Zhidan Rong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhidan Rong has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Maopeng Jiao
School of Civil Engineering, Southeast University, Nanjing 211189, China
4 shared publications Lihua Zhang
3 shared publications- Yuanyuan Zhu3 shared publications
Jinyan Shi
2 shared publications- Qing Jiang2 shared publications
Wei Sun
College of Materials Science and Engineering, Southeast University, Nanjing, China
2 shared publications
Latest Publications
- Open Access
The Pore Structure Characteristics of Mortar and Its Application in the Study of Chloride Ion Transport Performance
The cement-based materials widely used in infrastructure construction, such as bridges and ports, are subjected to seawater erosion and medium erosion during their service life, and their durability has always been a concern. The diffusion coefficient of chloride ions is an important indicator in the research of cement-based materials’ durability, and the pore structure is one of the most fundamental reasons affecting the diffusion behavior of chloride ions. In this paper, Mercury intrusion porosimetry (MIP), Nuclear magnetic resonance (NMR), and Nitrogen adsorption method (NAD) were used to analyze the pore structures of mortars with different volume fractions of sands. The relationship between mortar pore structure and chloride ion diffusion coefficient was established to predict its chloride ion diffusion coefficient. It may provide a new idea for studying the durability of cement-based materials. Results indicated that similar to cement paste, the pore structure of mortar satisfied the fractal characteristics of solid phase within a certain range of pores. The most probable gel pore diameter of mortars with different sand volume fractions was about 4 nm, while the most probable capillary pore diameter was approximately 46 nm, and the critical pore diameter was ranging from 50 to 60 nm. MIP results indicated that with the increase in sand volume fraction (ϕagg), the total porosity (fmip) of the mortar decreased, satisfying the relationship of fmip = 0.1859 − 0.0789ϕagg. However, the porosity of the matrix (fbase) increased with the increase in sand volume fraction, which was due to the introduction of more interfaces by the addition of aggregates. The effective chloride ion diffusion coefficient (Dcp,base) of the matrix can be obtained by fitting. Based on this, the interface transition zone (ITZ) and the cement matrix were comprehensively considered as a whole fractal phase. The predicted value of the chloride ion diffusion coefficient obtained by the Mori–Tanaka homogenization method was in good agreement with the results obtained from rapid chloride migration (RCM) experiments, and the maximum error between the simulated and experimental values did not exceed 11%. This finding can provide new ideas for accurately predicting the chloride ion diffusion coefficient of mortar and even concrete.
Open AccessThe Pore Structure Characteristics of Mortar and Its Application in the Study of Chloride Ion Transport Performance
The cement-based materials widely used in infrastructure construction, such as bridges and ports, are subjected to seawater erosion and medium erosion during their service life, and their durability has always been a concern. The diffusion coefficient of chloride ions is an important indicator in the research of cement-based materials’ durability, and the pore structure is one of the most fundamental reasons affecting the diffusion behavior of chloride ions. In this paper, Mercury intrusion porosimetry (MIP), Nuclear magnetic resonance (NMR), and Nitrogen adsorption method (NAD) were used to analyze the pore structures of mortars with different volume fractions of sands. The relationship between mortar pore structure and chloride ion diffusion coefficient was established to predict its chloride ion diffusion coefficient. It may provide a new idea for studying the durability of cement-based materials. Results indicated that similar to cement paste, the pore structure of mortar satisfied the fractal characteristics of solid phase within a certain range of pores. The most probable gel pore diameter of mortars with different sand volume fractions was about 4 nm, while the most probable capillary pore diameter was approximately 46 nm, and the critical pore diameter was ranging from 50 to 60 nm. MIP results indicated that with the increase in sand volume fraction (ϕagg), the total porosity (fmip) of the mortar decreased, satisfying the relationship of fmip = 0.1859 − 0.0789ϕagg. However, the porosity of the matrix (fbase) increased with the increase in sand volume fraction, which was due to the introduction of more interfaces by the addition of aggregates. The effective chloride ion diffusion coefficient (Dcp,base) of the matrix can be obtained by fitting. Based on this, the interface transition zone (ITZ) and the cement matrix were comprehensively considered as a whole fractal phase. The predicted value of the chloride ion diffusion coefficient obtained by the Mori–Tanaka homogenization method was in good agreement with the results obtained from rapid chloride migration (RCM) experiments, and the maximum error between the simulated and experimental values did not exceed 11%. This finding can provide new ideas for accurately predicting the chloride ion diffusion coefficient of mortar and even concrete.
- Open Access
The Dispersion and Hydration Improvement of Silica Fume in UHPC by Carboxylic Agents
Silica fume (SF) is an essential component in ultra-high-performance concrete (UHPC) to compact the matrix, but the nucleus effect also causes rapid hydration, which results in high heat release and large shrinkage. In this paper, the carboxylic agents, including polyacrylic acid and polycarboxylate superplasticizer, were used to surface modify SF to adjust the activity to mitigate hydration at an early time and to promote continuous hydration for a long period. The surface and dispersion properties of modified SF (MSF), as well as the strength and pore structure of UHPC, were studied, and the stability of the modification was also investigated. The results demonstrated that, after treatment, the carboxylic groups were grafted on the SF surface, the dispersion of SF was improved due to the increased negative pentanal of the particle surface and the steric hindrance effect, the early hydration was delayed about 3–5 h, and the hydration heat release was also mitigated. The compressive strength of UHPC with MSF reached a maximum of 138.7 MPa at 3 days, which decreased about 3.7% more than the plain group, while flexural strength varied insignificantly. More pores and cracks were observed in the matrix with MSF, and the hydration degree was promoted with MSF addition. The grafted group on SF fell off under an alkali environment after 1 h.
Open AccessThe Dispersion and Hydration Improvement of Silica Fume in UHPC by Carboxylic Agents
Silica fume (SF) is an essential component in ultra-high-performance concrete (UHPC) to compact the matrix, but the nucleus effect also causes rapid hydration, which results in high heat release and large shrinkage. In this paper, the carboxylic agents, including polyacrylic acid and polycarboxylate superplasticizer, were used to surface modify SF to adjust the activity to mitigate hydration at an early time and to promote continuous hydration for a long period. The surface and dispersion properties of modified SF (MSF), as well as the strength and pore structure of UHPC, were studied, and the stability of the modification was also investigated. The results demonstrated that, after treatment, the carboxylic groups were grafted on the SF surface, the dispersion of SF was improved due to the increased negative pentanal of the particle surface and the steric hindrance effect, the early hydration was delayed about 3–5 h, and the hydration heat release was also mitigated. The compressive strength of UHPC with MSF reached a maximum of 138.7 MPa at 3 days, which decreased about 3.7% more than the plain group, while flexural strength varied insignificantly. More pores and cracks were observed in the matrix with MSF, and the hydration degree was promoted with MSF addition. The grafted group on SF fell off under an alkali environment after 1 h.
- 13 June 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 437
A prediction method for chloride ion diffusion coefficient of hardened cement paste based on fractal theory
- 13 June 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 437
A prediction method for chloride ion diffusion coefficient of hardened cement paste based on fractal theory
- 13 September 2023
- Published by Elsevier in Cement and Concrete Composites
- Vol. 144
Valorization and enhancement mechanism of ferrochrome slag as aggregate for manufacturing ultra-high performance concrete (UHPC)
- 13 September 2023
- Published by Elsevier in Cement and Concrete Composites
- Vol. 144
Valorization and enhancement mechanism of ferrochrome slag as aggregate for manufacturing ultra-high performance concrete (UHPC)
- Open Access
Effects of Modified Nano-SiO2 Particles on Properties of High-Performance Cement-Based Composites
In this research, silane coupling agent was used to modify the surface of nano-SiO2, particles and the effects of modified nano-SiO2 particles on the mechanical properties of high-performance cement-based composites and its mechanism were systematically studied. The results indicated that the optimum modification parameters were a coupling agent content of 10%, reaction temperature of 65 °C, and reaction time of 8 h. Compared with the unmodified nano-SiO2, the modified nano-SiO2 promoted and accelerated the hydration process of cement. The pozzolanic effect, filling effect, and nucleation effect of modified nano-SiO2 made the microstructure of the composite more compact, and thus improved static mechanical properties of cement-based composites.
Open AccessEffects of Modified Nano-SiO2 Particles on Properties of High-Performance Cement-Based Composites
In this research, silane coupling agent was used to modify the surface of nano-SiO2, particles and the effects of modified nano-SiO2 particles on the mechanical properties of high-performance cement-based composites and its mechanism were systematically studied. The results indicated that the optimum modification parameters were a coupling agent content of 10%, reaction temperature of 65 °C, and reaction time of 8 h. Compared with the unmodified nano-SiO2, the modified nano-SiO2 promoted and accelerated the hydration process of cement. The pozzolanic effect, filling effect, and nucleation effect of modified nano-SiO2 made the microstructure of the composite more compact, and thus improved static mechanical properties of cement-based composites.