Junlei Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Junlei Wang has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
Ailin Jia
PetroChina Research Institute of Petroleum Exploration and Development, Department of Gasfield Development, Beijing 100083, China
2 shared publicationsYadong Qi
2 shared publications- Yadong Qi
PetroChina Research Institute of Petroleum Exploration and Development, Department of Gasfield Development, Beijing 100083, China
2 shared publications - Yunsheng Wei
PetroChina Research Institute of Petroleum Exploration and Development
2 shared publications - Yunsheng Wei
PetroChina Research Institute of Petroleum Exploration & Development, Beijing 100083, China
2 shared publications Ai-Lin Jia
PetroChina Research Institute of Petroleum Exploration & Development
1 shared publication
Latest Publications
- Open Access
Thermo-Mechanical Controls on Permeability in Deep Fractured-Porous Carbonates During Underground Gas Storage
Deep fractured-porous carbonate reservoirs used for underground gas storage (UGS) experience simultaneous changes in temperature and effective stress during cyclic injection and withdrawal, so predicting permeability evolution is essential for evaluating long-term injectivity and deliverability. Using the Xiangguosi UGS as the engineering background, we measured steady-state gas permeability of three fractured-porous carbonate cores under representative conditions (20–80 °C; 15–35 MPa). Permeability decreases nonlinearly under coupled loading: changing temperature or effective stress alone typically reduces permeability by 30–70%, while the maximum reduction under concurrent increases in both variables exceeds 80% relative to the reference condition. An exponential model was fitted to quantify the decay parameter of permeability with effective stress (0.038–0.046 MPa−1) and with temperature (0.016–0.020 °C−1). In addition, the temperature-related exponential decay parameter decreases with increasing effective stress, because compliant fractures and larger pores are progressively pre-closed, weakening the permeability response to temperature. Finally, we propose a parsimonious separable exponential model that reproduces the measurements with a mean relative error below 12%, providing a practical constitutive relation for multiphysics simulations of UGS in fractured-porous carbonates.
Open AccessThermo-Mechanical Controls on Permeability in Deep Fractured-Porous Carbonates During Underground Gas Storage
Deep fractured-porous carbonate reservoirs used for underground gas storage (UGS) experience simultaneous changes in temperature and effective stress during cyclic injection and withdrawal, so predicting permeability evolution is essential for evaluating long-term injectivity and deliverability. Using the Xiangguosi UGS as the engineering background, we measured steady-state gas permeability of three fractured-porous carbonate cores under representative conditions (20–80 °C; 15–35 MPa). Permeability decreases nonlinearly under coupled loading: changing temperature or effective stress alone typically reduces permeability by 30–70%, while the maximum reduction under concurrent increases in both variables exceeds 80% relative to the reference condition. An exponential model was fitted to quantify the decay parameter of permeability with effective stress (0.038–0.046 MPa−1) and with temperature (0.016–0.020 °C−1). In addition, the temperature-related exponential decay parameter decreases with increasing effective stress, because compliant fractures and larger pores are progressively pre-closed, weakening the permeability response to temperature. Finally, we propose a parsimonious separable exponential model that reproduces the measurements with a mean relative error below 12%, providing a practical constitutive relation for multiphysics simulations of UGS in fractured-porous carbonates.
- Open Access
Water Shutoff with Polymer Gels in a High-Temperature Gas Reservoir in China: A Success Story
Gel treatments have been widely applied to control water production in oil and gas reservoirs. However, for water shutoff in dense gas reservoirs, most gel-based treatments focus on individual wells rather than the entire reservoir, exhibiting limited treatment depth, poor durability, and inadequate repeatability Notably, formation damage is a primary consideration in treatment design—most dense gas reservoirs have a permeability of less than 1 mD, making them highly susceptible to damage by formation water, let alone viscous polymer gels. Constrained by well completion methods, gelant can only be bullheaded into deep gas wells in most scenarios. Due to the poor gas/water selective plugging capability of conventional gels, the injected gelant tends to enter both gas and water zones, simultaneously plugging fluid flow in both. Although several techniques have been developed to re-establish gas flow paths post-treatment, treating gas-producing zones remains risky when no effective barrier exists between water and gas strata. Additionally, most water/gas selective plugging materials lack sufficient thermal stability under high-temperature and high-salinity (HTHS) gas reservoir conditions, and their injectivity and field feasibility still require further optimization. To address these challenges, treatment design should be optimized using non-selective gel materials, shifting the focus from directly preventing formation water invasion into individual wells to mitigating or slowing water invasion across the entire gas reservoir. This approach can be achieved by placing large-volume gels along major water flow paths via fully watered-out wells located at structurally lower positions. Furthermore, the drainage capacity of these wells can be preserved by displacing the gel slug to the far-wellbore region, thereby dissipating water-driven energy. This study evaluates the viability of placing gels in fully watered-out wells at structurally lower positions in an edge-water drive gas reservoir to slow water invasion into structurally higher production wells interconnected via numerous microfractures and high-permeability streaks. The gel system primarily comprises polyethyleneimine (PEI), a terpolymer, and nanofibers. Key properties of the gel system are as follows: Static gelation time: 6 h; Elastic modulus of fully crosslinked gel: 8.6 Pa; Thermal stability: Stable in formation water at 130 °C for over 3 months; Injectivity: Easily placed in a 219 mD rock matrix with an injection pressure gradient of 0.8 MPa/m at an injection rate of 1 mL/min; and Plugging performance: Excellent sealing effect on microfractures, with a water breakthrough pressure gradient of 2.25 MPa/m in 0.1 mm fractures. During field implementation, cyclic gelant injections combined with over-displacement techniques were employed to push the gel slug deep into the reservoir while maintaining well drainage capacity. The total volumes of injected fluid and gelant were 2865 m3 and 1400 m3, respectively. Production data and tracer test results from adjacent wells confirmed that the water invasion rate was successfully reduced from 59 m/d to 35 m/d. The pilot test results validate that placing gels in fully watered-out wells at structurally lower positions is a viable strategy to protect the production of gas wells at structurally higher positions.
Open AccessWater Shutoff with Polymer Gels in a High-Temperature Gas Reservoir in China: A Success Story
Gel treatments have been widely applied to control water production in oil and gas reservoirs. However, for water shutoff in dense gas reservoirs, most gel-based treatments focus on individual wells rather than the entire reservoir, exhibiting limited treatment depth, poor durability, and inadequate repeatability Notably, formation damage is a primary consideration in treatment design—most dense gas reservoirs have a permeability of less than 1 mD, making them highly susceptible to damage by formation water, let alone viscous polymer gels. Constrained by well completion methods, gelant can only be bullheaded into deep gas wells in most scenarios. Due to the poor gas/water selective plugging capability of conventional gels, the injected gelant tends to enter both gas and water zones, simultaneously plugging fluid flow in both. Although several techniques have been developed to re-establish gas flow paths post-treatment, treating gas-producing zones remains risky when no effective barrier exists between water and gas strata. Additionally, most water/gas selective plugging materials lack sufficient thermal stability under high-temperature and high-salinity (HTHS) gas reservoir conditions, and their injectivity and field feasibility still require further optimization. To address these challenges, treatment design should be optimized using non-selective gel materials, shifting the focus from directly preventing formation water invasion into individual wells to mitigating or slowing water invasion across the entire gas reservoir. This approach can be achieved by placing large-volume gels along major water flow paths via fully watered-out wells located at structurally lower positions. Furthermore, the drainage capacity of these wells can be preserved by displacing the gel slug to the far-wellbore region, thereby dissipating water-driven energy. This study evaluates the viability of placing gels in fully watered-out wells at structurally lower positions in an edge-water drive gas reservoir to slow water invasion into structurally higher production wells interconnected via numerous microfractures and high-permeability streaks. The gel system primarily comprises polyethyleneimine (PEI), a terpolymer, and nanofibers. Key properties of the gel system are as follows: Static gelation time: 6 h; Elastic modulus of fully crosslinked gel: 8.6 Pa; Thermal stability: Stable in formation water at 130 °C for over 3 months; Injectivity: Easily placed in a 219 mD rock matrix with an injection pressure gradient of 0.8 MPa/m at an injection rate of 1 mL/min; and Plugging performance: Excellent sealing effect on microfractures, with a water breakthrough pressure gradient of 2.25 MPa/m in 0.1 mm fractures. During field implementation, cyclic gelant injections combined with over-displacement techniques were employed to push the gel slug deep into the reservoir while maintaining well drainage capacity. The total volumes of injected fluid and gelant were 2865 m3 and 1400 m3, respectively. Production data and tracer test results from adjacent wells confirmed that the water invasion rate was successfully reduced from 59 m/d to 35 m/d. The pilot test results validate that placing gels in fully watered-out wells at structurally lower positions is a viable strategy to protect the production of gas wells at structurally higher positions.
- Open Access
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Universal material balance equation for the analysis of condensate gas reservoirs with edgewater and bottomwater drive aquifer
The gas reservoir drive mechanism generally derives from either the fluid expansion within the reservoir, an external aquifer in contact with the reservoir, or a combination of both. The zero-dimensionless material balance equation (MBE) is a simple yet powerful tool to calculate the original hydrocarbons in place and determine the constant that characterizes aquifer performance. The purpose of this paper is to propose a universal MBE applicable to condensate (wet and retrograde) gas reservoirs with bottomwater drive (BWD) and edgewater drive (EWD) aquifers, which retains the simplicity of a straight-line plot of conventional MBE while accounting for the effects of water expansion and water influx. Black oil fluid formulation was first generated from compositional simulation via a properly tuned equation of state. By use of the temporal and spatial integral of governing equations of fluid flow in the reservoir phases, two forms of MBEs were, respectively, proposed in terms of gas/oil molar density and multiphase fluid volumes, and the external pressure support was considered through a water influx model, including either BWD or EWD. The key to new MBE is the reliability of saturation–pressure (SP) relationships. As for the volumetric MBE, SP relationships were fully derived from the limiting case of the unsteady-state path. As for molar MBE, SP relationships were investigated by either constant volume depletion or constant composition expansion, which results in the appropriate two-phase Z factor. Various MBEs along three paths of pressure depletion were compared with benchmark examples from reservoir numerical simulation. In addition, a workflow of regression analysis using a least-absolute-value-based straight-line fitting technique was provided, recapturing the simplicity of the straight line while accounting for all the drive mechanisms. The results show that the proposed MBE is straightforward to calculate reliable reserve estimations. The accuracy of reserve estimation would increase by ensuring consistency in solutions from multiple methods. These samples demonstrate the power of the universal material balance equation.
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Open AccessUniversal material balance equation for the analysis of condensate gas reservoirs with edgewater and bottomwater drive aquifer
The gas reservoir drive mechanism generally derives from either the fluid expansion within the reservoir, an external aquifer in contact with the reservoir, or a combination of both. The zero-dimensionless material balance equation (MBE) is a simple yet powerful tool to calculate the original hydrocarbons in place and determine the constant that characterizes aquifer performance. The purpose of this paper is to propose a universal MBE applicable to condensate (wet and retrograde) gas reservoirs with bottomwater drive (BWD) and edgewater drive (EWD) aquifers, which retains the simplicity of a straight-line plot of conventional MBE while accounting for the effects of water expansion and water influx. Black oil fluid formulation was first generated from compositional simulation via a properly tuned equation of state. By use of the temporal and spatial integral of governing equations of fluid flow in the reservoir phases, two forms of MBEs were, respectively, proposed in terms of gas/oil molar density and multiphase fluid volumes, and the external pressure support was considered through a water influx model, including either BWD or EWD. The key to new MBE is the reliability of saturation–pressure (SP) relationships. As for the volumetric MBE, SP relationships were fully derived from the limiting case of the unsteady-state path. As for molar MBE, SP relationships were investigated by either constant volume depletion or constant composition expansion, which results in the appropriate two-phase Z factor. Various MBEs along three paths of pressure depletion were compared with benchmark examples from reservoir numerical simulation. In addition, a workflow of regression analysis using a least-absolute-value-based straight-line fitting technique was provided, recapturing the simplicity of the straight line while accounting for all the drive mechanisms. The results show that the proposed MBE is straightforward to calculate reliable reserve estimations. The accuracy of reserve estimation would increase by ensuring consistency in solutions from multiple methods. These samples demonstrate the power of the universal material balance equation.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Simulation study of enhanced condensate recovery by gas injection in gas condensate reservoirs with natural water influx from lab to field
The depletion of water-driven gas condensate reservoirs is frequently accompanied by active aquifer water intrusion, which contributes to the loss of gas well productivity and the reduction in condensate recovery. Based on laboratory experiments and numerical simulations, this study aims to establish a framework from lab to field for investigating displacement mechanism and the potential to enhance condensate oil recovery in water-driven gas condensate reservoir through the gas injection. First, the phase behavior and fluid properties of condensate oil mixed with various injected gases including carbon dioxide (CO2), nitrogen (N2), and cyclic-injected gas were elucidated by incorporating pressure/volume/temperature (PVT) tube experiment and tuned state of equations (EOS). Then, the mechanisms of gas injection recovery were examined by conducting the long-core flooding experiment and numerical compositional simulation. Finally, a field case involving a waterflooded gas condensate reservoir was presented to demonstrate the feasibility of gas injection on increasing condensate recovery factor. The results show that: 1) the injection of CO2 has the best ability of dissolution enhancement, retrograde evaporation mitigation, interfacial tension reduction, and viscosity reduction of condensate oil; conversely, injecting N2 or cyclic-injection gas yields only minor difference. 2) In comparison with CO2 injection, injection of N2 and cyclic-injected gas exhibits a more pronounced effect in providing pressure support and retarding the influx of the aquifer. 3) The presence of heterogeneity accelerates the breakthrough of injected gas; additionally, the aquifer intrusion renders a volume of trapped gas immobile. Consequently, compared with the primary depletion scenario, gas injection has limited potential for recovering an additional 2%–4% of condensate oil. It is observed that when the condensate oil is dispersed throughout the formation that is highly waterflooded due to natural water influx, enhancing condensate recovery through gas injection becomes challenging.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Simulation study of enhanced condensate recovery by gas injection in gas condensate reservoirs with natural water influx from lab to field
The depletion of water-driven gas condensate reservoirs is frequently accompanied by active aquifer water intrusion, which contributes to the loss of gas well productivity and the reduction in condensate recovery. Based on laboratory experiments and numerical simulations, this study aims to establish a framework from lab to field for investigating displacement mechanism and the potential to enhance condensate oil recovery in water-driven gas condensate reservoir through the gas injection. First, the phase behavior and fluid properties of condensate oil mixed with various injected gases including carbon dioxide (CO2), nitrogen (N2), and cyclic-injected gas were elucidated by incorporating pressure/volume/temperature (PVT) tube experiment and tuned state of equations (EOS). Then, the mechanisms of gas injection recovery were examined by conducting the long-core flooding experiment and numerical compositional simulation. Finally, a field case involving a waterflooded gas condensate reservoir was presented to demonstrate the feasibility of gas injection on increasing condensate recovery factor. The results show that: 1) the injection of CO2 has the best ability of dissolution enhancement, retrograde evaporation mitigation, interfacial tension reduction, and viscosity reduction of condensate oil; conversely, injecting N2 or cyclic-injection gas yields only minor difference. 2) In comparison with CO2 injection, injection of N2 and cyclic-injected gas exhibits a more pronounced effect in providing pressure support and retarding the influx of the aquifer. 3) The presence of heterogeneity accelerates the breakthrough of injected gas; additionally, the aquifer intrusion renders a volume of trapped gas immobile. Consequently, compared with the primary depletion scenario, gas injection has limited potential for recovering an additional 2%–4% of condensate oil. It is observed that when the condensate oil is dispersed throughout the formation that is highly waterflooded due to natural water influx, enhancing condensate recovery through gas injection becomes challenging.
- 11 April 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (07) , 3601-3615
Optimization Method for Fracture-Network Design under Transient and Pseudosteady Conditions Using Unified-Fracture-Design and Deep-Learning Approaches
Summary: In unconventional shale and tight reservoirs, the concept of stimulated reservoir volume (SRV) is used to correlate the volume of total injected proppant with well performance. The SRV configuration consists of primary fractures connected to the wellbore and secondary fractures intersecting primary fractures. SRV productivity is determined by fracture conductivity, fracture dimensions, and network complexity, which also vary with time. This work presents an extension of the unified-fracture-design (UFD) approach to account for not only the pseudosteady state (PSS) but also transient flow regimes and ultimately optimize SRV for maximizing well performance. A generalized productivity index (PI) for both the transient and PSS regimes is presented to improve well performance by searching for the maximum PI over time. In addition, a surrogate model is developed to accelerate the optimization. This study demonstrates that the UFD enables the determination of the optimal fracture network conductivity and complexity that contribute to the maximum PI with a given proppant volume. The optimal SRV design is time-dependent until the PSS is reached. The surrogate model not only improves the computational efficiency but also delivers high precision, which means far less computational burden than the traditional parametric-sensitivity analysis.
- 11 April 2024
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (07) , 3601-3615
Optimization Method for Fracture-Network Design under Transient and Pseudosteady Conditions Using Unified-Fracture-Design and Deep-Learning Approaches
Summary: In unconventional shale and tight reservoirs, the concept of stimulated reservoir volume (SRV) is used to correlate the volume of total injected proppant with well performance. The SRV configuration consists of primary fractures connected to the wellbore and secondary fractures intersecting primary fractures. SRV productivity is determined by fracture conductivity, fracture dimensions, and network complexity, which also vary with time. This work presents an extension of the unified-fracture-design (UFD) approach to account for not only the pseudosteady state (PSS) but also transient flow regimes and ultimately optimize SRV for maximizing well performance. A generalized productivity index (PI) for both the transient and PSS regimes is presented to improve well performance by searching for the maximum PI over time. In addition, a surrogate model is developed to accelerate the optimization. This study demonstrates that the UFD enables the determination of the optimal fracture network conductivity and complexity that contribute to the maximum PI with a given proppant volume. The optimal SRV design is time-dependent until the PSS is reached. The surrogate model not only improves the computational efficiency but also delivers high precision, which means far less computational burden than the traditional parametric-sensitivity analysis.
- Open Access
Pressure Transient Test Analysis for Deep Fractured Gas Reservoirs in Tarim Basin
Fractures are common features in deep gas reservoirs with strong heterogeneity, which are generally evaluated by well-testing analysis. Based on the characteristics of a variety of spatial scales from microscopic fractures to macroscopic faults in the Kuche area, this paper investigated the pressure behavior of naturally fractured gas reservoirs by using four typical patterns, including the Warren–Root model, radial composite model, dual-flow-state model, and local heterogeneity model. As a result, typical well-testing curves and parameter sensitivity analysis were demonstrated in detail. Furthermore, the pressure transient behavior of multi-scaled fractured reservoirs was identified by use of a state-of-the-art workflow. The analysis shows that the four patterns and their identification processes were feasible for the inversion of reservoir parameters in fractured gas reservoirs. Combined with dynamic data, the proposed method could further guide the optimization of development schemes and is of great significance for the development of fractured gas reservoirs.
Open AccessPressure Transient Test Analysis for Deep Fractured Gas Reservoirs in Tarim Basin
Fractures are common features in deep gas reservoirs with strong heterogeneity, which are generally evaluated by well-testing analysis. Based on the characteristics of a variety of spatial scales from microscopic fractures to macroscopic faults in the Kuche area, this paper investigated the pressure behavior of naturally fractured gas reservoirs by using four typical patterns, including the Warren–Root model, radial composite model, dual-flow-state model, and local heterogeneity model. As a result, typical well-testing curves and parameter sensitivity analysis were demonstrated in detail. Furthermore, the pressure transient behavior of multi-scaled fractured reservoirs was identified by use of a state-of-the-art workflow. The analysis shows that the four patterns and their identification processes were feasible for the inversion of reservoir parameters in fractured gas reservoirs. Combined with dynamic data, the proposed method could further guide the optimization of development schemes and is of great significance for the development of fractured gas reservoirs.
- Open Access
- 26 November 2020
- Published by Hindawi Limited in Geofluids
- Vol. 2020, 1-17
Revising Transient-Pressure Solution for Vertical Well Intersected by a Partially Penetrating Fracture with Non-Darcy Flow Effect
The principle purpose of this work is to formulate an accurate mathematical model to evaluate the transient pressure behavior of a well intercepted by a partially penetrating vertical fracture (PPVF) with non-Darcy flow effect. Fracture conductivity is taken into account by coupling the three-dimensional flow in reservoir and the two-dimensional flow within fracture; the Barree-Conway model is incorporated into the model to analyze non-Darcy flow behavior in fracture, which leads to the nonlinearity of the governing equations. A high-effective iterative algorithm using a combined technique of fracture-panel discretization and dimension transform is developed to render the nonlinear equations amenable to analytical linear treatment. On the basis of the solutions, the pressure response and its derivative type curves were generated to identify the evolution of flow regimes with time. Furthermore, the influences of fracture conductivity, penetration ratio, and non-Darcy characteristic parameters on pressure response are investigated. The results show that PPVF exhibits five typical flow regimes, and analytical solutions for each flow regime are similar to that for a fully penetrating vertical fracture (FPVF) that can be correlated with the penetration ratio and apparent conductivity. The non-Darcy flow effect is found to have more significant effect on the low and moderate conductivity, especially in early-stage flow regimes. When the penetration ratio is smaller than 0.5, the pressure behavior exhibit a more remarkable variation with penetration ratio. This study provides a better insight into understanding the influence of non-Darcy flow on flow regime identification.
- 26 November 2020
- Published by Hindawi Limited in Geofluids
- Vol. 2020, 1-17
Open AccessRevising Transient-Pressure Solution for Vertical Well Intersected by a Partially Penetrating Fracture with Non-Darcy Flow Effect
The principle purpose of this work is to formulate an accurate mathematical model to evaluate the transient pressure behavior of a well intercepted by a partially penetrating vertical fracture (PPVF) with non-Darcy flow effect. Fracture conductivity is taken into account by coupling the three-dimensional flow in reservoir and the two-dimensional flow within fracture; the Barree-Conway model is incorporated into the model to analyze non-Darcy flow behavior in fracture, which leads to the nonlinearity of the governing equations. A high-effective iterative algorithm using a combined technique of fracture-panel discretization and dimension transform is developed to render the nonlinear equations amenable to analytical linear treatment. On the basis of the solutions, the pressure response and its derivative type curves were generated to identify the evolution of flow regimes with time. Furthermore, the influences of fracture conductivity, penetration ratio, and non-Darcy characteristic parameters on pressure response are investigated. The results show that PPVF exhibits five typical flow regimes, and analytical solutions for each flow regime are similar to that for a fully penetrating vertical fracture (FPVF) that can be correlated with the penetration ratio and apparent conductivity. The non-Darcy flow effect is found to have more significant effect on the low and moderate conductivity, especially in early-stage flow regimes. When the penetration ratio is smaller than 0.5, the pressure behavior exhibit a more remarkable variation with penetration ratio. This study provides a better insight into understanding the influence of non-Darcy flow on flow regime identification.
- 25 November 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 143 (8) , 1-11
Optimization of Managed Drawdown for a Well With Stress-Sensitive Conductivity Fractures: Workflow and Case Study
The effect of bottomhole-pressure (BHP) drawdown schedule on the well performance is generally attributed to the stress sensitivity in propped finite-conductivity fractures. The purpose of this work is to develop a detailed workflow of optimizing BHP drawdown schedule to improve long-term performance by finding a tradeoff between delaying conductivity degradation and maintaining drawdown. First, according to experimental data of propped fracture, an alternative relationship between conductivity and pressure drawdown is developed to mimic the change of fracture conductivity with effective stress. Second, based on the dimension-transformation technique, the coupled fracture-reservoir model is semi-analytically solved and seamlessly generates the time-dependent equation (i.e., transient inflow performance relationship (IPR)) which provides the production rate response to any BHP variation. Next, the value of BHP on the reversal behavior of rate is defined as the optimum BHP on the specified time-dependent IPR, and then the optimum profile of BHP drawdown over time is achieved. Finally, we corroborate the effectiveness of this workflow with a field case from Zhaotong shale in China. Field case substantiates that (1) the well with restricted drawdown has more advantage of improving the performance than that with unrestricted drawdown and (2) after inputting the optimum BHP drawdown into the history-unrestricted case, the long-term cumulative gas production could indeed be increased.
- 25 November 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 143 (8) , 1-11
Optimization of Managed Drawdown for a Well With Stress-Sensitive Conductivity Fractures: Workflow and Case Study
The effect of bottomhole-pressure (BHP) drawdown schedule on the well performance is generally attributed to the stress sensitivity in propped finite-conductivity fractures. The purpose of this work is to develop a detailed workflow of optimizing BHP drawdown schedule to improve long-term performance by finding a tradeoff between delaying conductivity degradation and maintaining drawdown. First, according to experimental data of propped fracture, an alternative relationship between conductivity and pressure drawdown is developed to mimic the change of fracture conductivity with effective stress. Second, based on the dimension-transformation technique, the coupled fracture-reservoir model is semi-analytically solved and seamlessly generates the time-dependent equation (i.e., transient inflow performance relationship (IPR)) which provides the production rate response to any BHP variation. Next, the value of BHP on the reversal behavior of rate is defined as the optimum BHP on the specified time-dependent IPR, and then the optimum profile of BHP drawdown over time is achieved. Finally, we corroborate the effectiveness of this workflow with a field case from Zhaotong shale in China. Field case substantiates that (1) the well with restricted drawdown has more advantage of improving the performance than that with unrestricted drawdown and (2) after inputting the optimum BHP drawdown into the history-unrestricted case, the long-term cumulative gas production could indeed be increased.
- Open Access
- 30 April 2020
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 56 (5)
An Alternative BEM for Simulating the Flow Behavior of a Leaky Confined Fractured Aquifer With the Use of the Semianalytical Approach
This study developed an alternative boundary element method (BEM) to simulate the transient flow behavior of groundwater induced by well extraction in a confined fractured aquifer containing a network of discrete or connected fractures. The matrix flow, network‐fracture flow, and matrix‐fracture fluid exchange were considered. The aquifer was treated as a heterogeneous whole that consisted of fracture and matrix blocks with locally homogeneous hydraulic properties. The fractures were explicitly represented to be of true finite volume rather than nonrepresentational line sources. A semianalytical solution was developed based on the theory of a BEM in the Laplace transform domain, but the analytical Green's function was used for the bounded domain rather than the free‐space Green's function in a conventional BEM. Case studies were presented in order to investigate the flow exchange behavior between the matrix and fractures and the corresponding transient drawdown response. The results showed that (1) exchange flux distribution calculated with the classical infinitesimal fracture model was consistent with the difference of the normal drawdown derivative values on both sides of the fracture body in our model. (2) When the well was in the matrix, the fractures acted as both highly conductive conduits and leaky faults, and the drawdown derivative behaviors resembled the characteristics of a dual‐porosity reservoir model. (3) When the well was in the network fracture and when the volume of fracture was of the same order of magnitude as the matrix, the drawdown derivative might exhibit the look‐alike behavior of a dual‐porosity model.
- 30 April 2020
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 56 (5)
Open AccessAn Alternative BEM for Simulating the Flow Behavior of a Leaky Confined Fractured Aquifer With the Use of the Semianalytical Approach
This study developed an alternative boundary element method (BEM) to simulate the transient flow behavior of groundwater induced by well extraction in a confined fractured aquifer containing a network of discrete or connected fractures. The matrix flow, network‐fracture flow, and matrix‐fracture fluid exchange were considered. The aquifer was treated as a heterogeneous whole that consisted of fracture and matrix blocks with locally homogeneous hydraulic properties. The fractures were explicitly represented to be of true finite volume rather than nonrepresentational line sources. A semianalytical solution was developed based on the theory of a BEM in the Laplace transform domain, but the analytical Green's function was used for the bounded domain rather than the free‐space Green's function in a conventional BEM. Case studies were presented in order to investigate the flow exchange behavior between the matrix and fractures and the corresponding transient drawdown response. The results showed that (1) exchange flux distribution calculated with the classical infinitesimal fracture model was consistent with the difference of the normal drawdown derivative values on both sides of the fracture body in our model. (2) When the well was in the matrix, the fractures acted as both highly conductive conduits and leaky faults, and the drawdown derivative behaviors resembled the characteristics of a dual‐porosity reservoir model. (3) When the well was in the network fracture and when the volume of fracture was of the same order of magnitude as the matrix, the drawdown derivative might exhibit the look‐alike behavior of a dual‐porosity model.