the foaming directions, changing from 352 kPa to 220 kPa after 60 days, and the transverse property was harshly impacted changing from 530 kPa to 265 kPa. The energy absorption efficiency was slightly affected by degradation. The simulation of the compression stress-strain curves were in accordance to the experimental data and made it possible to predict the changes in mechanical properties for intermediate periods of degradation time. The plateau stress for the unaged foam transverse to the foaming direction presented experimental and numerical values of 450 kPa and 470 kPa, respectively. In addition, the plateau stresses in specimens degraded for 40 days present very similar experimental and numerical results in the same direction, at 310 kPa and 300 kPa, respectively. Therefore, this paper presents important information regarding the life-span and degradation of a green PUF. It provides insights into how compression properties vary along degradation time as function of material operation temperature, according to the Arrhenius degradation equation.
Open AccessAccelerated Aging on the Compression Properties of a Green Polyurethane Foam: Experimental and Numerical Analysis
The aim of this work is to evaluate the changes in compression properties of a bio-based polyurethane foam after exposure to 90 °C for different periods of time, and to propose a method to extrapolate these results and use a numerical approach to predict the compression behaviour after degradation for untested conditions at different degradation times and temperatures. Bio-based polymers are an important sustainable alternative to oil-based materials. This is explained by the foaming process and the density along the material as it was possible to see in a digital image correlation analysis. After 60 days, stiffness was approximately decreased by half in both directions. The decrease in yield stress due to thermo-oxidative degradation had a minor effect in the foaming directions, changing from 352 kPa to 220 kPa after 60 days, and the transverse property was harshly impacted changing from 530 kPa to 265 kPa. The energy absorption efficiency was slightly affected by degradation. The simulation of the compression stress-strain curves were in accordance to the experimental data and made it possible to predict the changes in mechanical properties for intermediate periods of degradation time. The plateau stress for the unaged foam transverse to the foaming direction presented experimental and numerical values of 450 kPa and 470 kPa, respectively. In addition, the plateau stresses in specimens degraded for 40 days present very similar experimental and numerical results in the same direction, at 310 kPa and 300 kPa, respectively. Therefore, this paper presents important information regarding the life-span and degradation of a green PUF. It provides insights into how compression properties vary along degradation time as function of material operation temperature, according to the Arrhenius degradation equation.
- 27 December 2022
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 12 (1) , 191-200
Vibration Attenuation of a Composite Beam by Fuzzy Control
- 27 December 2022
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 12 (1) , 191-200
Vibration Attenuation of a Composite Beam by Fuzzy Control
- 7 January 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 236 (7) , 1408-1418
Compression and morphological properties of a bio-based polyurethane foam with aluminum hydroxide
Compression and morphological evaluation of a new bio-based polyurethane foam (PUF) with aluminum hydroxide (ATH) added as flame retardant were carried out. The PUF was obtained from a blend of vegetable oils. Compression behavior of the polyurethane with different mass fractions of flame retardant (ATH) was investigated according to ASTM D1621–16. The ATH addition highly increased the compression yield strength of the specimens, going from 0.85 MPa (no ATH) to 2.34 MPa ( + 50%wt ATH). The compression yield strain did not show a noteworthy difference up to 40% ATH, presenting a significant decrement in the PUF + 50%ATH. The compression elasticity modulus increased from 15.40 MPa (no ATH) up to 139.77 MPa ( + 50%wt ATH). SEM images were used in order to evaluate the morphological structure of the foam. Regarding the cell sizes, there was no pattern observed, therefore, the cell sizes were adopted as random. The shapes of the cells were detected as elliptical in two different directions in the same cross-sectional area. The digital image correlation (DIC) technique showed higher strain values where the transverse ellipsoid-shaped cells were located, therefore, the load-oriented ellipsoids presented higher stiffness. Thus, the results for PUF with addition of ATH show that the bio-based material presented an important improvement in the compression properties, which allows this material to become more useful for different applications, such as furniture, building and automobile industries, as well as sandwich structures.
- 7 January 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 236 (7) , 1408-1418
Compression and morphological properties of a bio-based polyurethane foam with aluminum hydroxide
Compression and morphological evaluation of a new bio-based polyurethane foam (PUF) with aluminum hydroxide (ATH) added as flame retardant were carried out. The PUF was obtained from a blend of vegetable oils. Compression behavior of the polyurethane with different mass fractions of flame retardant (ATH) was investigated according to ASTM D1621–16. The ATH addition highly increased the compression yield strength of the specimens, going from 0.85 MPa (no ATH) to 2.34 MPa ( + 50%wt ATH). The compression yield strain did not show a noteworthy difference up to 40% ATH, presenting a significant decrement in the PUF + 50%ATH. The compression elasticity modulus increased from 15.40 MPa (no ATH) up to 139.77 MPa ( + 50%wt ATH). SEM images were used in order to evaluate the morphological structure of the foam. Regarding the cell sizes, there was no pattern observed, therefore, the cell sizes were adopted as random. The shapes of the cells were detected as elliptical in two different directions in the same cross-sectional area. The digital image correlation (DIC) technique showed higher strain values where the transverse ellipsoid-shaped cells were located, therefore, the load-oriented ellipsoids presented higher stiffness. Thus, the results for PUF with addition of ATH show that the bio-based material presented an important improvement in the compression properties, which allows this material to become more useful for different applications, such as furniture, building and automobile industries, as well as sandwich structures.
- 4 March 2021
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 55 (21) , 2857-2866
Structural and mechanical characterization of polyurethane-CaCO3 composites synthesized at high calcium carbonate loading: An experimental and theoretical study
Due to its exceptional biocompatibility, Polyurethane (PU) reinforced with calcium carbonate (CaCO3) is a composite material with significant biomedical applications. However, much of the currently known mechanical and chemical information regarding composites has been obtained at low and moderate CaCO3 content levels. This study employs experimental and theoretical tools to evaluate the structural, morphological, and mechanical properties of pristine polyurethane, and when doped with CaCO3 at 25 and 50 wt.%. In the experiments the samples are characterized using X-ray diffraction (XRD), infrared spectrophotometry (FT-IR), scanning electron microscopy (SEM), and tensile and flexural mechanical tests, while theoretical calculations are performed to evaluate the carbonate-polymer interaction. The XRD and FT-IR results indicate that CaCO3 is at the calcite phase and that PU-CaCO3 materials exhibit a broadening of bands related to the NH2 group. This result is explained using theoretical calculations that demonstrate a weak interaction between those molecules with the CaCO3 surface, where the molecule-calcite interaction occurs primarily through the NH2 molecular link. With respect to mechanical behaviour, the results show less fracture resistance and greater stiffness for the materials containing CaCO3, compared to those containing only PU. These results are explained in terms of the stress concentration due to CaCO3 within the polymer. Finally, the results detailed in this paper show that a high calcium carbonate loading is suitable for increasing the rigidity and decreasing the fracture toughness of the biomaterial, in association with a reduction of the plastic region.
- 4 March 2021
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 55 (21) , 2857-2866
Structural and mechanical characterization of polyurethane-CaCO3 composites synthesized at high calcium carbonate loading: An experimental and theoretical study
Due to its exceptional biocompatibility, Polyurethane (PU) reinforced with calcium carbonate (CaCO3) is a composite material with significant biomedical applications. However, much of the currently known mechanical and chemical information regarding composites has been obtained at low and moderate CaCO3 content levels. This study employs experimental and theoretical tools to evaluate the structural, morphological, and mechanical properties of pristine polyurethane, and when doped with CaCO3 at 25 and 50 wt.%. In the experiments the samples are characterized using X-ray diffraction (XRD), infrared spectrophotometry (FT-IR), scanning electron microscopy (SEM), and tensile and flexural mechanical tests, while theoretical calculations are performed to evaluate the carbonate-polymer interaction. The XRD and FT-IR results indicate that CaCO3 is at the calcite phase and that PU-CaCO3 materials exhibit a broadening of bands related to the NH2 group. This result is explained using theoretical calculations that demonstrate a weak interaction between those molecules with the CaCO3 surface, where the molecule-calcite interaction occurs primarily through the NH2 molecular link. With respect to mechanical behaviour, the results show less fracture resistance and greater stiffness for the materials containing CaCO3, compared to those containing only PU. These results are explained in terms of the stress concentration due to CaCO3 within the polymer. Finally, the results detailed in this paper show that a high calcium carbonate loading is suitable for increasing the rigidity and decreasing the fracture toughness of the biomaterial, in association with a reduction of the plastic region.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 29 (4)
Design of a polymeric composite material femoral stem for hip joint implant
Hip joint prosthesis are structural components that still have some challenging problems such as the interaction of physical and biological properties between the stem and the human femur. Composite materials allow to obtain high strength structures with a large variety of modulus of elasticity and favorable characteristics in the context of orthopedic implants. Therefore, the objective of this work was the development of a prosthesis model with biopolymeric matrix, namely the polyurethane (PU) derived from castor oil, reinforced with fiberglass. The implants were made of pure PU, PU with fiberglass, and PU with glass fiber and calcium carbonate. The reinforcement was constructed in the form of a core to be inserted into the hip prosthesis. The core and stem prototypes were produced using three-dimensional printing techniques, and subsequently used in the manufacture of flexible silicone molds. The results showed good mechanical potentialities of this material for orthopedics applications.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 29 (4)
Open AccessDesign of a polymeric composite material femoral stem for hip joint implant
Hip joint prosthesis are structural components that still have some challenging problems such as the interaction of physical and biological properties between the stem and the human femur. Composite materials allow to obtain high strength structures with a large variety of modulus of elasticity and favorable characteristics in the context of orthopedic implants. Therefore, the objective of this work was the development of a prosthesis model with biopolymeric matrix, namely the polyurethane (PU) derived from castor oil, reinforced with fiberglass. The implants were made of pure PU, PU with fiberglass, and PU with glass fiber and calcium carbonate. The reinforcement was constructed in the form of a core to be inserted into the hip prosthesis. The core and stem prototypes were produced using three-dimensional printing techniques, and subsequently used in the manufacture of flexible silicone molds. The results showed good mechanical potentialities of this material for orthopedics applications.