Stanislav Horielyshev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Stanislav Horielyshev has a total of 136 co-authors. Here are the top co-authors by number of shared publications:
- Mykhailo Ivanets
State Scientific Research Institute of Armament and Military Equipment Testing and Certification
15 shared publications - Hryhorii Ivanets
Ivan Kozhedub Kharkiv National Air Force University
13 shared publications - Dmitro Baulin
National Academy of the National Guard of Ukraine
12 shared publications National Academy Of The National Guard Of Ukraine
10 shared publicationsСтаніслав Горєлишев
кандидат технічних наук, доцент, Національна академія Національної гвардії України, провідний науковий співробітник науково-дослідної лабораторії забезпечення службово-бойової діяльності Національної гвардії України інституту логістики; м. Харків, Україна
10 shared publications- Igor Boikov
National Academy of the National Guard of Ukraine
9 shared publications
Latest Publications
- Open Access
- 30 October 2026
- Published by National Academy of the National Guard of Ukraine in The Scientific Journal of the National Academy of National Guard "Honor and Law"
- Vol. 98 (3) , 95-102
Employment of unmanned aerial systems by units of the National Guard of Ukraine during the protection and defence of important state facilities
The place and role of unmanned aerial systems as an aerial component of a multi-level protection and defence system for important state facilities have been determined. The employment of unmanned aerial systems in the protection and defence of important state facilities is carried out under conditions of strictly regulated airspace and limited response time. The methods (airspace patrolling, airborne standby over critical directions, route-and-manoeuvre employment, and the "on-call" method) and the specific features of employing unmanned aerial systems by units of the National Guard of Ukraine under conditions of increasing threats have been substantiated. A response algorithm for protection units employing unmanned aerial systems has been developed in the form of a closed adaptive control cycle.
- 30 October 2026
- Published by National Academy of the National Guard of Ukraine in The Scientific Journal of the National Academy of National Guard "Honor and Law"
- Vol. 98 (3) , 95-102
Open AccessEmployment of unmanned aerial systems by units of the National Guard of Ukraine during the protection and defence of important state facilities
The place and role of unmanned aerial systems as an aerial component of a multi-level protection and defence system for important state facilities have been determined. The employment of unmanned aerial systems in the protection and defence of important state facilities is carried out under conditions of strictly regulated airspace and limited response time. The methods (airspace patrolling, airborne standby over critical directions, route-and-manoeuvre employment, and the "on-call" method) and the specific features of employing unmanned aerial systems by units of the National Guard of Ukraine under conditions of increasing threats have been substantiated. A response algorithm for protection units employing unmanned aerial systems has been developed in the form of a closed adaptive control cycle.
- Open Access
- 3 September 2026
- Published by National Academy of the National Guard of Ukraine in The collection of scientific works of the National Academy of the National Guard of Ukraine
- Vol. 47 (1) , 59-68
Study of the effectiveness of engaging «Shahed-136» kamikaze drones with the «Gepard 1А2» self-propelled anti-aircraft gun
Проведене у статті дослідження ураження дронів-камікадзе «Shahed-136» зенітною самохідною артилерійською установкою «Gepard 1A2» показало, що кількість черг снарядів, висота, дальність обстрілу та параметри польоту безпілотного літального апарата суттєво впливають на ймовірність ураження. Ймовірність ураження ударних дронів-камікадзе зенітною самохідною артилерійською установкою є основною узагальненою характеристикою її бойових можливостей щодо протидії подібним повітряним цілям. Вона залежить як від досяжності стрільби по висоті та дальності, так і від значення курсового параметра польоту безпілотника. Найефективніше застосовувати зенітну самохідну артилерійську установку «Gepard 1A2» для обстрілювання дронів-камікадзе типу «Shahed-136» трьома чергами на висоті до 1,5 км та дальності до 2 км,курсовий параметр польоту яких не перевищує 1000 м.
- 3 September 2026
- Published by National Academy of the National Guard of Ukraine in The collection of scientific works of the National Academy of the National Guard of Ukraine
- Vol. 47 (1) , 59-68
Open AccessStudy of the effectiveness of engaging «Shahed-136» kamikaze drones with the «Gepard 1А2» self-propelled anti-aircraft gun
Проведене у статті дослідження ураження дронів-камікадзе «Shahed-136» зенітною самохідною артилерійською установкою «Gepard 1A2» показало, що кількість черг снарядів, висота, дальність обстрілу та параметри польоту безпілотного літального апарата суттєво впливають на ймовірність ураження. Ймовірність ураження ударних дронів-камікадзе зенітною самохідною артилерійською установкою є основною узагальненою характеристикою її бойових можливостей щодо протидії подібним повітряним цілям. Вона залежить як від досяжності стрільби по висоті та дальності, так і від значення курсового параметра польоту безпілотника. Найефективніше застосовувати зенітну самохідну артилерійську установку «Gepard 1A2» для обстрілювання дронів-камікадзе типу «Shahed-136» трьома чергами на висоті до 1,5 км та дальності до 2 км,курсовий параметр польоту яких не перевищує 1000 м.
- Open Access
- 30 August 2026
- Published by National Academy of the National Guard of Ukraine in The Scientific Journal of the National Academy of National Guard "Honor and Law"
- Vol. 97 (2) , 103-111
Mathematical model of involvement of additional forces and resources of the National Guard of Ukraine to increase the reliability of the defense of nuclear installations
A mathematical model of involving additional forces and means of military units of the National Guard of Ukraine to increase the reliability of the defense of nuclear installations in conditions of armed aggression has been developed. The model is based on the established dependence between the combat potential of reserve units, the distances of their advancement to defense objects and the maximum response time, which is determined by the enemy's rate of advance. The process of regrouping reserves is formalized in the form of a multi-criteria transport problem, in which the variables are the volumes of the involved combat potential, and the optimization criteria are the minimization of a generalized indicator that takes into account transportation costs, the time of regrouping and the risk of loss of combat capability by reserves. The proposed approach takes into account the logistical costs of moving reserves and the predicted time of reaching the object by the enemy. It was established that the results obtained make it possible to substantiate rational options for distributing reserves of operational-territorial formations of the National Guard of Ukraine between military units for the protection of nuclear power plants and are intended for use by military command bodies when planning measures to strengthen the defense of nuclear installations.
- 30 August 2026
- Published by National Academy of the National Guard of Ukraine in The Scientific Journal of the National Academy of National Guard "Honor and Law"
- Vol. 97 (2) , 103-111
Open AccessMathematical model of involvement of additional forces and resources of the National Guard of Ukraine to increase the reliability of the defense of nuclear installations
A mathematical model of involving additional forces and means of military units of the National Guard of Ukraine to increase the reliability of the defense of nuclear installations in conditions of armed aggression has been developed. The model is based on the established dependence between the combat potential of reserve units, the distances of their advancement to defense objects and the maximum response time, which is determined by the enemy's rate of advance. The process of regrouping reserves is formalized in the form of a multi-criteria transport problem, in which the variables are the volumes of the involved combat potential, and the optimization criteria are the minimization of a generalized indicator that takes into account transportation costs, the time of regrouping and the risk of loss of combat capability by reserves. The proposed approach takes into account the logistical costs of moving reserves and the predicted time of reaching the object by the enemy. It was established that the results obtained make it possible to substantiate rational options for distributing reserves of operational-territorial formations of the National Guard of Ukraine between military units for the protection of nuclear power plants and are intended for use by military command bodies when planning measures to strengthen the defense of nuclear installations.
- Open Access
- 22 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
- No. 2,p. 51-58
IMPROVEMENT OF THE METHODOLOGICAL APPROACH TO ASSESSING THE EFFECTIVENESS OF THE ORGANISATION OF OPERATION OF AIR DEFENCE WEAPON AND MILITARY EQUIPMENT SYSTEMS OF THE GROUND FORCES
The experience of modern warfare has shown that the principal direction of the employment of air attack means is the integrated use of cruise and ballistic missiles, unmanned aerial vehicles of various types in delivering massed strikes against critical infrastructure facilities of the country, as well as the conduct of intensive air strikes to provide air support to ground force groupings during their offensive operations. Under such conditions, air defence, in particular the air defence of the Ground Forces, has become one of the primary strategic factors determining the level of national security, and in the course of combat operations substantially influences the outcomes of an armed conflict or war. Maintaining the air defence weapon systems of the Ground Forces in a constant state of readiness for employment in their intended role is ensured by the precise and high-quality implementation of measures for organising their operation. The article proposes an improved methodology for assessing the effectiveness of the organisation of operation of air defence weapon systems of the Ground Forces. As the criterion of effectiveness of the organisation of weapon operation, the requirement is adopted that the readiness coefficient for employment in the intended role shall be no worse than the specified value, that the time for bringing to readiness, deployment and redeployment, operational maintainability, and operational safety meet the established requirements given the available resource margin. This approach allows a more objective assessment of the effectiveness of the organisation of weapon operation for the purpose of making the necessary decisions to improve the situation where required
- 22 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
- No. 2,p. 51-58
Open AccessIMPROVEMENT OF THE METHODOLOGICAL APPROACH TO ASSESSING THE EFFECTIVENESS OF THE ORGANISATION OF OPERATION OF AIR DEFENCE WEAPON AND MILITARY EQUIPMENT SYSTEMS OF THE GROUND FORCES
The experience of modern warfare has shown that the principal direction of the employment of air attack means is the integrated use of cruise and ballistic missiles, unmanned aerial vehicles of various types in delivering massed strikes against critical infrastructure facilities of the country, as well as the conduct of intensive air strikes to provide air support to ground force groupings during their offensive operations. Under such conditions, air defence, in particular the air defence of the Ground Forces, has become one of the primary strategic factors determining the level of national security, and in the course of combat operations substantially influences the outcomes of an armed conflict or war. Maintaining the air defence weapon systems of the Ground Forces in a constant state of readiness for employment in their intended role is ensured by the precise and high-quality implementation of measures for organising their operation. The article proposes an improved methodology for assessing the effectiveness of the organisation of operation of air defence weapon systems of the Ground Forces. As the criterion of effectiveness of the organisation of weapon operation, the requirement is adopted that the readiness coefficient for employment in the intended role shall be no worse than the specified value, that the time for bringing to readiness, deployment and redeployment, operational maintainability, and operational safety meet the established requirements given the available resource margin. This approach allows a more objective assessment of the effectiveness of the organisation of weapon operation for the purpose of making the necessary decisions to improve the situation where required
- Open Access
- 24 April 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
- No. 1,p. 55-62
MODEL FOR EVALUATING THE PARAMETERS OF CORNER REFLECTORS FOR AERIAL TARGETS
An important element of the target equipment of modern and prospective target drones is the means for simulating the radar cross-section (RCS) of various types of aerial targets in the microwave frequency band. The most common passive aerial target simulators are corner reflectors (triangular, square, circular, and biconical). Conducted research has shown that among corner reflectors for aerial targets, the square reflector provides the largest radar cross-section. However, it also has the narrowest backscattering patterns in both planes and a less robust structure. Triangular corner reflectors for aerial targets provide the widest monostatic backscattering patterns in both planes, which defines their advantages in use, despite their relatively low RCS value. Compared to others, corner reflectors are simple in design, manufacturable, possess high mechanical rigidity, and provide sufficiently good RCS values over wide ranges of illumination aspects with relatively small physical dimensions. A model for evaluating the parameters of corner reflectors for aerial targets has been developed. It allows for calculating their values based on input data about the target's radar cross-section and the frequency of the illuminating electromagnetic wave. The obtained simulation data confirm the prospects of using the developed model for evaluating corner reflector parameters when creating targets for air attack means
- 24 April 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
- No. 1,p. 55-62
Open AccessMODEL FOR EVALUATING THE PARAMETERS OF CORNER REFLECTORS FOR AERIAL TARGETS
An important element of the target equipment of modern and prospective target drones is the means for simulating the radar cross-section (RCS) of various types of aerial targets in the microwave frequency band. The most common passive aerial target simulators are corner reflectors (triangular, square, circular, and biconical). Conducted research has shown that among corner reflectors for aerial targets, the square reflector provides the largest radar cross-section. However, it also has the narrowest backscattering patterns in both planes and a less robust structure. Triangular corner reflectors for aerial targets provide the widest monostatic backscattering patterns in both planes, which defines their advantages in use, despite their relatively low RCS value. Compared to others, corner reflectors are simple in design, manufacturable, possess high mechanical rigidity, and provide sufficiently good RCS values over wide ranges of illumination aspects with relatively small physical dimensions. A model for evaluating the parameters of corner reflectors for aerial targets has been developed. It allows for calculating their values based on input data about the target's radar cross-section and the frequency of the illuminating electromagnetic wave. The obtained simulation data confirm the prospects of using the developed model for evaluating corner reflector parameters when creating targets for air attack means
- Open Access
- 28 February 2026
- Published by Ukrainian Scientific Community in Journal of Scientific Papers "Social development and Security"
- Vol. 16 (1) , 102-115
Керуючий алгоритм оцінки боєздатності військових підрозділів
Мета роботи. Обґрунтування та розроблення керуючого алгоритму оцінки боєздатності військових підрозділів з метою планування та проведення організаційно-технічним заходів, спрямованих на підтримання та відновлення їх боєздатності. Метод дослідження. У дослідженні застосовано системний і порівняльний аналіз існуючих підходів до оцінки боєздатності підрозділів, методи структурно-функціонального синтезу та математичного моделювання та алгоритмізації для розроблення керуючого алгоритму оцінки, а також імовірнісні методи для оцінювання потенційної технічної спроможності та рівня професійної та морально-психологічної підготовки особового складу. Результати дослідження. У роботі запропоновано керуючий алгоритм, що структурно складається з 13 блоків, розміщених на 5 ієрархічних рівнях. Алгоритм реалізує послідовність дій: збір та аналіз інформації, окремі оцінки потенційної технічної спроможності та рівня професійної та морально-психологічної підготовки, інтегральну оцінку рівня боєздатності, формування та коригування управлінських рішень. Виведено аналітичні залежності для розрахунку потенційної технічної спроможності та рівня професійної та морально-психологічної підготовки, що дозволяють кількісно оцінити стан підрозділу. Визначено три ступені боєздатності (боєздатний, обмежено боєздатний, небоєздатний) на основі інтегрального показника та критичних втрат. Практична цінність дослідження. Отримані результати можуть бути використані підрозділами Збройних сил України, Національної гвардії України та іншими складовими сил оборони. Керуючий алгоритм є інструментом для командування та штабів з об'єктивної оцінки стану підрозділів, планування організаційно-технічних заходів щодо підтримання та відновлення боєздатності, прийняття обґрунтованих рішень щодо застосування сил. Майбутні дослідження. Подальші дослідження доцільно спрямувати на розроблення практичних рекомендацій та ефективних способів підтримання та відновлення боєздатності військових підрозділів. Тип статті. Дослідницька.
- 28 February 2026
- Published by Ukrainian Scientific Community in Journal of Scientific Papers "Social development and Security"
- Vol. 16 (1) , 102-115
Open AccessКеруючий алгоритм оцінки боєздатності військових підрозділів
Мета роботи. Обґрунтування та розроблення керуючого алгоритму оцінки боєздатності військових підрозділів з метою планування та проведення організаційно-технічним заходів, спрямованих на підтримання та відновлення їх боєздатності. Метод дослідження. У дослідженні застосовано системний і порівняльний аналіз існуючих підходів до оцінки боєздатності підрозділів, методи структурно-функціонального синтезу та математичного моделювання та алгоритмізації для розроблення керуючого алгоритму оцінки, а також імовірнісні методи для оцінювання потенційної технічної спроможності та рівня професійної та морально-психологічної підготовки особового складу. Результати дослідження. У роботі запропоновано керуючий алгоритм, що структурно складається з 13 блоків, розміщених на 5 ієрархічних рівнях. Алгоритм реалізує послідовність дій: збір та аналіз інформації, окремі оцінки потенційної технічної спроможності та рівня професійної та морально-психологічної підготовки, інтегральну оцінку рівня боєздатності, формування та коригування управлінських рішень. Виведено аналітичні залежності для розрахунку потенційної технічної спроможності та рівня професійної та морально-психологічної підготовки, що дозволяють кількісно оцінити стан підрозділу. Визначено три ступені боєздатності (боєздатний, обмежено боєздатний, небоєздатний) на основі інтегрального показника та критичних втрат. Практична цінність дослідження. Отримані результати можуть бути використані підрозділами Збройних сил України, Національної гвардії України та іншими складовими сил оборони. Керуючий алгоритм є інструментом для командування та штабів з об'єктивної оцінки стану підрозділів, планування організаційно-технічних заходів щодо підтримання та відновлення боєздатності, прийняття обґрунтованих рішень щодо застосування сил. Майбутні дослідження. Подальші дослідження доцільно спрямувати на розроблення практичних рекомендацій та ефективних способів підтримання та відновлення боєздатності військових підрозділів. Тип статті. Дослідницька.
- 7 February 2026
- Published by Springer Nature
- p. 92-99
Model of Multicomponent Complex Motion as a Basis for Controlling a Group of Unmanned Platforms
- 7 February 2026
- Published by Springer Nature
- p. 92-99
Model of Multicomponent Complex Motion as a Basis for Controlling a Group of Unmanned Platforms
- Open Access
- 30 January 2026
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 1,p. 3-17
Assessing the electromagnetic interaction of silver nanoparticles in the optical band
The object of the study is the resonant effects of electromagnetic wave scattering by two silver nanoparticles in the optical range. The study considered the problem of the influence of the electromagnetic interaction between nanoparticles on the characteristics of light scattering and absorption by a model of two silver nanoparticles and determining the limit when this interaction can be neglected. Methods for calculating the scattering characteristics by this model are proposed. The methods are based on solving the system of surface integral Muller equations for a set of nanoparticles. The values of the total scattering, attenuation and absorption cross sections for a model of two ellipsoidal nanoparticles of different sizes with variable distances between them on two orthogonal polarizations are obtained. The first model consists of two nanoparticles with semi-axes of 75 × 75 × 25 nm, the second – 100 × 100 × 20 nm. The calculations were performed taking into account the electromagnetic interaction between nanoparticles when determining the current densities on their surfaces and without taking into account the specified interaction. As a numerical measure of the degree of electromagnetic interaction, the relative error in the calculation of the scattering characteristics of the models when taking into account the interaction and when neglecting it was used. The estimation of the limiting distances at which the interaction between nanoparticles can be neglected with a given accuracy was carried out. For an error in the calculation of scattering cross sections of less than 5% at a wavelength of λ = 300 nm, the limiting distance is from 0.4λ to 3λ (from 120 nm to 900 nm) depending on the polarization. The use of the approximate method at these distances while maintaining accuracy allowed to reduce the dimensionality of the system of integral equations by a factor of 4, which significantly reduced the computational costs. The proposed method can be generalized to nanoparticles of different sizes and from other noble metals.
- 30 January 2026
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 1,p. 3-17
Open AccessAssessing the electromagnetic interaction of silver nanoparticles in the optical band
The object of the study is the resonant effects of electromagnetic wave scattering by two silver nanoparticles in the optical range. The study considered the problem of the influence of the electromagnetic interaction between nanoparticles on the characteristics of light scattering and absorption by a model of two silver nanoparticles and determining the limit when this interaction can be neglected. Methods for calculating the scattering characteristics by this model are proposed. The methods are based on solving the system of surface integral Muller equations for a set of nanoparticles. The values of the total scattering, attenuation and absorption cross sections for a model of two ellipsoidal nanoparticles of different sizes with variable distances between them on two orthogonal polarizations are obtained. The first model consists of two nanoparticles with semi-axes of 75 × 75 × 25 nm, the second – 100 × 100 × 20 nm. The calculations were performed taking into account the electromagnetic interaction between nanoparticles when determining the current densities on their surfaces and without taking into account the specified interaction. As a numerical measure of the degree of electromagnetic interaction, the relative error in the calculation of the scattering characteristics of the models when taking into account the interaction and when neglecting it was used. The estimation of the limiting distances at which the interaction between nanoparticles can be neglected with a given accuracy was carried out. For an error in the calculation of scattering cross sections of less than 5% at a wavelength of λ = 300 nm, the limiting distance is from 0.4λ to 3λ (from 120 nm to 900 nm) depending on the polarization. The use of the approximate method at these distances while maintaining accuracy allowed to reduce the dimensionality of the system of integral equations by a factor of 4, which significantly reduced the computational costs. The proposed method can be generalized to nanoparticles of different sizes and from other noble metals.
- 17 January 2026
- Published by Springer Nature
- p. 27-37
Method for Selecting Design Solution Interference-Fit Joints in Automated Design Systems
- 17 January 2026
- Published by Springer Nature
- p. 27-37
Method for Selecting Design Solution Interference-Fit Joints in Automated Design Systems
- Open Access
- 30 December 2025
- Published by Kyiv institute of the National Guard of Ukraine in Науковий вісник Київського інституту Національної гвардії України
- No. 2
DEFINING THE FREQUENCY DEPENDENCIES OF THE RADAR CROSS SECTION OF LENS SIMULATORS OF AIR TARGETS FOR VARIOUS DIELECTRIC MATERIALS
The main characteristic of air attack weapons, such as radar targets is their radar cross section. This parameter characterises the reflective properties of the target and determines its energy characteristics in terms of secondary radiation at the reception point and does not depend on the intensity of the primary wave. One of the most acceptable and promising passive simulators of the radar cross section of air targets in the radar wave range is the multilayered Luneburg lens. However, when manufacturing spherical lens-based simulators as multilayer structures, the discreteness of dielectric permittivity and additional technological errors lead to a reduction in their radar cross section compared to theoretically achievable values. A methodological approach has been proposed to evaluate the influence of these factors on the deviation of the actual radar cross section of lens-based simulators from their theoretical values. An algorithm for a computational and experimental method has been developed to estimate the real values of the radar cross section of passive simulators based on multilayered spherical Luneburg lenses using anechoic chambers. The measurement and evaluation of the real radar cross section of lens-based simulators rely on a reference reflector in the form of a metal sphere with a known radar cross section. The experimental results demonstrated that the reduction in radar cross section of air target simulators compared to theoretical values depends on both the dielectric material (such as PET and PETG) and the irradiation frequency. The average radar cross section reduction coefficient for simulators made of PET-type dielectric material is approximately 2.9 dB. The obtained research results will be used in practice in the design of compact and cheap air target simulators with specified reflective characteristics, as well as in the creation of false targets that complicate the work of enemy air defenses.
- 30 December 2025
- Published by Kyiv institute of the National Guard of Ukraine in Науковий вісник Київського інституту Національної гвардії України
- No. 2
Open AccessDEFINING THE FREQUENCY DEPENDENCIES OF THE RADAR CROSS SECTION OF LENS SIMULATORS OF AIR TARGETS FOR VARIOUS DIELECTRIC MATERIALS
The main characteristic of air attack weapons, such as radar targets is their radar cross section. This parameter characterises the reflective properties of the target and determines its energy characteristics in terms of secondary radiation at the reception point and does not depend on the intensity of the primary wave. One of the most acceptable and promising passive simulators of the radar cross section of air targets in the radar wave range is the multilayered Luneburg lens. However, when manufacturing spherical lens-based simulators as multilayer structures, the discreteness of dielectric permittivity and additional technological errors lead to a reduction in their radar cross section compared to theoretically achievable values. A methodological approach has been proposed to evaluate the influence of these factors on the deviation of the actual radar cross section of lens-based simulators from their theoretical values. An algorithm for a computational and experimental method has been developed to estimate the real values of the radar cross section of passive simulators based on multilayered spherical Luneburg lenses using anechoic chambers. The measurement and evaluation of the real radar cross section of lens-based simulators rely on a reference reflector in the form of a metal sphere with a known radar cross section. The experimental results demonstrated that the reduction in radar cross section of air target simulators compared to theoretical values depends on both the dielectric material (such as PET and PETG) and the irradiation frequency. The average radar cross section reduction coefficient for simulators made of PET-type dielectric material is approximately 2.9 dB. The obtained research results will be used in practice in the design of compact and cheap air target simulators with specified reflective characteristics, as well as in the creation of false targets that complicate the work of enemy air defenses.