OBOleksandr Bilyi

Oleksandr Bilyi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleksandr Bilyi has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Identification of Effective Coefficients of Thermal Contraction of Structural States in Cast Bronze by Solving Inverse Problems of Thermodeformation Modeling

    by Tetiana Kimstach, Hennadii Shvachych, Kostiantyn Uzlov, Oleksandr Bilyi, Serhii Repiakh, Serhii Semenov, Magdalena Krupska-Klimczak

    The temperature-dependent formation of free linear shrinkage in cast CuAl7Si2Sn1.5Mn0.3 aluminum bronze was investigated using a cascade inverse-identification approach. Experimental data for 17 bronze compositions (Kᵣ = 0.41–0.85), including differential thermal analysis, quantitative metallography, and free-linear-shrinkage measurements, were used to reconstruct three genetic structure-formation pathways. Unlike conventional phase-averaging approaches, the proposed methodology identifies effective integral-average coefficients of linear thermal contraction (IA-CLTCs) of successive structural states directly from integral shrinkage data without requiring independently prescribed thermophysical properties of individual phases. The identified IA-CLTC sequences were 20.10 → 15.44 → 18.99 × 10−6 K−1 for pathway I, 21.88 → 29.40 → 11.57 × 10−6 K−1 for pathway II, and 25.90 → 36.65 → approximately 11.67 × 10−6 K−1 for pathway III. The first coefficient of pathway I was adopted as a fixed reference value. The model reproduced the experimental shrinkage with R2 = 0.998 and RMSE = 0.00562 percentage points. Conditional cascade leave-one-composition-out cross-validation yielded RMSE = 0.00995 percentage points, compared with 0.00915 percentage points for a simple linear-regression benchmark. Near the boundary between pathways II and III, the reconstructed thermal and structural-transformation contributions exhibited nearly compensating changes, although their quantitative separation remained model-dependent. Numerical sensitivity analysis revealed strong parameter correlation and limited practical identifiability for pathway III. The proposed approach therefore provides a framework for reconstructing effective temperature–deformation characteristics of successive structural states, while independent experimental validation remains necessary for their broader predictive and physical interpretation.

  • Phase composition of multicomponent aluminum bronzes criteria-based evaluation (Part 1. Supersaturated copper α-matrix and phase composition of Cu–Al–X system multicomponent bronzes stability criteria)

    by Т. V Kimstach, K. І Uzlov, G. G Shvachych, О. P Bilyi, S. I Repyakh

    Purpose. To establish structurally reliable and thermodynamically justified criteria for assessing alloys supersaturated copper α-matrix stability and predicting the phase composition of multicomponent bronzes formed under crystallization and subsequent cooling non-equilibrium conditions. Methodology. Methodology is based on thermodynamic analysis, structural-parametric approach and experimental data generalization combination. Copper matrix condition was estimated by parameter  (theoretically required and actual Cu content ratio). Thermodynamic analysis was performed within Gibbs energy minimization framework, taking into account small deviations and components with  activities connection. Structural and mechanical properties were evaluated using KR criterion. Findings. To assess in multicomponent bronzes single-phase state fixing or losing conditions, concentration parameter  has been proposed, which characterizes the conditions for solid solution non-equilibrium stability loss under casting conditions. It has been shown that at   1 conditions for secondary phase’s formation arise. KR criterion has been proposed to assess structural and mechanical properties. It has been proven that  and KR joint using provides “composition-stability-structure-properties” relationship for multicomponent aluminum bronzes comprehensive description. Originality. For the first time, quantitatively consistent system has been established of correlations between supersaturation parameter , compositional criterion KR and structural parameter  ‒ Cu–Al–Si–Mn–Sn system bronzes secondary phases volume fraction, which are formed under non-equilibrium conditions of solidification and in solid state subsequent cooling and are inherent in castings manufactured using foundry sand and metal molds. Practical value. Using indicator () and criterion (KR), proposed in the work, will allow increasing Cu–Al–Si–Mn–Sn system bronzes phase composition and properties predicting accuracy when changing their alloying elements concentrations. to reduce the time spent and resources during new alloys development or known bronze grades composition optimization by building regression and predictive models for managing their phase composition and properties. A parameter and criterion have been developed, along with an approach to creating new alloys and improving the existing alloys, their analysis, etc.

  • Open Access

    Regeneration and Alternative Utilization of Spent Sand-Sodium Silicate Mixtures Structured via Sodium Silicate Dehydration

    by L.I. Solonenko, S.I. Repyakh, О.P. Bilyi

    Relevance. The relevance of this work is driven by the urgent need to mitigate the environmental impact of spent foundry molding sands and to develop high-efficiency, low-energy, and resource-saving reclamation technologies. Results. It was established that the water resistance of sand-sodium silicate mixtures structured by dehydration exhibits an inversion-type dependence on the sodium silicate content and the duration of MW-structuring (microwave structuring). This behavior is attributed to the competitive processes between the formation and dehydration of silicate bridges (cuffs). It is shown that the structural degradation in water follows a diffusion-kinetic mechanism and is determined by temperature, water volume, and binder content. A generalized parameter ΘSMS, is proposed to synthesize the influence of composition and structuring regimes on the system's properties. It was found that strength, water resistance, and hydro-regeneration duration are described by monotonic exponential functions with asymptotic saturation relative to ΘSMS parameter. An analytical model for estimating the neutralizing agent consumption was developed with a margin of error within 10 %. The study demonstrates the feasibility of effective hydro-regeneration using limited water volumes and subsequent reuse of the mixture. Scientific Novelty. For the first time, a generalized dimensionless parameter ΘSMS has been introduced. This parameter integrates the sodium silicate dosage and its degree of dehydration, defining the structural state and the complex of properties of sand-sodium silicate mixtures structured by dehydration. A unified correlation between strength, water resistance, and hydro-regeneration duration via the ΘSMS parameter was established and interpreted as a percolation-type transi- tion within the intergranular silicate framework. Practical Significance. The findings allow for the optimization of MW-structuring and hydro-regeneration regimes for dehydration-structured sand-sodium silicate mixtures. This ensures a reduction in water, energy, and binder consumption while maintaining the required level of technological properties. Актуальність. Актуальність роботи обумовлена необхідністю зниження екологічного навантаження, зумовленого відпрацьованими формувальними сумішами ливарного виробництва, та розроблення високоефективних низькоенерговитратних ресурсозберігаючих технологій їх регенерації. Отримані результати. Встановлено, що водостійкість піщано-рідкоскляних сумішей, що структуровані за рахунок дегідратації, має інверсійний характер залежності від вмісту рідкого скла та тривалості ПМЗ-структурування, що обумовлено конкуренцією процесів формування та дегідратації силікатних манжет. Показано, що руйнування структури у воді має дифузійно-кінетичну природу і визначається температурою, об’ємом води та вмістом зв’язувального. Запропоновано параметр ΘПМЗ, який узагальнює вплив складу та режимів структурування на властивості системи. Встановлено, що міцність, водостійкість і тривалість гідрорегенерації описуються монотонними експоненційними залежностями з асимптотичним виходом на насичення від параметра ΘПМЗ. Отримано аналітичну модель для оцінки витрати нейтралізуючого реагенту з похибкою не більше 10 %. Показано можли- вість ефективної гідрорегенерації з обмеженим об’ємом води та повторного використання суміші. Наукова новизна. Вперше введено узагальнений безрозмірний параметр ΘПМЗ, який інтегрує кількість рідкого скла та ступінь його дегідратації і визначає структурний стан піщано-рідкоскляної суміші, що структурована за рахунок дегідратації, та комплекс її властивостей. Встановлено єдину закономірність взаємозв’язку між міцністю, водостійкістю та тривалістю гідрорегенерації через параметр ΘПМЗ, що інтерпретується як перколяційного типу перехід у структурі міжзеренного силікатного каркаса. Практичне значення. Отримані результати дозволяють оптимізувати режими ПМЗ-структурування і гідрорегенерації піщано-рідкоскляних сумішей, що структуровані за рахунок дегідратації, забезпечуючи зниження витрат води, енергії та зв’язувального при збереженні рівнів необхідних їм технологічних властивостей.

  • Mechanical properties and structure of Cu-Al-Si-Sn-Mn system non-magnetic cast bronzes

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, S. I Repyakh

    Purpose. To establish regularity of Cu-Al-Si-Sn-Mn system non-magnetic corrosion-resistant bronze chemical composition on structure and mechanical properties complex influence and to determine its rational composition in terms of suitability for manufacturing products by casting methods. Methodology. For bronzes mechanical properties determination FP-100/1 technique and PSW-30 pendulum machine are used. Neophot-21 microscope is used to study microstructures. Chemical elements ratio in local areas of structural components determination is carried out with SEM-515 microanalyzer. Bronzes fracture surfaces fractographic analysis is performed visually and using Coxem EM-40 electron microscope. Bronzes relative magnetic permeability is measured with Magnetomat 1.790 magnetometer. Alloys chemical composition is determined using EXPERT 4L analyzer. Findings. It has been established that Cu-Al-Si-Sn-Mn system bronze suitable for casting in sand molds should contain by weight 6.0‒7.5 % Al, 1.0‒2.5 % Si, 0.21‒0.45 % Mn and 1.0‒2.2 % Sn, and alloying chemical elements ratio and inevitable impurities, according to the formula: KR = (1‒0.01 nn) (Al-Si-Mn)/(1 + Sn)2, should be equal to 0.42‒0.85. Bronze with KR > 0.85 is low-strength, but ductile and, therefore, mainly suitable for manufacturing products from it by deformation methods. Bronze with KR < 0.42 is low-strength and brittle and it is not suitable for manufacturing products by either casting or deformation methods. Originality. For the first time, Cu-Al-Si-Sn-Mn system bronzes alloying elements complex influence on their mechanical properties and structure formation features has been determined. Cu-Al-Si-Sn-Mn system aluminum bronzes with KR value from 0.42 to 0.85 mechanical properties levels increase with Cu-solid solution relative volume fraction in their structures decreasing, that is, with KR value increasing. Practical value. The data obtained can be used as a basis for new casting, corrosion-resistant non-magnetic bronzes development that have strength and density at the level of carbon steels or aluminum bronzes alloyed with nickel and iron.


  • Determination of bronze БрА7К2О1,5Мц0,3 crystallization interval limit values and phase transformations

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, L. I Solonenko, S. I Repyakh

    Phase transformations temperatures, crystallization intervals, etc. are any alloy’s fundamental parameters. Alloys’ casting, technological and operational properties are related to them. Nevertheless, unlike two-component bronzes, such requirements for multi-component structural, non-magnetic, corrosion-resistant bronze БрА7К2О1,5Мц0,3 are absent. Purpose. For Cu-Al-Si-Sn-Mn system bronzes, crystallization intervals quantitative values (liquidus and solidus temperatures, crystallization interval size and solid phase relative share in it) have been established. БрА7К2О1,5Мц0,3 bronze’s alloying components’ synergistic and selective influence on its crystallization interval and relative fluidity indicators changing has been determined. Methodology. Well-known methods and research techniques, including thermography, differential thermal analysis, spectral chemical analysis, images analysis digital method have been used in this work. Bronzes fluidity has been assessed using spiral test. Bronze’s alloying elements’ synergistic and selective influences on its characteristics have been determined using chemical elements ratio in it (KR criterion) and experimental data results processing by Excel computer program. Findings. In bronze БрА7К2О1,5Мц0,3 with KR criterion value rising from 0.35 to 0.84, there increase liquidus, solidus temperatures and crystallization interval from 32 to 49 °C. Bronze’s alloying elements’ (Al, Si, Sn, Mn) synergistic and selective influences on its crystallization interval limit values have been determined. It has been established that conditionally-veritable fluidities of БрА7К3О1,5Мц0,3 and БрА9Ж3Л bronzes are practically the same. For Cu-Al-Si-Sn-Mn system bronzes with KR = 0.35‒2.07, solid phase relative volume fraction (SP) in crystallization temperature range is 60‒63 %. Originality. For the first time, limiting values and phase transformations for БрА7К2О1,5Мц0,3 bronze’s crystallization interval and alloying elements synergistic and selective influence on these indicators have been determined. Practical value. Based on БрА7К2О1,5Мц0,3 bronze’s chemical composition selected, mathematical models have been proposed for its liquidus and solidus temperatures calculating and for transition from dependences of solid phase t(SP) volume fraction in crystallization temperature range to temperatures’ absolute values t(SP). Their use will allow increasing the indicators of foundry and technological parameters accuracy forecasting.


  • Si and Mn effect on mechanical properties and linear shrinking of non-magnetic Cu-Al system cast bronzes

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, S. I Repyakh

    Purpose. To establish Si and Mn influence on mechanical properties level at 20 °C and aluminum bronzes structure with Al from 3 to 9 % mass content investigation. Methodology. Cast bronzes mechanical properties have been determined based on their fracture results on FP-100/1 machine and PSW-30 pendulum impactor. Microstructure has been examined using Neophot-21 optical microscope. Bronzes linear shrinkage coefficients have been calculated based on results of determining cast cylindrical samples lengths changes. Si and Mn complex influence on bronzes properties has been determined by the results of simplex triangles according to H. Scheffer plan constructing. Temperature has been measured with chromel-alumel thermocouple completed with electronic potentiometer. Bronzes chemical composition has been determined on ­EXPERT 4L analyzer. Findings. Silicon (up to 2 %) and manganese (up to 2 %) adding to Cu-Al system bronze, while aluminum content from 9 to 3 % reducing, leads to bronze ultimate tensile and yield strength decreasing during stretching and its plasticity increasing. At the same time, bronze structure, at any combination of Al, Si and Mn contents within their changes in studied limits, remains single-phase. Originality. For the first time, comprehensive assessment of influence of Si and Mn with simultaneous decrease in Al content on mechanical properties and linear shrinkage of Cu-Al-Si-Mn system cast bronzes has been carried out. It has been established that all bronzes of studied compositions have a single-phase structure and mechanical properties level that is inherent for pressure-worked bronzes. Practical value. The research results expand understanding about elemental and complex influence of Si and Mn on aluminum bronzes properties, provide an opportunity to choose a bronze with properties required level from its cast billet for deformation or to design castings taking into account the linear shrinkage values discovered in this work. The data obtained can also be the basis for new foundry, corrosion-resistant, non-magnetic bronzes, which have strength and density at the level of some carbon steel grades, development. Such materials have been used for parts that operate in chemically aggressive environments manufacturing, for control and measuring equipment and devices parts, for ship parts and naval devices, fittings, bushings, couplings, intrinsically safe tools, etc.


  • Assessing criteria for casting and deformation suitability of metals and alloys

    by T. V Kimstach, K. I Uzlov, O. P Bilyi, V. F Mazorchuk, S. I Repyakh

    Purpose. Based on existing criteria for predicting the suitability of metals and their alloys for manufacturing products from them by deformation or casting analysis develop a set of dimensionless parametric criteria and their quantitative scales. Their using will allow increasing the predicting accuracy of metals and alloys for their processing by pressure or casting suitability and feasibility. Methodology. The work uses phenomenological approach to systematic analysis results of metals and alloys mechanical and individual casting properties interpreting under uncertainty conditions, drawing on literature reference data, expert evaluation data and the authors’ own research results. The authors’ own data have been obtained experimentally using standard methods for mechanical properties determining and due to original authors’ method for technical purity metals and alloys based on them cast samples values of their absolutely hindered linear shrinkage determination during casting. Findings. The authors first proposed parametric dimensionless criteria and scales to them (criteria groups). Their application allows one, through such groups combinations, to assess suitability of any alloy or metal for its use possibility for products manufacturing by casting and/or pressure processing. Originality. For the first time dimensionless parametric criteria have been developed and proposed for use at initial stages of new alloys or technologies elaboration for products from them manufacturing as well as their quantitative scales for preliminary assessment (prognosis) of alloys processing feasibility by pressure or casting, regardless of their type and method. Practical value. Developed criteria and their quantitative scales using will allow alloys developers and specialized enterprises employees to save time and expenses both for alloy elaboration and for its implementation into production.


  • Technogenic hazards coefficient of sand-resin mixtures in foundry manufacturing

    by L. I Solonenko, K. I Uzlov, S. I Repiakh, I. V Prokopovich, O. Р Bilyi

    Purpose. To carry out a comparative quantitative assessment of environmental and sanitary-hygienic hazards of utilizing synthetic resins for manufacturing molds and rods in foundry production. Methodology. Quarry quartz sand brand 1K2O202, furan resin brand Permaset 839 and catalyst Permacat 128, aluminum alloy AL2, gray cast iron SCh200, carbon steel 30L, bronze BrА9Zh3L were used in the work. Chromel-alumel thermocouples completed with electronic potentiometer were used for thermography. Molds were made from quartz sand, furan resin and catalyst mixture. Casting mold heating depth determination from casting to temperatures above 400 °C was carried out by its thermogram graphical processing, which was obtained after casting mold pouring with aluminum alloy, bronze, gray cast iron and carbon steel. Findings. Among those studied, the most dangerous are urea-phenol-formaldehyde, urea-formaldehyde and urea-furan resins, and the least dangerous are phenol-formaldehyde and phenol-formaldehyde-furan resins. Ecological and sanitary-hygienic hazard level when using resin mixtures increases with increasing resin amount in mixture, castings walls thickness, their surface area, as well as with increasing temperature of melt poured into the mold. Originality. For the first time, in relation to foundry molds and rods in foundry production manufacturing, technogenic hazard coefficient (THC) has been developed and its value has been calculated. This, in fact, is air volume (m3) containing maximum permissible concentration of carcinogenic or poisonous substances released as a result of mold organic binder material destruction when pouring aluminum alloy, bronze, cast iron or steel. Practical value. The use of the research results makes it possible to increase the level of predicting accuracy of technogenic (sanitary, hygienic and environmental) hazards, accuracy level of calculating ventilation systems capacities in foundries, taking into account the serial castings production, castings structural features, as well as binding materials nature for foundry molds and rods for such castings.

  • Water gas saturation as a lever for controlling the level of properties of frozen foundry molds

    by L.I. Solonenko, S.I. Rep’yakh, M.I. Zamyatin, O.P. Bilyi, І.A. Kostenko, С.і. Реп’ях, М.і. Замятін

    The purpose of the work is to increase the survivability of sand-clay forms that freeze in equipment without the use of liquefied gases. Quartz sand 1K3O3016, bentonite clay BS2T2, kaolin clay KS2T2, tap water, carbonated water and degassed (boiled) water were used in the research. Flowability was determined according to GOST 23409.9, compressive strength — GOST 23409.7, gas permeability — GOST 29234.11. In order to achieve the specified level of the main parameters of sand-clay mixtures frozen at –15 °С with a simultaneous increase in the survivability of frozen casting molds and rods up to ~18 min, it is most appropriate to use a mixture of 5 % bentonite clay of the BS2T2 brand and 5 % of degassed (boiled) water with clay activation in such water as part of the mixture for 24 hours. At the same time, the use of KS2T2 kaolin clay as part of mixtures is impractical, since mixtures with such clay do not meet the requirements for molding and core mixtures. Molding mixtures consisting exclusively of sand and water are not suitable for the production of casting molds and rods due to high flowability. To increase the strength and reduce the flowability, it is necessary to use a mixture of sand, water and clay for the production of frozen molds and rods. Addition of bentonite (BS2T2) or kaolin (КS2Т2) clay to sand and water leads to a decrease in the flowability of frozen mixtures and an increase in their strength. Frozen at –15 °C mixtures with a kaolin clay content of up to 7 % (by mass) and 5 % (by mass) of tap water are characterized by increased flowability, which makes it impossible to use them as a molding or core mixture. When adding 5 % of bentonite clay BS2T2 swollen with degassed water to quartz sand, the flowability of the frozen mixture becomes less than 0.1 %, the gas permeability reaches 129 units, and the compressive strength exceeds 4.0 MPa, which meets the requirements for molding and rod mixtures. The gas saturation of water is a powerful lever in the system of controlling the level of properties of frozen casting molds, which include quartz sand and swollen bentonite clay.

  • Open Access

    Influence of sand-sodium-silicate mixtures structured by steam-microwave solidification method on small castings quality

    by Ukraine) National Metallurgical Academy Of Ukraine (Dnipro, L.I. Solonenko, S.I. Repyakh, K.і. Uzlov, О.P. Bilyi

    Influence of sand-sodium-silicate mixtures structured by steam-microwave solidification method on small castings quality