DTDerya Z. Tansel

Derya Z. Tansel

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Derya Z. Tansel has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design of a Compliant Six-Wheeled Robot for In-Pipe Inspection with Geometry Constraints

    by Daniel R. McArthur, Derya Z. Tansel, Clint Hobart, Josh Ortiz, Stephen P. Buerger

    This paper presents the design of SPIINE, a compliant six-wheeled robot for in-pipe inspection with geometry constraints. SPIINE, the Self-Propelled Interior Inspector for Non-destructive-testing (NDT) Examination, is designed to navigate 53 mm (2 in) inner-diameter pipes with tight 90° elbows, including elbows with a curvature radius as small as 76 mm (3 in), while transmitting power and high-resolution video over long tethers verified to 110 m. In straight steel pipe, SPIINE can generate more than eight times its weight in pull force to support towing of NDT sensor payloads. We also present analytical models for estimating robot stiffness and normal-force generation along with prototype hardware tests that evaluate model accuracy. Across the tested displacement range, the vertical reaction-force model achieved a root-mean-square error of 0.21 N; for two tested pipe configurations, pull-force estimates were within 7–13% of the measured values. Hardware experiments demonstrate that SPIINE can traverse a tight 90° elbow in forward and reverse at eight tested entry roll orientations spanning 360°, generate 16.5 N of pull force in straight steel pipe, and traverse more than 60 m of mixed horizontal and vertical pipe with low measured power consumption of approximately 2–3.5 W across representative test segments.

  • H2C TDIC: Self-Propelled Interior Inspection of Networks of Small Pipes (SPIINe)

    by Albuquerque Sandia National Laboratories (Snl-Nm), Daniel McArthur, Stephen Buerger, Clinton Hobart, Derya Tansel, Joshua Ortiz

    Presentation for H2C Technology Development and Integration Coordination Meeting

  • Open Access

    Focused Epicranial Brain Stimulation by Spatial Sculpting of Pulsed Electric Fields Using High Density Electrode Arrays

    by Vishal Jain, Mats Forssell, Derya Z. Tansel, Chaitanya Goswami, Gary K. Fedder, Pulkit Grover, Maysamreza Chamanzar

    Transcranial electrical neuromodulation of the central nervous system is used as a non‐invasive method to induce neural and behavioral responses, yet targeted non‐invasive electrical stimulation of the brain with high spatial resolution remains elusive. This work demonstrates a focused, steerable, high‐density epicranial current stimulation (HD‐ECS) approach to evoke neural activity. Custom‐designed high‐density (HD) flexible surface electrode arrays are employed to apply high‐resolution pulsed electric currents through skull to achieve localized stimulation of the intact mouse brain. The stimulation pattern is steered in real time without physical movement of the electrodes. Steerability and focality are validated at the behavioral, physiological, and cellular levels using motor evoked potentials (MEPs), intracortical recording, and c‐fos immunostaining. Whisker movement is also demonstrated to further corroborate the selectivity and steerability. Safety characterization confirmed no significant tissue damage following repetitive stimulation. This method can be used to design novel therapeutics and implement next‐generation brain interfaces.


  • Open Access

    High‐Conductivity Crack‐Free 3D Electrical Interconnects Directly Printed on Soft PDMS Substrates

    by Jacob Brenneman, Derya Z. Tansel, Gary K. Fedder, Rahul Panat

    Nanoparticle 3D printing and sintering is a promising method to achieve freeform interconnects on compliant substrates for applications such as soft robotics and wearable healthcare devices. However, previous strategies to sinter metallic nanoparticles while preserving the soft polymer substrate are rife with problems such as cracking and low conductivity of the metallic features. In this paper, the mechanisms of cracking in nanoparticle‐based 3D printed and sintered stretchable interconnects are identified and architecture and processing strategies are demonstrated to achieve crack‐free interconnects fully embedded in thin (<100 μm in thickness) stretchable polydimethylsiloxane (PDMS) with external connectivity. Capillary forces between nanoparticles developed through rapid solvent evaporation in the colloidal ink is hypothesized to initiate cracking during drying. Additionally, the presence of oxygen promotes the removal of organic surfactants and binders in the nanoparticle ink which increases nanoparticle agglomeration, grain growth, and subsequently conductivity. An experimental step‐wise variation of the thermal/atmospheric process conditions supports this hypothesis and shows that the presence of air during a low temperature drying step reduces the capillary stress to produce crack‐free interconnects with high conductivities (up to 56% of bulk metal) while having an excellent compatibility with the underlying polymer materials. Finally, stretchable interconnects fully‐encapsulated in PDMS polymer, with 3D pillar architectures for external connectivity are demonstrated, thus also solving an important “last‐mile” problem in the packaging of stretchable electronics.


  • Mechanical characterization of polydimethylsiloxane (PDMS) exposed to thermal histories up to 300 °C in a vacuum environment

    by Derya Z Tansel, Jacob Brenneman, Gary K Fedder, Rahul Panat

    Flexible electronic devices consisting of sensors and interconnects integrated with a soft polymer platform are being considered for emerging applications such as smart clothing, soft robotics, conformal batteries, and biomonitoring decals. Fabrication processes for such devices can require that the polymer platform be subjected to temperatures up to 300 °C without a significant deterioration of its physical properties such as stretchability and stiffness. In this communication, we report the stress–strain behavior of relatively thin sheets of polydimethylsiloxane (PDMS) polymer (thickness ∼30 µ m) made with a base-to-hardener ratio of 20:1 and heated up to 300 °C in a vacuum environment. It is shown that in spite of the exposure to high temperatures used in this study, the PDMS sheets maintained their hyperelastic behavior as represented by the Ogden model. The elastic modulus is shown to decrease from 0.81 MPa to 0.62 MPa while average strain to failure is shown to decrease from 250% to 106% as the temperature of thermal exposure in vacuum is increased from 100 °C to 300 °C. The retention of high stretchability even after the thermal exposures opens up the possibility of high-density microelectronic circuit interconnects to be fabricated on PDMS substrates.