DLDai Xuan Lu

Dai Xuan Lu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Dai Xuan Lu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Can RAP from Crumb Rubber-Modified Asphalt Mixtures be Recycled Seamlessly as Standard RAP? A Comprehensive Laboratory Study

    by Dai Xuan Lu, Gokul Balasubramaniam, Marie Enfrin, Filippo Giustozzi

    The recycling of end-of-life tyres such as crumb rubber (CR) in asphalt mixtures for roads addresses landfill and environmental issues. However, if a reclaimed crumb rubber asphalt mixture (CR-RAP) cannot be recycled, it may defer waste issues rather than offering a true eco-friendly solution. In this work, the future recyclability of dense graded CR-modified asphalt mixtures is investigated. In particular, this work examined the performance of a dense-graded asphalt mixture prepared with CR-RAP added at 15% and 30%. CR-RAP was manufactured in the laboratory by artificially ageing a CR asphalt mixture at two different ageing levels, equivalent to approximately 10 and 20 years of field ageing. Construction aspects, as well as key performance indicators of moisture damage, cracking and rutting resistance, were evaluated. The study revealed that adding more CR-RAP tends to reduce compactability. However, the asphalt mixtures with 15% and 30% CR-RAP added in this study had sufficient compactability. The study revealed that the inclusion of CR-RAP in a mixture does not generate additional moisture resistance issues; instead, it enhances the moisture resistance of the asphalt mixture. Compared with standard RAP, the inclusion of 30% CR-RAP can reduce cracking while improving rutting resistance in the asphalt mixture. Overall, the study suggests that CR-modified asphalt mixtures can be effectively recycled as conventional RAP in dense-graded asphalt mixtures. However, a high content of CR-RAP in dense graded asphalt mixtures might lead to compaction issues during construction if a proper mix design method is not employed.


  • Open Access

    Performance Evaluation of Post-Consumer and Post-Industrial Recycled Plastics as Binder Modifier in Asphalt Mixes

    by Dai Xuan Lu, Marie Enfrin, Hassan Masood, Filippo Giustozzi

    This study aims to analyse the behaviour of asphalt concrete produced from recycled plastic-modified bitumen. This particular production process is known as the wet method, which involves the blending of low melting point recycled plastics, mostly polyolefins, in hot bitumen before mixing with preheated aggregate. Based on a comprehensive research study that investigated several recycled plastics for the wet method, two common low melting point plastics from two different collection streams were evaluated: a low-density polyethylene from post-industrial recycling operations and a source of commingled plastic (polyethylene and polypropylene) from the collection of post-consumer plastics. Plastic-modified bitumen was produced with different recycled plastic contents ranging from 0.5 to 6% of the bitumen weight. First, the storage stability of the plastic-modified bitumen was evaluated. Then, asphalt mixes were produced using the plastic-modified bitumen. The testing scheme included measurements of the compactability and densification behaviour of the mixes, moisture resistance, viscoelastic behaviour via the flexural stiffness test, IDEAL-CT test to evaluate cracking tolerance, fatigue resistance through the four-point bending beam test, and rutting resistance via Hamburg wheel tracking. The study found that adding a high plastic content significantly reduced the storage stability of the plastic-modified bitumen. Adding plastic was found to have a minor impact on the compactability, while it reduced the moisture resistance with increasing plastic addition and modified the viscoelastic behaviour of the asphalt mixtures. Finally, the study found that plastic provided benefits to the cracking and rutting resistance of asphalt mixtures to different extents depending on the plastic type and plastic content.


  • Open Access

    Production and use of crumb rubber for bitumen modification from end-of-life passenger car tyres in comparison with truck tyres: a comprehensive study on bitumen and asphalt performance

    by Michael Swaney, Dai Xuan Lu, Da Sun, Filippo Giustozzi

    The use of crumb rubber (CR) from shredded end-of-life vehicle tyres in road engineering practices has become increasingly popular as a method of enhancing sustainability. Historically, crumb rubber produced from end-of-life tyres only used sources of rubber with high natural rubber content. This approach was believed to enhance the final properties of the crumb rubber modified binder, hence also providing betterments to the asphalt mix. The presence of a lower volume of textile fibre in radial truck tyres (TT) also contributed to the recycling of these type of tyres for road applications. However, with the development of more efficient recycling machines, and with the raised awareness that passenger car tyres are available in a much larger quantity, new research is needed to explore the suitability of recycling passenger car tyres (PCT) for bitumen modification. This study aims to evaluate the possible use of PCT in bitumen by studying its performance and comparing it to the performance of the same bitumen modified with TT and S45R (a commercial crumb rubber modified binder). Different percentages of PCT CR and TT CR were added to a neat binder, and their composition and performance were analysed through a series of physical, chemical, and rheological tests. The results indicate that adding PCT CR to neat bitumen can significantly improve the temperature susceptibility, elasticity, hardness, and stiffness of the binder, thus improving the rutting performance and resistance to fatigue similar to what TT CR can do. From a direct comparison, the performance of PCT CR modified binders is very similar to TT CR, especially at lower CR content (i.e. below 10%). Additionally, PCT CR in the approximate range of 13–16% by weight of bitumen would provide similar results to the commercially available S45R binder for most of the tests conducted. Consequently, selected binders and modified binders (with 15% and 20% CR) with a warm mix additive were used to produce a gap graded asphalt mix for mechanical behaviour evaluation on compactability, moisture resistance, non-damage viscoelastic behaviour, cracking, and rutting resistance. The study found minimal differences between the two sources of rubber (PCT and TT). Overall, PTC were found to be suitable to produce CR for bitumen modification through the wet process.

  • Laboratory evaluation of PAH and VOC emission from plastic-modified asphalt

    by Yeong Jia Boom, Marie Enfrin, Dai Lu Xuan, Stephen Grist, Dilan Robert, Filippo Giustozzi


  • Evaluation of Fracture and Fatigue Cracking Characterization Ability of Nonstandardized Semicircular-Bending Test for Asphalt Concrete

    by Dai Xuan Lu, Mofreh Saleh, Nhu H. T. Nguyen

    Reclaimed asphalt pavement (RAP) has been used recently in warm-mix asphalt (WMA) as a part of sustainable and green pavement design. The main issue of using high RAP content in WMA is associated cracking. To optimize the use of RAP in WMA and reduce life cycle costs, a robust tool of testing to control the quality of asphalt mixtures in terms of cracking is vital. Among the available tests, the semicircular-bending (SCB) test is regarded as simple but useful to characterize the cracking behavior of asphalt concrete. The test has been standardized in a number of standards for 150-mm-diameter samples. Recently, the authors investigated and proved that the SCB test on 100-mm-diameter samples produced acceptable repeatability compared with standardized samples based on experimental and numerical tests, providing an alternative choice for practitioners and researchers with the tools and equipment available to conduct the test. However, the characterization ability of cracking behavior, in particular the fracture and fatigue, of asphalt mixtures using this nonstandardized test has not been studied yet. Thus, this study was conducted to investigate the potential for characterization of cracking behavior of nonstandardized SCB testing for asphalt mixtures. Laboratory tests were conducted on different mixtures, including hot-mix asphalt, WMA, and WMA with added RAP. A four-point bending fatigue test was also performed to compare with results from the SCB test. The study found that the SCB test on nonstandard samples could be used to evaluate the cracking resistance of asphalt mixtures. It was also found that production temperatures, WMA technologies, RAP contents, notch lengths, and air voids considerably affected the cracking behavior of asphalt mixtures.