Mariusz Stegliński
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mariusz Stegliński has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Łukasz Kaczmarek
Institute of Materials Science and Engineering, Lodz University of Technology, Stefanowskiego 1/15 St., 90-537 Lodz, Poland
3 shared publications - Adam Roślak
Lodz University of Technology, Institute of Material Science and Engineering, 1/15 Stefanowskiego Str., 90-537 Łódź, Poland
1 shared publication Anastasiya Nikolaevna Petrova
FSBI Ural Branch of the Russian Academy of Sciences, st. S. Kovalevskaya, 18, Ekaterinburg, Sverdlovskaâ, 620990, RUSSIAN FEDERATION
1 shared publication- Bartłomiej Januszewicz
Institute of Material Science and Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, 90-924 Lodz, Poland
1 shared publication Bogusława Adamczyk-Cieślak
Warsaw University of Technology Faculty of Materials Science and Engineering, Wołoska 141, Warszawa, 02-507, POLAND
1 shared publicationIrina Brodova
FSBI Ural Branch of the Russian Academy of Sciences, st. S. Kovalevskaya, 18, Ekaterinburg, Sverdlovskaâ, 620990, RUSSIAN FEDERATION
1 shared publication
Latest Publications
- Open Access
- 30 June 2025
- Published by MDPI AG in Preprints.org
Analysis of Strength Characteristics of Epoxy Resins with a Graphene Powder
This article explores the problem of energy conversion and the related storage of hydrogen as an alternative energy source. A method of altering traditional pressure vessels using a composite material based on epoxy resin and graphene is proposed. The test plan for verifying its mechanical properties has been defined. A quantum chemical simulation in Scigress software was performed to analyse the electron distribution in the macromolecules of the epoxy resin and flake graphene. Based on the results of the strength analysis, the strength properties of the composite and the physicochemical changes at the epoxy resin-graphene. It has been proven that the epoxy resin LG 700 with 0.25% by weight of reduced graphene oxide is a potential material for the modification of pressure vessels. The reason behind it is the possibility of improving the mechanical properties of the epoxy resin due to the reorganisation of the polymer chains in the graphene flake region. This effect supports the formation of semicrystalline regions, which can enhance mechanical properties.
- 30 June 2025
- Published by MDPI AG in Preprints.org
Open AccessAnalysis of Strength Characteristics of Epoxy Resins with a Graphene Powder
This article explores the problem of energy conversion and the related storage of hydrogen as an alternative energy source. A method of altering traditional pressure vessels using a composite material based on epoxy resin and graphene is proposed. The test plan for verifying its mechanical properties has been defined. A quantum chemical simulation in Scigress software was performed to analyse the electron distribution in the macromolecules of the epoxy resin and flake graphene. Based on the results of the strength analysis, the strength properties of the composite and the physicochemical changes at the epoxy resin-graphene. It has been proven that the epoxy resin LG 700 with 0.25% by weight of reduced graphene oxide is a potential material for the modification of pressure vessels. The reason behind it is the possibility of improving the mechanical properties of the epoxy resin due to the reorganisation of the polymer chains in the graphene flake region. This effect supports the formation of semicrystalline regions, which can enhance mechanical properties.
- Open Access
- 19 July 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (8) , 086503
Effect of T6I6 tempering on the coherence between core/shell precipitates and a solid solution in the 2024 aluminium alloy
Heat treatment of materials, including—in particular—two-stage T6I6 treatment, enables the nucleation of precipitates with a two-phase structure: core and shell. The above-mentioned treatment can be used to harden materials by selecting suitable treatment parameters and the chemical composition of the material that initiates a selective diffusion of the alloying elements. In this paper, tests of the T6I6 treatment were carried out on the EN AW-2024 alloy. The aluminium alloy was subjected to T6I6 treatment, and then the element distribution map was examined within the precipitate using the EDS method. The mechanical properties of the precipitate were tested using the nanoindentation method, and the kinetics of the formation of the precipitate were analysed using DSC. The impact of two-phase precipitates on the mechanical properties was determined through a static strength test, whereas the impact of the structure on the above-mentioned mechanical properties was determined based on HR-TEM observations. The results of the study confirmed the formation of a precipitate with a two-phase structure (shell; core) in the EN AW-2024 alloy, as well as the kinetics of their formation as a function of the parameters of the T6I6 process, such as temperature, duration and cooling rate. Strength tests confirmed an increase in the strength of the alloy to Rm = 520 MPa, with elongation remaining the same at A = 13.2%. HR-TEM observations, in turn, proved that the shell forming on the core is coherent with solid solution α, which means that the hardening of the alloy may occur as a sum of the Mott-Nabarro, Friedel and Ashby-Orowan mechanisms.
- 19 July 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (8) , 086503
Open AccessEffect of T6I6 tempering on the coherence between core/shell precipitates and a solid solution in the 2024 aluminium alloy
Heat treatment of materials, including—in particular—two-stage T6I6 treatment, enables the nucleation of precipitates with a two-phase structure: core and shell. The above-mentioned treatment can be used to harden materials by selecting suitable treatment parameters and the chemical composition of the material that initiates a selective diffusion of the alloying elements. In this paper, tests of the T6I6 treatment were carried out on the EN AW-2024 alloy. The aluminium alloy was subjected to T6I6 treatment, and then the element distribution map was examined within the precipitate using the EDS method. The mechanical properties of the precipitate were tested using the nanoindentation method, and the kinetics of the formation of the precipitate were analysed using DSC. The impact of two-phase precipitates on the mechanical properties was determined through a static strength test, whereas the impact of the structure on the above-mentioned mechanical properties was determined based on HR-TEM observations. The results of the study confirmed the formation of a precipitate with a two-phase structure (shell; core) in the EN AW-2024 alloy, as well as the kinetics of their formation as a function of the parameters of the T6I6 process, such as temperature, duration and cooling rate. Strength tests confirmed an increase in the strength of the alloy to Rm = 520 MPa, with elongation remaining the same at A = 13.2%. HR-TEM observations, in turn, proved that the shell forming on the core is coherent with solid solution α, which means that the hardening of the alloy may occur as a sum of the Mott-Nabarro, Friedel and Ashby-Orowan mechanisms.
- Open Access
Impact of Elevated Temperatures on Strength Properties and Microstructure of Calcium Sulfoaluminate Paste
This article is motivated by civil fire safety. Fire-prevention engineering demands a wide range of information about building materials including alternative cements, for instance CSA-cement. Because of exposure of the cement-base material to a high temperature, its strength properties deteriorate due to dehydration connected with phase and microstructure changes. Previous research indicated that the main endothermic reaction of CSA-based composite, dehydration of ettringite, might be used as a cooling system for a metal structure during fire-load. This article examines visual assessment, microstructure, density, as well as flexural and compressive strength parameters of CSA-based composite after isothermal heating at temperatures from 23 °C to 800 °C. The results of SEM/EDS investigations showed that the calcium sulfoaluminate paste may start partially re-sintering above 600 °C. Mechanical tests revealed significant reduction of strength parameters but residual compressive strength was maintained in the whole temperature range e.g., 8 MPa at 800 °C. Additionally, visual assessment of the specimens indicated that it might be possible to predict the material temperature heating based on the specific surface color. These findings add to the evidence of general knowledge about CSA hydrates.
Open AccessImpact of Elevated Temperatures on Strength Properties and Microstructure of Calcium Sulfoaluminate Paste
This article is motivated by civil fire safety. Fire-prevention engineering demands a wide range of information about building materials including alternative cements, for instance CSA-cement. Because of exposure of the cement-base material to a high temperature, its strength properties deteriorate due to dehydration connected with phase and microstructure changes. Previous research indicated that the main endothermic reaction of CSA-based composite, dehydration of ettringite, might be used as a cooling system for a metal structure during fire-load. This article examines visual assessment, microstructure, density, as well as flexural and compressive strength parameters of CSA-based composite after isothermal heating at temperatures from 23 °C to 800 °C. The results of SEM/EDS investigations showed that the calcium sulfoaluminate paste may start partially re-sintering above 600 °C. Mechanical tests revealed significant reduction of strength parameters but residual compressive strength was maintained in the whole temperature range e.g., 8 MPa at 800 °C. Additionally, visual assessment of the specimens indicated that it might be possible to predict the material temperature heating based on the specific surface color. These findings add to the evidence of general knowledge about CSA hydrates.
- Open Access
- 1 June 2016
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 61 (2) , 1135-1142
Synergy of the Plastic Treatment HPT and Shot Peening in Aluminium Alloy Al-Mg-Mn-Sc-Zr
An improvement in fatigue strength is one of the main factors enabling the use of high-durability Al-Mg-Mn-Sc-Zr alloys in functional components of mobile robots. As part of this study, a computer simulation was carried out using ANSYS LS-DYNA software that involved the hybridization of high pressure torsion (HPT) and shot peening (SP) forming processes. The numerical analysis was aimed at determining residual stresses and strains that affect the durability and stress characteristics of the analyzed Al alloy. Results of the study indicate that tensile stresses of σ = 300 MPa generated as a result of HPT are transformed into a beneficial stress of σ = 25 MPa resulting from plastic strains caused by SP surface treatment.
- 1 June 2016
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 61 (2) , 1135-1142
Open AccessSynergy of the Plastic Treatment HPT and Shot Peening in Aluminium Alloy Al-Mg-Mn-Sc-Zr
An improvement in fatigue strength is one of the main factors enabling the use of high-durability Al-Mg-Mn-Sc-Zr alloys in functional components of mobile robots. As part of this study, a computer simulation was carried out using ANSYS LS-DYNA software that involved the hybridization of high pressure torsion (HPT) and shot peening (SP) forming processes. The numerical analysis was aimed at determining residual stresses and strains that affect the durability and stress characteristics of the analyzed Al alloy. Results of the study indicate that tensile stresses of σ = 300 MPa generated as a result of HPT are transformed into a beneficial stress of σ = 25 MPa resulting from plastic strains caused by SP surface treatment.