Seerangan Ragu Nathan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Seerangan Ragu Nathan has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Tushar Sonar
Department of Welding Equipment and Technology, Institution of Engineering and Technology, South Ural State University (National Research University), Chelyabinsk, Russia
7 shared publications - Mikhail Ivanov
South Ural State University
6 shared publications - Chinnasamy Rajendran
Department of Mechanical Engineering, Sri Krishna College of Engineering and Technology
4 shared publications - Venkatakrishnan Balasubramanian
Annamalai University
4 shared publications - Ardula Gourav Rao
Naval Materials Research Laboratory (NMRL), Ambernath, India
3 shared publications - Prabhuraj Parasuraman
Department of Mechanical Engineering, Methodist college of Engineering and Technology, Hyderabad, India
2 shared publications
Latest Publications
- 4 June 2024
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 39 (11) , 1563-1574
Wire-cut electrical discharge machining of duplex stainless steel: a study
- 4 June 2024
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 39 (11) , 1563-1574
Wire-cut electrical discharge machining of duplex stainless steel: a study
- 16 March 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (1) , 347-363
Mathematical modelling and development of response surfaces to predict and analyze the salt fog corrosion resistance of friction stir welded AA7075-T651 alloy joints: effect of retrogression and reaging
- 16 March 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 19 (1) , 347-363
Mathematical modelling and development of response surfaces to predict and analyze the salt fog corrosion resistance of friction stir welded AA7075-T651 alloy joints: effect of retrogression and reaging
- 9 February 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (1) , 68-85
Effect of Preheating Temperature on Microstructure and Mechanical Properties of Friction Stir Welded DMR249A HSLA Steel Joints
- 9 February 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (1) , 68-85
Effect of Preheating Temperature on Microstructure and Mechanical Properties of Friction Stir Welded DMR249A HSLA Steel Joints
- 29 January 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (4) , 567-583
Processing, microstructural characterization, and mechanical properties of deep cryogenically treated steels and alloys – overview
Deep cryogenic treatment (DCT), a technique of deep subzero processing, is utilized after quenching and well preceding tempering. In DCT, the materials are subjected to a soaking period of typically 24 h at a temperature of −196 °C. The optimal soaking period varies depending on the material to be cryotreated. The microstructural characteristics and mechanical properties of ferrous and nonferrous materials are significantly enhanced using DCT resulting in improved durability and functional performance of the mechanical components. The DCT is generally performed on tool steel, stainless steel, aluminum alloys, and magnesium alloys to improve its mechanical properties. The complete transition of residual austenite to martensite and finer secondary carbide precipitation correlates with an increase in the mechanical properties of tool steel. The nonferrous materials such as aluminum and magnesium alloys showed improved mechanical properties owing to the precipitation of finer second phases in the matrix. The main objective of this review paper is to provide an overview on the history and theories of DCT, important processing parameters, and the effect of DCT on microstructure and mechanical properties of tool steel, aluminum alloys, and magnesium alloys.
- 29 January 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (4) , 567-583
Processing, microstructural characterization, and mechanical properties of deep cryogenically treated steels and alloys – overview
Deep cryogenic treatment (DCT), a technique of deep subzero processing, is utilized after quenching and well preceding tempering. In DCT, the materials are subjected to a soaking period of typically 24 h at a temperature of −196 °C. The optimal soaking period varies depending on the material to be cryotreated. The microstructural characteristics and mechanical properties of ferrous and nonferrous materials are significantly enhanced using DCT resulting in improved durability and functional performance of the mechanical components. The DCT is generally performed on tool steel, stainless steel, aluminum alloys, and magnesium alloys to improve its mechanical properties. The complete transition of residual austenite to martensite and finer secondary carbide precipitation correlates with an increase in the mechanical properties of tool steel. The nonferrous materials such as aluminum and magnesium alloys showed improved mechanical properties owing to the precipitation of finer second phases in the matrix. The main objective of this review paper is to provide an overview on the history and theories of DCT, important processing parameters, and the effect of DCT on microstructure and mechanical properties of tool steel, aluminum alloys, and magnesium alloys.
- Open Access
- 1 December 2023
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 6 (4) , 469-482
Effect of tool rotational speed on microstructure and mechanical properties of friction stir welded DMR249A high strength low alloy steel butt joints for fabrication of light weight ship building structures
- 1 December 2023
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 6 (4) , 469-482
Open AccessEffect of tool rotational speed on microstructure and mechanical properties of friction stir welded DMR249A high strength low alloy steel butt joints for fabrication of light weight ship building structures
- 14 August 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (10) , 1528-1538
Influence of tool plunging rate on mechanical properties and microstructure of friction stir welded DMR249A high strength low alloy (HSLA) steel butt joints
The main aim of this study is to analyse the influence of tool plunging rate on tool wear and stir zone characteristics of DMR249A high strength low alloy (HSLA) steel joints developed using friction stir welding (FSW). The HSLA steel plates were welded at five levels of tool plunging rates varying from 2.0 mm min−1 to 3.0 mm min−1. The tool rotational speed of 600 rpm and welding speed of 30 mm min−1 were kept constant during welding. The wear of FSW tool was analysed by microscopic observations of tool condition after welding, stir zone characteristics, weight loss measurement and pin profile analysis. The characterization techniques of optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to analyse the microstructural characteristics of stir zone of welded joints. Results disclosed that the severe degradation of FSW tool occurred due to the sudden dynamic impact load on tool pin while plunging and more diffusion of work piece material into the tool pin which leads to insufficient plasticized material flow. The tool plunging rate of 2.5 mm min−1 showed minimum tool wear and produced defect free sound joint.
- 14 August 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (10) , 1528-1538
Influence of tool plunging rate on mechanical properties and microstructure of friction stir welded DMR249A high strength low alloy (HSLA) steel butt joints
The main aim of this study is to analyse the influence of tool plunging rate on tool wear and stir zone characteristics of DMR249A high strength low alloy (HSLA) steel joints developed using friction stir welding (FSW). The HSLA steel plates were welded at five levels of tool plunging rates varying from 2.0 mm min−1 to 3.0 mm min−1. The tool rotational speed of 600 rpm and welding speed of 30 mm min−1 were kept constant during welding. The wear of FSW tool was analysed by microscopic observations of tool condition after welding, stir zone characteristics, weight loss measurement and pin profile analysis. The characterization techniques of optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to analyse the microstructural characteristics of stir zone of welded joints. Results disclosed that the severe degradation of FSW tool occurred due to the sudden dynamic impact load on tool pin while plunging and more diffusion of work piece material into the tool pin which leads to insufficient plasticized material flow. The tool plunging rate of 2.5 mm min−1 showed minimum tool wear and produced defect free sound joint.
- Open Access
- 1 March 2023
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 6 (1) , 33-45
Assessment of the influence of FSSW parameters on shear strength of dissimilar materials joint (AA6061/AZ31B)
- 1 March 2023
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 6 (1) , 33-45
Open AccessAssessment of the influence of FSSW parameters on shear strength of dissimilar materials joint (AA6061/AZ31B)
- 28 September 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (8) , 3617-3632
Characterization of AA7075 Surface Composites with Ex Situ Al2O3/SiC Reinforcements Tailored Using Friction Stir Processing
- 28 September 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (8) , 3617-3632
Characterization of AA7075 Surface Composites with Ex Situ Al2O3/SiC Reinforcements Tailored Using Friction Stir Processing
- 1 August 2016
- Published by Elsevier in Engineering Failure Analysis
- Vol. 66, 88-98
Failure analysis of tungsten based tool materials used in friction stir welding of high strength low alloy steels
- 1 August 2016
- Published by Elsevier in Engineering Failure Analysis
- Vol. 66, 88-98
Failure analysis of tungsten based tool materials used in friction stir welding of high strength low alloy steels