Braion B. de Moura
Research Subjects
Braion B. de Moura has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Marcela Rodrigues Machado
Department of Mechanical Engineering, University of Brasília, Campus Universitário Darcy Ribeiro, Brasília, 70910-900, Brazil
4 shared publications - Adriano Todorovic Fabro
Department of Mechanical Engineering, University of Brasília, Brasília, Brazil
1 shared publication - Juliana C. Santos
University of Brasília, Brazil
1 shared publication - Leila Khalij
Normandie University
1 shared publication - Lucas S. Barreto
Universidade de Brasília, Brazil
1 shared publication - Sudip Dey
National Institute of Technology
1 shared publication
Latest Publications
- 22 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 25-29
Investigation of Synthetic Inductance for Resonant Shunt Circuit Applied to Vibration Control
Resistive-inductive shunt circuits, also called resonant shunt circuits, are commonly used in conjunction with piezoelectric materials to promote passive vibration control. These circuits work similarly to a band-pass filter, tuning a certain frequency range and dissipating the piezoelectric energy relevant to the tuning. However, there is a problem when there is a need for low-frequency tuning. This problem is caused by the inductive element of the circuit, as there is an inversely proportional relationship between the inductive value and frequency tuning. In other words, to choose to tune a low frequency we will have to use a high-value inductor, which denotes the generation of an electromagnetic field due to the coil which in this aspect is also volumetrically unfeasible for storage in small areas. That said, the present study aims to analyze and compare the use of three synthetic inductance circuits for low-frequency tuning, they are: the Antoniou circuit; the Riodan circuit; and the Gyrator circuit. These inductances were compared in four cases where different resistive values selected the same tuning zone. The results demonstrate that both synthetic inductances showed similar dissipation effects, but in the Gyrator inductance, there was slightly less dissipation for both cases analyzed.
- 22 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 25-29
Investigation of Synthetic Inductance for Resonant Shunt Circuit Applied to Vibration Control
Resistive-inductive shunt circuits, also called resonant shunt circuits, are commonly used in conjunction with piezoelectric materials to promote passive vibration control. These circuits work similarly to a band-pass filter, tuning a certain frequency range and dissipating the piezoelectric energy relevant to the tuning. However, there is a problem when there is a need for low-frequency tuning. This problem is caused by the inductive element of the circuit, as there is an inversely proportional relationship between the inductive value and frequency tuning. In other words, to choose to tune a low frequency we will have to use a high-value inductor, which denotes the generation of an electromagnetic field due to the coil which in this aspect is also volumetrically unfeasible for storage in small areas. That said, the present study aims to analyze and compare the use of three synthetic inductance circuits for low-frequency tuning, they are: the Antoniou circuit; the Riodan circuit; and the Gyrator circuit. These inductances were compared in four cases where different resistive values selected the same tuning zone. The results demonstrate that both synthetic inductances showed similar dissipation effects, but in the Gyrator inductance, there was slightly less dissipation for both cases analyzed.
- 7 October 2022
- Published by Springer Nature
- p. 725-733
Rainbow Smart Metamaterial to Improve Flexural Wave Isolation and Vibration Attenuation of a Beam
- 7 October 2022
- Published by Springer Nature
- p. 725-733
Rainbow Smart Metamaterial to Improve Flexural Wave Isolation and Vibration Attenuation of a Beam
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 18 (2)
Damage indices evaluation for one-dimensional guided wave-based structural health monitoring
Damage detection in structures and systems is essential for monitoring parameters that can affect their integrity. This paper evaluates the efficiency of four damage indices (DIs) commonly used with temporal wave signals. The root mean square deviation, mean absolute percentage deviation, covariance, and correlation coefficient deviation DIs are presented, and a normalization is then proposed. An Euler-Bernoulli beam is used as a guided wave modelled with the spectral element method and excited by a toneburst signal. It includes the theoretical background of the throw-off beam, undamaged and cracked beam spectral elements. The DIs for a single crack position and a map varying crack depth and positions are calculated with deterministic and random temporal signal responses derived from noise addition. Results showed that DIs could identify and quantify the damage conditioned to the pulse location point and the influence of noise in the estimation, which leads in an analysis comparable to practical applications.
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 18 (2)
Open AccessDamage indices evaluation for one-dimensional guided wave-based structural health monitoring
Damage detection in structures and systems is essential for monitoring parameters that can affect their integrity. This paper evaluates the efficiency of four damage indices (DIs) commonly used with temporal wave signals. The root mean square deviation, mean absolute percentage deviation, covariance, and correlation coefficient deviation DIs are presented, and a normalization is then proposed. An Euler-Bernoulli beam is used as a guided wave modelled with the spectral element method and excited by a toneburst signal. It includes the theoretical background of the throw-off beam, undamaged and cracked beam spectral elements. The DIs for a single crack position and a map varying crack depth and positions are calculated with deterministic and random temporal signal responses derived from noise addition. Results showed that DIs could identify and quantify the damage conditioned to the pulse location point and the influence of noise in the estimation, which leads in an analysis comparable to practical applications.
- 23 October 2020
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 15 (12)
Spectral Element Approach for Flexural Waves Control in Smart Material Beam With Single and Multiple Resonant Impedance Shunt Circuit
The accurate prediction of the dynamic characteristics of a structure is key to successful vibration control strategies. A typical vibration and wave propagation control is performed through periodic and shunted piezoelectric patches, also known as a smart material. Therefore, the smart metamaterial considers periodic arrangement of shunted piezoelectric patches providing a beam with attenuation properties which depend on the resonant behavior of the shunts. The vibration attenuation occurs due to an elastic-electrical system characterized by an internal resonance of the shunt circuit. The spectral element approach provides very accurate solutions for the structural dynamic response. In this paper, a beam-piezoelectric structure is introduced to focus on the control of flexural waves in beams with piezolayers connected to single and multiresonant shunt approaches. The smart structure is modeled using the spectral element method. It is shown that the effective wavenumber presents the locally resonant behavior at the same frequencies of the vibration attenuation for both single and multishunt approached, indicating that each shunt circuit is independently associated with a attenuation frequency. The spectral element approach presented in this paper shows to be an accurate and simple approach for the design smart metamaterial beams.
- 23 October 2020
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 15 (12)
Spectral Element Approach for Flexural Waves Control in Smart Material Beam With Single and Multiple Resonant Impedance Shunt Circuit
The accurate prediction of the dynamic characteristics of a structure is key to successful vibration control strategies. A typical vibration and wave propagation control is performed through periodic and shunted piezoelectric patches, also known as a smart material. Therefore, the smart metamaterial considers periodic arrangement of shunted piezoelectric patches providing a beam with attenuation properties which depend on the resonant behavior of the shunts. The vibration attenuation occurs due to an elastic-electrical system characterized by an internal resonance of the shunt circuit. The spectral element approach provides very accurate solutions for the structural dynamic response. In this paper, a beam-piezoelectric structure is introduced to focus on the control of flexural waves in beams with piezolayers connected to single and multiresonant shunt approaches. The smart structure is modeled using the spectral element method. It is shown that the effective wavenumber presents the locally resonant behavior at the same frequencies of the vibration attenuation for both single and multishunt approached, indicating that each shunt circuit is independently associated with a attenuation frequency. The spectral element approach presented in this paper shows to be an accurate and simple approach for the design smart metamaterial beams.