TKTetiana Kimstach

Tetiana Kimstach

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tetiana Kimstach has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Identification of Effective Coefficients of Thermal Contraction of Structural States in Cast Bronze by Solving Inverse Problems of Thermodeformation Modeling

    by Tetiana Kimstach, Hennadii Shvachych, Kostiantyn Uzlov, Oleksandr Bilyi, Serhii Repiakh, Serhii Semenov, Magdalena Krupska-Klimczak

    The temperature-dependent formation of free linear shrinkage in cast CuAl7Si2Sn1.5Mn0.3 aluminum bronze was investigated using a cascade inverse-identification approach. Experimental data for 17 bronze compositions (Kᵣ = 0.41–0.85), including differential thermal analysis, quantitative metallography, and free-linear-shrinkage measurements, were used to reconstruct three genetic structure-formation pathways. Unlike conventional phase-averaging approaches, the proposed methodology identifies effective integral-average coefficients of linear thermal contraction (IA-CLTCs) of successive structural states directly from integral shrinkage data without requiring independently prescribed thermophysical properties of individual phases. The identified IA-CLTC sequences were 20.10 → 15.44 → 18.99 × 10−6 K−1 for pathway I, 21.88 → 29.40 → 11.57 × 10−6 K−1 for pathway II, and 25.90 → 36.65 → approximately 11.67 × 10−6 K−1 for pathway III. The first coefficient of pathway I was adopted as a fixed reference value. The model reproduced the experimental shrinkage with R2 = 0.998 and RMSE = 0.00562 percentage points. Conditional cascade leave-one-composition-out cross-validation yielded RMSE = 0.00995 percentage points, compared with 0.00915 percentage points for a simple linear-regression benchmark. Near the boundary between pathways II and III, the reconstructed thermal and structural-transformation contributions exhibited nearly compensating changes, although their quantitative separation remained model-dependent. Numerical sensitivity analysis revealed strong parameter correlation and limited practical identifiability for pathway III. The proposed approach therefore provides a framework for reconstructing effective temperature–deformation characteristics of successive structural states, while independent experimental validation remains necessary for their broader predictive and physical interpretation.

  • Phase composition of multicomponent aluminum bronzes criteria-based evaluation (Part 1. Supersaturated copper α-matrix and phase composition of Cu–Al–X system multicomponent bronzes stability criteria)

    by Т. V Kimstach, K. І Uzlov, G. G Shvachych, О. P Bilyi, S. I Repyakh

    Purpose. To establish structurally reliable and thermodynamically justified criteria for assessing alloys supersaturated copper α-matrix stability and predicting the phase composition of multicomponent bronzes formed under crystallization and subsequent cooling non-equilibrium conditions. Methodology. Methodology is based on thermodynamic analysis, structural-parametric approach and experimental data generalization combination. Copper matrix condition was estimated by parameter  (theoretically required and actual Cu content ratio). Thermodynamic analysis was performed within Gibbs energy minimization framework, taking into account small deviations and components with  activities connection. Structural and mechanical properties were evaluated using KR criterion. Findings. To assess in multicomponent bronzes single-phase state fixing or losing conditions, concentration parameter  has been proposed, which characterizes the conditions for solid solution non-equilibrium stability loss under casting conditions. It has been shown that at   1 conditions for secondary phase’s formation arise. KR criterion has been proposed to assess structural and mechanical properties. It has been proven that  and KR joint using provides “composition-stability-structure-properties” relationship for multicomponent aluminum bronzes comprehensive description. Originality. For the first time, quantitatively consistent system has been established of correlations between supersaturation parameter , compositional criterion KR and structural parameter  ‒ Cu–Al–Si–Mn–Sn system bronzes secondary phases volume fraction, which are formed under non-equilibrium conditions of solidification and in solid state subsequent cooling and are inherent in castings manufactured using foundry sand and metal molds. Practical value. Using indicator () and criterion (KR), proposed in the work, will allow increasing Cu–Al–Si–Mn–Sn system bronzes phase composition and properties predicting accuracy when changing their alloying elements concentrations. to reduce the time spent and resources during new alloys development or known bronze grades composition optimization by building regression and predictive models for managing their phase composition and properties. A parameter and criterion have been developed, along with an approach to creating new alloys and improving the existing alloys, their analysis, etc.

  • Corrosion of bronzes in humid air and salt fog

    by T. V. Kimstach, S. I. Repyakh

    Introduction. Corrosion is a widespread issue that is particularly critical for metal products. The consequences of corrosion may include social and environmental problems, accidents, and man-made disasters, among others. One of the approaches to addressing this problem is the use of structural bronze for manufacturing cast products, as it is resistant, particularly in natural gaseous environments. Problem. A promising bronze in this regard is the new structural non-magnetic bronze BrA7K2O1,5Mts0,3, whose corrosion resistance has not yet been studied. Purpose. To determine the kinetics and rate of unrelated corrosion in humid air and salt fog at 40 °C for bronzes of grades BrA10Zh4N4, BrA9Zh3L, BrO6Ts6S3, as well as BrA7K2O1,5Mts0,3 bronze before and after heat treatment. Materials and Methods. The study used cast samples of Ø40×10 mm made of BrA10Zh4N4, BrA9Zh3L, BrO6Ts6S3 bronzes, as well as BrA7K2O1,5Mts0,3 bronze before and after heat treatment. Corrosion kinetics were determined by measuring the change in sample mass over a period of 28 days. The mass of the samples was measured using analytical scales. The corrosion rate was calculated taking into account the density of the bronze in the samples, which was determined based on the results of hydrostatic weighing in water. Results. In humid air at 40 °C (according to accepted research methodology), all the bronzes used in this study are completely resistant. In salt fog at 40 °C, among the investigated bronzes, according to the ten-point corrosion resistance rating scale, BrA10Zh4N4 bronze has a resistance rating of 1, BrA7K2O1,5Mts0,3 bronze has a rating of 1–2, BrO6Ts6S3 bronze has a rating of 4, and BrA9Zh3L bronze has a rating of 5. A characteristic feature of the corrosion kinetics of all bronzes in humid air, as well as some bronzes in salt fog (except for BrA9Zh3L and BrO6Ts6S3), is the passivation of their surface after a certain period of exposure under the established conditions and environments in the study. Conclusions. The obtained data make it possible to assess the potential and feasibility of using cast products made of corrosion-resistant non-magnetic bronze BrA7K2O1,5Mts0,3 as a substitute for aluminum-based magnetic and non-magnetic tin-based bronzes. The use of cast parts made from this bronze will expand technical and operational capabilities, improve the reliability and durability of existing or newly developed equipment, devices, and other applications.

  • Mechanical properties and structure of Cu-Al-Si-Sn-Mn system non-magnetic cast bronzes

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, S. I Repyakh

    Purpose. To establish regularity of Cu-Al-Si-Sn-Mn system non-magnetic corrosion-resistant bronze chemical composition on structure and mechanical properties complex influence and to determine its rational composition in terms of suitability for manufacturing products by casting methods. Methodology. For bronzes mechanical properties determination FP-100/1 technique and PSW-30 pendulum machine are used. Neophot-21 microscope is used to study microstructures. Chemical elements ratio in local areas of structural components determination is carried out with SEM-515 microanalyzer. Bronzes fracture surfaces fractographic analysis is performed visually and using Coxem EM-40 electron microscope. Bronzes relative magnetic permeability is measured with Magnetomat 1.790 magnetometer. Alloys chemical composition is determined using EXPERT 4L analyzer. Findings. It has been established that Cu-Al-Si-Sn-Mn system bronze suitable for casting in sand molds should contain by weight 6.0‒7.5 % Al, 1.0‒2.5 % Si, 0.21‒0.45 % Mn and 1.0‒2.2 % Sn, and alloying chemical elements ratio and inevitable impurities, according to the formula: KR = (1‒0.01 nn) (Al-Si-Mn)/(1 + Sn)2, should be equal to 0.42‒0.85. Bronze with KR > 0.85 is low-strength, but ductile and, therefore, mainly suitable for manufacturing products from it by deformation methods. Bronze with KR < 0.42 is low-strength and brittle and it is not suitable for manufacturing products by either casting or deformation methods. Originality. For the first time, Cu-Al-Si-Sn-Mn system bronzes alloying elements complex influence on their mechanical properties and structure formation features has been determined. Cu-Al-Si-Sn-Mn system aluminum bronzes with KR value from 0.42 to 0.85 mechanical properties levels increase with Cu-solid solution relative volume fraction in their structures decreasing, that is, with KR value increasing. Practical value. The data obtained can be used as a basis for new casting, corrosion-resistant non-magnetic bronzes development that have strength and density at the level of carbon steels or aluminum bronzes alloyed with nickel and iron.


  • Determination of bronze БрА7К2О1,5Мц0,3 crystallization interval limit values and phase transformations

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, L. I Solonenko, S. I Repyakh

    Phase transformations temperatures, crystallization intervals, etc. are any alloy’s fundamental parameters. Alloys’ casting, technological and operational properties are related to them. Nevertheless, unlike two-component bronzes, such requirements for multi-component structural, non-magnetic, corrosion-resistant bronze БрА7К2О1,5Мц0,3 are absent. Purpose. For Cu-Al-Si-Sn-Mn system bronzes, crystallization intervals quantitative values (liquidus and solidus temperatures, crystallization interval size and solid phase relative share in it) have been established. БрА7К2О1,5Мц0,3 bronze’s alloying components’ synergistic and selective influence on its crystallization interval and relative fluidity indicators changing has been determined. Methodology. Well-known methods and research techniques, including thermography, differential thermal analysis, spectral chemical analysis, images analysis digital method have been used in this work. Bronzes fluidity has been assessed using spiral test. Bronze’s alloying elements’ synergistic and selective influences on its characteristics have been determined using chemical elements ratio in it (KR criterion) and experimental data results processing by Excel computer program. Findings. In bronze БрА7К2О1,5Мц0,3 with KR criterion value rising from 0.35 to 0.84, there increase liquidus, solidus temperatures and crystallization interval from 32 to 49 °C. Bronze’s alloying elements’ (Al, Si, Sn, Mn) synergistic and selective influences on its crystallization interval limit values have been determined. It has been established that conditionally-veritable fluidities of БрА7К3О1,5Мц0,3 and БрА9Ж3Л bronzes are practically the same. For Cu-Al-Si-Sn-Mn system bronzes with KR = 0.35‒2.07, solid phase relative volume fraction (SP) in crystallization temperature range is 60‒63 %. Originality. For the first time, limiting values and phase transformations for БрА7К2О1,5Мц0,3 bronze’s crystallization interval and alloying elements synergistic and selective influence on these indicators have been determined. Practical value. Based on БрА7К2О1,5Мц0,3 bronze’s chemical composition selected, mathematical models have been proposed for its liquidus and solidus temperatures calculating and for transition from dependences of solid phase t(SP) volume fraction in crystallization temperature range to temperatures’ absolute values t(SP). Their use will allow increasing the indicators of foundry and technological parameters accuracy forecasting.


  • Si and Mn effect on mechanical properties and linear shrinking of non-magnetic Cu-Al system cast bronzes

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, S. I Repyakh

    Purpose. To establish Si and Mn influence on mechanical properties level at 20 °C and aluminum bronzes structure with Al from 3 to 9 % mass content investigation. Methodology. Cast bronzes mechanical properties have been determined based on their fracture results on FP-100/1 machine and PSW-30 pendulum impactor. Microstructure has been examined using Neophot-21 optical microscope. Bronzes linear shrinkage coefficients have been calculated based on results of determining cast cylindrical samples lengths changes. Si and Mn complex influence on bronzes properties has been determined by the results of simplex triangles according to H. Scheffer plan constructing. Temperature has been measured with chromel-alumel thermocouple completed with electronic potentiometer. Bronzes chemical composition has been determined on ­EXPERT 4L analyzer. Findings. Silicon (up to 2 %) and manganese (up to 2 %) adding to Cu-Al system bronze, while aluminum content from 9 to 3 % reducing, leads to bronze ultimate tensile and yield strength decreasing during stretching and its plasticity increasing. At the same time, bronze structure, at any combination of Al, Si and Mn contents within their changes in studied limits, remains single-phase. Originality. For the first time, comprehensive assessment of influence of Si and Mn with simultaneous decrease in Al content on mechanical properties and linear shrinkage of Cu-Al-Si-Mn system cast bronzes has been carried out. It has been established that all bronzes of studied compositions have a single-phase structure and mechanical properties level that is inherent for pressure-worked bronzes. Practical value. The research results expand understanding about elemental and complex influence of Si and Mn on aluminum bronzes properties, provide an opportunity to choose a bronze with properties required level from its cast billet for deformation or to design castings taking into account the linear shrinkage values discovered in this work. The data obtained can also be the basis for new foundry, corrosion-resistant, non-magnetic bronzes, which have strength and density at the level of some carbon steel grades, development. Such materials have been used for parts that operate in chemically aggressive environments manufacturing, for control and measuring equipment and devices parts, for ship parts and naval devices, fittings, bushings, couplings, intrinsically safe tools, etc.


  • Open Access

    Perturbation of the first form of oscillations of liquid metallurgical slag in the slag car bowl in transient operating modes

    by Viktor Povorotnii, Oleksandr Yaichuk, Nataliia Karyachenko, Iryna Shcherbyna, Rodion Pohrebniak, Serhiі Zdanevych, Tetiana Kimstach, Nina Diachenko

    The object of this research is the process of oscillation of liquid metallurgical slag in a slag bowl under the influence of acceleration. The work considers the oscillation processes in bowls used on railway and road slug cars, which differ in design and operating conditions. One of the key problems associated with the transportation of liquid slag is the dynamic instability of the melt, which leads to oscillations and splashing, which can pose a safety threat and reduce the efficiency of the transportation process. In this regard, the study of the dynamics of liquid slag in bowls of various designs is an urgent task aimed at optimizing transportation parameters and developing measures to reduce the risk of slag splashing. Based on the results of numerical modeling, it was established that the nature of the oscillations of liquid slag in the bowl significantly depends on the magnitude of the acceleration, the type of slag and the design of the bowl. In particular, the acceleration ranges at which different oscillation modes are observed, from minor surface disturbances to intensive slag splashing, have been determined. At the same time, the differences in the nature of oscillations for different types of slag and bowl designs lie within the limits determined by their physicochemical properties and geometric parameters. The results obtained allow to conclude that it is possible to develop measures for the operation of slag bowls, as well as their designs, in the direction of reducing the amplitude of liquid slag oscillations, which, in turn, contributes to increasing transportation safety and reducing dynamic loads on the bowl walls. The obtained data can be used in the design of new bowl designs to optimize their shape and internal elements in order to minimize slag oscillations. In addition, the information provided can be useful for metallurgical enterprises to develop effective methods for controlling and monitoring slag stability during transportation.

  • Assessing criteria for casting and deformation suitability of metals and alloys

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, V. F Mazorchuk, S. I Repyakh

    Purpose. Based on existing criteria for predicting the suitability of metals and their alloys for manufacturing products from them by deformation or casting analysis develop a set of dimensionless parametric criteria and their quantitative scales. Their using will allow increasing the predicting accuracy of metals and alloys for their processing by pressure or casting suitability and feasibility. Methodology. The work uses phenomenological approach to systematic analysis results of metals and alloys mechanical and individual casting properties interpreting under uncertainty conditions, drawing on literature reference data, expert evaluation data and the authors’ own research results. The authors’ own data have been obtained experimentally using standard methods for mechanical properties determining and due to original authors’ method for technical purity metals and alloys based on them cast samples values of their absolutely hindered linear shrinkage determination during casting. Findings. The authors first proposed parametric dimensionless criteria and scales to them (criteria groups). Their application allows one, through such groups combinations, to assess suitability of any alloy or metal for its use possibility for products manufacturing by casting and/or pressure processing. Originality. For the first time dimensionless parametric criteria have been developed and proposed for use at initial stages of new alloys or technologies elaboration for products from them manufacturing as well as their quantitative scales for preliminary assessment (prognosis) of alloys processing feasibility by pressure or casting, regardless of their type and method. Practical value. Developed criteria and their quantitative scales using will allow alloys developers and specialized enterprises employees to save time and expenses both for alloy elaboration and for its implementation into production.


  • Improving the Chemical Composition of High-Strength Special-Purpose Steels with the Formation of a Bainite Structure

    by Iron and Steel Institute of Z.I. Nekrasov of NAS of Ukraine, Olexander Babachenko, Ganna Kononenko, Tetyana Kimstach, Ukrainian State University of Science and Technologies, Rostyslav Podolskyi, Nstitute Of Applied Control Systems Of Nas Of Ukraine, Olena Safronova

    The work considers the improvement of the chemical composition of high-strength special-purpose steels in order to reduce the mass of products, the content of expensive alloying elements while increasing the level of mechanical properties. The main attention is paid to the alloying of steels of the Cr-Ni-Mo system using microalloying elements (V, Ti, Nb, B), which contributes to the formation of a homogeneous bainite structure after heat treatment. Four variants of experimental steels were manufactured in laboratory conditions, for which the chemical composition, microstructure and microhardness were studied. Metallographic analysis was carried out, the nature of the liquation, the morphology of bainite, the presence of retained austenite and other structural components were determined. It is shown that by changing the content of alloying elements, it is possible to controllably influence the structure and properties of steels. The results obtained can be used to develop new materials with improved performance characteristics for special-purpose products.

  • Influence of ice structure on vitability of frozen sand-water and sand-clay mixtures

    by L. I Solonenko, K. I Uzlov, T. V Kimstach, Ya. V Mianovska, D. Yu Yakymenko

    New+Solid State Physics, Mineral Processing +https://doi.org/10.33271/nvngu/2024-1 +/jdownloads/pdf/2024/1/01_2024_contents-en-GB.pdf