Mason Ghafghazi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mason Ghafghazi has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Jason T. DeJong
University of California
6 shared publications - Alexander P. Sturm
Graduate Student, Dept. of Civil and Environmental Engineering, Univ. of California, Davis, One Shields Ave., Davis, CA 95616
3 shared publications - Kevin C. Kuei
Univ. of California at Davis
3 shared publications Mathan V. Manmatharajan
Univ. of Toronto
3 shared publicationsWei Liu
Univ. of Toronto
3 shared publicationsAlex Sy
ASy Consulting, Inc
2 shared publications
Latest Publications
- 1 January 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 153 (1) , 04026153
Three-Dimensional Numerical Modeling of Drained Uplift Behavior of Rectangular Plate Anchors Using NorSand
Plate anchors offer an attractive anchoring solution for floating renewable energy devices in deep water, whereas the uplift behavior of plate anchors in sand and the associated failure mechanisms remain insufficiently explored. This study investigates the uplift behavior and the corresponding three-dimensional (3D) failure mechanisms of rectangular plate anchors in sand through finite element (FE) analysis. The critical state–based NorSand model, implemented in the FE package Abaqus/Standard, was employed to describe sand behavior. The FE model was validated against both element tests and centrifuge data. A parametric study was conducted to investigate the effects of relative density and embedment ratio on the uplift capacity of rectangular anchors in sand. The 3D failure mechanism of rectangular anchors in sand was revealed and discussed, with particular focus on the inclination angles of shear bands and the extent of the failure zone, which provide key parameters for improving the predictive capability of existing analytical solutions. Stress paths at representative positions within the failure zone were examined, revealing a progressive failure mechanism that is analogous to triaxial compression and simple shear loading modes. Based on the simulation results, the shape factor predictions for rectangular anchors were discussed, showing the conservatism (i.e., underestimation) of existing methods in medium-dense sand. Practical relations were further developed to provide FE-based shape factor estimates for the rectangular anchors investigated. The findings highlight the importance of considering the 3D failure mechanism in plate anchor design.
- 1 January 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 153 (1) , 04026153
Three-Dimensional Numerical Modeling of Drained Uplift Behavior of Rectangular Plate Anchors Using NorSand
Plate anchors offer an attractive anchoring solution for floating renewable energy devices in deep water, whereas the uplift behavior of plate anchors in sand and the associated failure mechanisms remain insufficiently explored. This study investigates the uplift behavior and the corresponding three-dimensional (3D) failure mechanisms of rectangular plate anchors in sand through finite element (FE) analysis. The critical state–based NorSand model, implemented in the FE package Abaqus/Standard, was employed to describe sand behavior. The FE model was validated against both element tests and centrifuge data. A parametric study was conducted to investigate the effects of relative density and embedment ratio on the uplift capacity of rectangular anchors in sand. The 3D failure mechanism of rectangular anchors in sand was revealed and discussed, with particular focus on the inclination angles of shear bands and the extent of the failure zone, which provide key parameters for improving the predictive capability of existing analytical solutions. Stress paths at representative positions within the failure zone were examined, revealing a progressive failure mechanism that is analogous to triaxial compression and simple shear loading modes. Based on the simulation results, the shape factor predictions for rectangular anchors were discussed, showing the conservatism (i.e., underestimation) of existing methods in medium-dense sand. Practical relations were further developed to provide FE-based shape factor estimates for the rectangular anchors investigated. The findings highlight the importance of considering the 3D failure mechanism in plate anchor design.
- 1 December 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 152 (12) , 04026125
Impact of Compliance on Constant-Height Simple Shear Tests
Simple shear testing is an important laboratory tool in geotechnical engineering, providing insights into soil behavior under conditions relevant to landslides, foundation instability, and earthquake loading. Undrained conditions are often reproduced by imposing constant volume in simple shear tests, where maintaining constant height is essential. However, compliance stemming from deformations in device components can seriously affect results, often causing overestimation of strength. This study quantifies compliance in simple shear equipment and evaluates its impact on monotonic and cyclic tests. It demonstrates that measured vertical strain (nominal compliance) often meets the ASTM standard ( ± 0.05 % of the specimen’s pre-shear height), while actual compliance, which represents the specimen’s actual vertical strain, can easily exceed the ASTM threshold. The consequence for monotonic tests is a subdued response, manifested as less contraction in contractive specimens and less dilation in dilative specimens, resulting in lower peaks and higher troughs in the measured shear stress. A height correction feedback loop was implemented to correct compliance errors in cyclic tests to eliminate the difference between nominal and actual compliance. The findings indicate that compliance delays liquefaction and causes the cyclic resistance ratio to be overestimated. These observations highlight the need to improve compliance control in commercially available simple shear equipment and to improve how constant-height control is evaluated and reported. A stress-based criterion is proposed to replace the current ASTM approach.
- 1 December 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 152 (12) , 04026125
Impact of Compliance on Constant-Height Simple Shear Tests
Simple shear testing is an important laboratory tool in geotechnical engineering, providing insights into soil behavior under conditions relevant to landslides, foundation instability, and earthquake loading. Undrained conditions are often reproduced by imposing constant volume in simple shear tests, where maintaining constant height is essential. However, compliance stemming from deformations in device components can seriously affect results, often causing overestimation of strength. This study quantifies compliance in simple shear equipment and evaluates its impact on monotonic and cyclic tests. It demonstrates that measured vertical strain (nominal compliance) often meets the ASTM standard ( ± 0.05 % of the specimen’s pre-shear height), while actual compliance, which represents the specimen’s actual vertical strain, can easily exceed the ASTM threshold. The consequence for monotonic tests is a subdued response, manifested as less contraction in contractive specimens and less dilation in dilative specimens, resulting in lower peaks and higher troughs in the measured shear stress. A height correction feedback loop was implemented to correct compliance errors in cyclic tests to eliminate the difference between nominal and actual compliance. The findings indicate that compliance delays liquefaction and causes the cyclic resistance ratio to be overestimated. These observations highlight the need to improve compliance control in commercially available simple shear equipment and to improve how constant-height control is evaluated and reported. A stress-based criterion is proposed to replace the current ASTM approach.
- Open Access
- 5 December 2025
- Published by Atlantis Press SARL
- p. 359-367
Assessment of NorSand’s Performance under Zero Strain Boundary Conditions
- 5 December 2025
- Published by Atlantis Press SARL
- p. 359-367
Open AccessAssessment of NorSand’s Performance under Zero Strain Boundary Conditions
- 1 December 2024
- Published by Emerald Publishing in Geotechnical Research
- Vol. 11 (4) , 226-242
Evaluation of state parameter interpretation methods using CPT calibration chamber data
The cone penetration test (CPT) is widely used to determine the in situ state parameter of soils because it provides continuous data and excellent repeatability at a relatively low cost. Accurate interpretation of the state parameter from CPT is the basis for evaluating the strength of granular soils, including assessing liquefaction susceptibility in important structures such as tailings storage facilities. A few interpretation methods are used in practice. They use two different overburden stress normalisation schemes on tip resistance. These methods vary in how much information they utilise to differentiate among soils. This paper evaluates these methods by applying them to an extensive database of calibration chamber tests. Then, the state parameter interpreted by each method is compared with that determined from laboratory data. The database includes manufactured sands, natural sands, and clean sand tailings. The soils were selected such that both calibration chamber testing and triaxial compression data were available from the literature. This evaluation serves as a minimum requirement for applying these methods in engineering projects, especially those dealing with challenging soils such as fines-rich tailings. This study suggests that methods that account for soil properties and in situ horizontal stresses perform better than those that do not.
- 1 December 2024
- Published by Emerald Publishing in Geotechnical Research
- Vol. 11 (4) , 226-242
Evaluation of state parameter interpretation methods using CPT calibration chamber data
The cone penetration test (CPT) is widely used to determine the in situ state parameter of soils because it provides continuous data and excellent repeatability at a relatively low cost. Accurate interpretation of the state parameter from CPT is the basis for evaluating the strength of granular soils, including assessing liquefaction susceptibility in important structures such as tailings storage facilities. A few interpretation methods are used in practice. They use two different overburden stress normalisation schemes on tip resistance. These methods vary in how much information they utilise to differentiate among soils. This paper evaluates these methods by applying them to an extensive database of calibration chamber tests. Then, the state parameter interpreted by each method is compared with that determined from laboratory data. The database includes manufactured sands, natural sands, and clean sand tailings. The soils were selected such that both calibration chamber testing and triaxial compression data were available from the literature. This evaluation serves as a minimum requirement for applying these methods in engineering projects, especially those dealing with challenging soils such as fines-rich tailings. This study suggests that methods that account for soil properties and in situ horizontal stresses perform better than those that do not.
- 1 December 2024
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 61 (12) , 2858-2872
Material-specific interpretation of the state parameter from drained cone penetration test
The Cone Penetration Test (CPT) is a widely used site investigation tool due to its accuracy and wealth of data at a relatively low cost. Virtually all CPT interpretations explicitly or implicitly depend on how the in-situ state parameter is correlated to the tip resistance. Accurate interpretation of the state parameter from CPT is the basis for evaluating strength and liquefaction susceptibility of granular soils. The handful of interpretation methods used in the industry range between empirical and semi-empirical. As is the case for all empirical methods, extrapolating these methods outside of the original database, especially to significantly different soils such as silt-rich tailings, brings about significant risk. This paper presents a new method of interpreting the state parameter from a fully validated model of the cone penetration in sand. The method has no empirical elements and produces soil-specific correlations between the tip resistance and the state parameter. It can be easily implemented in a spreadsheet and does not require complicated analyses. The method differentiates among soils through calibration of a critical state based constitutive model, Norsand, through triaxial compression tests. The potential errors induced by not measuring soil properties are quantified.
- 1 December 2024
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 61 (12) , 2858-2872
Material-specific interpretation of the state parameter from drained cone penetration test
The Cone Penetration Test (CPT) is a widely used site investigation tool due to its accuracy and wealth of data at a relatively low cost. Virtually all CPT interpretations explicitly or implicitly depend on how the in-situ state parameter is correlated to the tip resistance. Accurate interpretation of the state parameter from CPT is the basis for evaluating strength and liquefaction susceptibility of granular soils. The handful of interpretation methods used in the industry range between empirical and semi-empirical. As is the case for all empirical methods, extrapolating these methods outside of the original database, especially to significantly different soils such as silt-rich tailings, brings about significant risk. This paper presents a new method of interpreting the state parameter from a fully validated model of the cone penetration in sand. The method has no empirical elements and produces soil-specific correlations between the tip resistance and the state parameter. It can be easily implemented in a spreadsheet and does not require complicated analyses. The method differentiates among soils through calibration of a critical state based constitutive model, Norsand, through triaxial compression tests. The potential errors induced by not measuring soil properties are quantified.
- 1 May 2024
- Published by Emerald Publishing in Géotechnique
- Vol. 74 (5) , 499-510
The full state of stress in monotonic simple shear tests on sand
The simple shear test has been an important tool in practical geotechnical engineering and the study of soil behaviour. The attractiveness of the simple shear test is founded in its relative ease of specimen preparation, similarity to at-rest conditions during consolidation and rotation of principal stresses during shear. Despite this test's attractive qualities, there are significant deficiencies in the interpretation of standard test results: horizontal normal stresses are not known and excess pore pressures are often interpreted from assumptions about constant-volume tests without saturation. To address this problem, a set of monotonic tests were performed on a sand, during which horizontal normal stresses were measured in the central portion of specimens. Based on the measurements, the full state of stress was defined, stress paths were drawn and directions of the principal stresses were determined. Outcomes showed that the conventional approach of estimating excess pore pressures as the change in vertical pressure to maintain constant volume in response to shear is problematic, and friction angles interpreted from conventionally measured shear and vertical stresses may be grossly underestimated in some cases.
- 1 May 2024
- Published by Emerald Publishing in Géotechnique
- Vol. 74 (5) , 499-510
The full state of stress in monotonic simple shear tests on sand
The simple shear test has been an important tool in practical geotechnical engineering and the study of soil behaviour. The attractiveness of the simple shear test is founded in its relative ease of specimen preparation, similarity to at-rest conditions during consolidation and rotation of principal stresses during shear. Despite this test's attractive qualities, there are significant deficiencies in the interpretation of standard test results: horizontal normal stresses are not known and excess pore pressures are often interpreted from assumptions about constant-volume tests without saturation. To address this problem, a set of monotonic tests were performed on a sand, during which horizontal normal stresses were measured in the central portion of specimens. Based on the measurements, the full state of stress was defined, stress paths were drawn and directions of the principal stresses were determined. Outcomes showed that the conventional approach of estimating excess pore pressures as the change in vertical pressure to maintain constant volume in response to shear is problematic, and friction angles interpreted from conventionally measured shear and vertical stresses may be grossly underestimated in some cases.
- 1 August 2023
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 60 (8) , 1117-1131
Effect of particle size and particle size distribution on critical state loci of granular soils
The critical state soil mechanics captures a wide range of stress–strain behaviour in an understandable context. It provides a conceptual framework for predicting soil behaviour and that is why the critical state is a central part of most advanced constitutive models. This study aims at quantifying the effects of both particle size, and particle size distribution on the critical state loci. Two soils, a natural soil and a tailings, were selected and CSLs were identified for twelve uniform and well graded particle size distributions. Mineralogy and particle shapes were rigorously quantified to ensure other factors are not influencing the results. Particle size has a small influence on the CSL in the sand to gravel range, but silts can have a significantly different CSL. In both natural soil and tailings, particle size distribution appears to have a significant influence on the CSL in e − log p′space and little influence in q − p′ space. Well graded soils have lower CSLs compared to uniform ones, that are generally parallel to the CSLs of their dominant constituent, with the exception of convex distributions where progressively finer particles in larger proportions can form structures noticeably less compressible than any of their constituents.
- 1 August 2023
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 60 (8) , 1117-1131
Effect of particle size and particle size distribution on critical state loci of granular soils
The critical state soil mechanics captures a wide range of stress–strain behaviour in an understandable context. It provides a conceptual framework for predicting soil behaviour and that is why the critical state is a central part of most advanced constitutive models. This study aims at quantifying the effects of both particle size, and particle size distribution on the critical state loci. Two soils, a natural soil and a tailings, were selected and CSLs were identified for twelve uniform and well graded particle size distributions. Mineralogy and particle shapes were rigorously quantified to ensure other factors are not influencing the results. Particle size has a small influence on the CSL in the sand to gravel range, but silts can have a significantly different CSL. In both natural soil and tailings, particle size distribution appears to have a significant influence on the CSL in e − log p′space and little influence in q − p′ space. Well graded soils have lower CSLs compared to uniform ones, that are generally parallel to the CSLs of their dominant constituent, with the exception of convex distributions where progressively finer particles in larger proportions can form structures noticeably less compressible than any of their constituents.