Andi Trimulyono
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Andi Trimulyono has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Muhammad Iqbal
Department of Naval Architecture, Faculty of Engineering, Universitas Diponegoro, Semarang 50275, Indonesia
6 shared publications - Ahmad Firdhaus
Diponegoro University
3 shared publications - Ocid Mursid
Department of Naval Architecture, Faculty of Engineering, Universitas Diponegoro, Semarang 50275, Indonesia
3 shared publications - Samuel Samuel
Department of Naval Architecture, Faculty of Engineering, Diponegoro University, Semarang 50275, Indonesia
3 shared publications Deddy Chrismianto
2 shared publications- Good Rindo
Department of Naval Architecture, Faculty of Engineering, Diponegoro University, Semarang 50275, Indonesia
2 shared publications
Latest Publications
- Open Access
Engineering Design of Stepped Hull for Planing Vessels Using CFD-Based Evaluation
The growing demand for high-speed marine transportation requires continuous improvement in ship design to achieve higher hydrodynamic efficiency. From an engineering design perspective, hull form modification is a key approach to optimizing the performance of planing vessels, particularly through the implementation of stepped hull configurations. This study aims to investigate the effects of step geometry and step position on the resistance and trim characteristics of a planing hull based on Taunton et al.’s Model C, with the objective of improving vessel efficiency. The design methodology integrates hull geometry modification, parametric variation in step position and step height, and numerical performance assessment. In this research, the governing equations are solved using the Reynolds-Averaged Navier–Stokes (RANS) framework with the Finite Volume Method (FVM) as the discretization technique. The turbulence model used is k-ω SST, while the interaction between water and air phases is represented using the Volume of Fluid (VOF) method. From a design performance perspective, the results demonstrate that stepped hull geometry significantly influences resistance and trim characteristics. The optimal design configurations achieved a resistance reduction of up to 17.93% and a trim of 1.53° was achieved with a stepped position of 430 mm from the transom and a stepped height of 25 mm (Model A3) at Fr 2.28. Meanwhile, a resistance reduction of 15.49% and a trim of 1.46° were observed for a stepped position of 860 mm from the transom and a stepped height of 25 mm (Model B3) at Fr 2.72. These findings highlight the importance of step geometry and placement as key design variables in improving planing hull performance. This study demonstrates that CFD-based evaluation can effectively support engineering design decisions for stepped hull optimization, providing a systematic approach for improving hydrodynamic efficiency in high-speed vessel design.
Open AccessEngineering Design of Stepped Hull for Planing Vessels Using CFD-Based Evaluation
The growing demand for high-speed marine transportation requires continuous improvement in ship design to achieve higher hydrodynamic efficiency. From an engineering design perspective, hull form modification is a key approach to optimizing the performance of planing vessels, particularly through the implementation of stepped hull configurations. This study aims to investigate the effects of step geometry and step position on the resistance and trim characteristics of a planing hull based on Taunton et al.’s Model C, with the objective of improving vessel efficiency. The design methodology integrates hull geometry modification, parametric variation in step position and step height, and numerical performance assessment. In this research, the governing equations are solved using the Reynolds-Averaged Navier–Stokes (RANS) framework with the Finite Volume Method (FVM) as the discretization technique. The turbulence model used is k-ω SST, while the interaction between water and air phases is represented using the Volume of Fluid (VOF) method. From a design performance perspective, the results demonstrate that stepped hull geometry significantly influences resistance and trim characteristics. The optimal design configurations achieved a resistance reduction of up to 17.93% and a trim of 1.53° was achieved with a stepped position of 430 mm from the transom and a stepped height of 25 mm (Model A3) at Fr 2.28. Meanwhile, a resistance reduction of 15.49% and a trim of 1.46° were observed for a stepped position of 860 mm from the transom and a stepped height of 25 mm (Model B3) at Fr 2.72. These findings highlight the importance of step geometry and placement as key design variables in improving planing hull performance. This study demonstrates that CFD-based evaluation can effectively support engineering design decisions for stepped hull optimization, providing a systematic approach for improving hydrodynamic efficiency in high-speed vessel design.
- Open Access
Multi-Scenario Resistance Optimisation of an Indonesian Pioneer Vessel Through Response Surface Method
Improving ship hydrodynamic efficiency is an important strategy for reducing fuel consumption and operational costs. This study investigates the optimisation of ship resistance through a combined approach involving hull form modification and operational trim adjustment. The research focuses on a pioneer vessel model, where hydrodynamic performance is analysed using Computational Fluid Dynamics (CFD) simulations coupled with Central Composite Design (CCD) and the Response Surface Methodology (RSM). Prior to the optimisation analysis, the CFD model was verified through a grid convergence study and validated against towing tank experimental data, showing good agreement. The optimisation was conducted through three scenarios: hull form optimisation, trim optimisation, and integrated optimisation, which combined both strategies. The statistical analysis revealed that longitudinal parameters play a dominant role in resistance reduction. In particular, the longitudinal centre of buoyancy (LCB) was identified as the most influential parameter in hull form optimisation, while the longitudinal centre of gravity (LCG) was the dominant parameter in trim optimisation. The results show that hull form optimisation alone reduced resistance by approximately 6%, while trim optimisation achieved a reduction of about 4%. The integrated optimisation strategy produced the greatest improvement, resulting in resistance reduction of nearly 10% compared with the baseline configuration. The findings highlight the importance of integrating design-stage optimisation and operational optimisation in improving ship hydrodynamic performance. However, the optimisation was limited to calm-water conditions.
Open AccessMulti-Scenario Resistance Optimisation of an Indonesian Pioneer Vessel Through Response Surface Method
Improving ship hydrodynamic efficiency is an important strategy for reducing fuel consumption and operational costs. This study investigates the optimisation of ship resistance through a combined approach involving hull form modification and operational trim adjustment. The research focuses on a pioneer vessel model, where hydrodynamic performance is analysed using Computational Fluid Dynamics (CFD) simulations coupled with Central Composite Design (CCD) and the Response Surface Methodology (RSM). Prior to the optimisation analysis, the CFD model was verified through a grid convergence study and validated against towing tank experimental data, showing good agreement. The optimisation was conducted through three scenarios: hull form optimisation, trim optimisation, and integrated optimisation, which combined both strategies. The statistical analysis revealed that longitudinal parameters play a dominant role in resistance reduction. In particular, the longitudinal centre of buoyancy (LCB) was identified as the most influential parameter in hull form optimisation, while the longitudinal centre of gravity (LCG) was the dominant parameter in trim optimisation. The results show that hull form optimisation alone reduced resistance by approximately 6%, while trim optimisation achieved a reduction of about 4%. The integrated optimisation strategy produced the greatest improvement, resulting in resistance reduction of nearly 10% compared with the baseline configuration. The findings highlight the importance of integrating design-stage optimisation and operational optimisation in improving ship hydrodynamic performance. However, the optimisation was limited to calm-water conditions.
- Open Access
- 1 May 2026
- Published by Academic World Research in Journal of Applied Fluid Mechanics
- Vol. 19 (5) , 991-1004
Numerical Investigation of the Effect of Spray Rail Designs on the Slamming Behaviour of Planing Hulls
Slamming loads represent a major design and operational challenge for planing hulls due to their influence on structural integrity and crew comfort. Spray rails, mounted along the hull bottom, offer benefits such as deflecting spray, enhancing hydrodynamic lift, and reducing drag by limiting the wetted surface area. However, their configuration also modifies the slamming response of the hull during water impact. This study numerically investigates the effect of three representative spray-rail geometries on the slamming behaviour of a planing hull using Computational Fluid Dynamics (CFD). Water-entry simulations of a free-falling wedge-shaped hull section are performed by solving the Unsteady Reynolds Averaged Navier Stokes (URANS) equations with the SST k-ω turbulence model. An overset grid framework is applied for mesh motion, coupled with the Volume of Fluid (VOF) method to resolve the transient air–water interface. Results show that spray rails redirect the incoming flow, reducing peak pressures at regions downstream of the rails while intensifying local pressures near the keel. Dynamic response analysis indicates that while the bare hull exhibits a single acceleration peak, the inclusion of rails introduces multiple peaks corresponding to successive rail–spray interactions. Among the tested geometries, Shallow triangular rails caused smaller increases in pressure and acceleration compared to steeper designs, which led to greater load amplification. This study demonstrates how variations in spray-rail geometry influence transient slamming loads, thereby extending existing water-entry research beyond bare-hull conditions and providing practical insight for more reliable hull strength assessment and design.
- 1 May 2026
- Published by Academic World Research in Journal of Applied Fluid Mechanics
- Vol. 19 (5) , 991-1004
Open AccessNumerical Investigation of the Effect of Spray Rail Designs on the Slamming Behaviour of Planing Hulls
Slamming loads represent a major design and operational challenge for planing hulls due to their influence on structural integrity and crew comfort. Spray rails, mounted along the hull bottom, offer benefits such as deflecting spray, enhancing hydrodynamic lift, and reducing drag by limiting the wetted surface area. However, their configuration also modifies the slamming response of the hull during water impact. This study numerically investigates the effect of three representative spray-rail geometries on the slamming behaviour of a planing hull using Computational Fluid Dynamics (CFD). Water-entry simulations of a free-falling wedge-shaped hull section are performed by solving the Unsteady Reynolds Averaged Navier Stokes (URANS) equations with the SST k-ω turbulence model. An overset grid framework is applied for mesh motion, coupled with the Volume of Fluid (VOF) method to resolve the transient air–water interface. Results show that spray rails redirect the incoming flow, reducing peak pressures at regions downstream of the rails while intensifying local pressures near the keel. Dynamic response analysis indicates that while the bare hull exhibits a single acceleration peak, the inclusion of rails introduces multiple peaks corresponding to successive rail–spray interactions. Among the tested geometries, Shallow triangular rails caused smaller increases in pressure and acceleration compared to steeper designs, which led to greater load amplification. This study demonstrates how variations in spray-rail geometry influence transient slamming loads, thereby extending existing water-entry research beyond bare-hull conditions and providing practical insight for more reliable hull strength assessment and design.
- Open Access
- 20 April 2026
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan
- Vol. 23 (2) , 122-135
Optimization of Double Bottom Design in Cargo Hold Areas: Case Study Of Tanker With Lengths 150 m and Above
The shipping industry is keep advancing to produce the most efficient ship designs, including tanker ship designs. According to MARPOL Annex 1 Regulation 19, oil tankers with a deadweight of over 600 tonnes and built after 6 July 1996 must have double side and double bottom structures. These structures are intended to prevent oil spill in the event of hull damaged. However, they significantly reduce the cargo hold volume. Therefore, the objective of this research is to optimize the cargo hold volume by optimizing the double bottom design along the cargo oil tank. One of the optimization methods that can solve this problem is the brute force search method. Unlike heuristic algorithms, it provides exact rather than approximate results, making it ideal for solving small-scale problems with shorter iteration times. In this research, the variables are the locations of two cargo landing points at each knuckle of the ship's cargo oil tank. The constraints are the regulations governing clearance, stability, freeboard, and longitudinal strength of ship. The research resulted in a new design that increased the cargo oil tank volume by 375.996 m³, equivalent to 0.865%. A new ship with the same payload can be constructed using an optimized cargo oil tank configuration, reducing both the cargo tank length and the overall ship length by 1.011 m.
- 20 April 2026
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan
- Vol. 23 (2) , 122-135
Open AccessOptimization of Double Bottom Design in Cargo Hold Areas: Case Study Of Tanker With Lengths 150 m and Above
The shipping industry is keep advancing to produce the most efficient ship designs, including tanker ship designs. According to MARPOL Annex 1 Regulation 19, oil tankers with a deadweight of over 600 tonnes and built after 6 July 1996 must have double side and double bottom structures. These structures are intended to prevent oil spill in the event of hull damaged. However, they significantly reduce the cargo hold volume. Therefore, the objective of this research is to optimize the cargo hold volume by optimizing the double bottom design along the cargo oil tank. One of the optimization methods that can solve this problem is the brute force search method. Unlike heuristic algorithms, it provides exact rather than approximate results, making it ideal for solving small-scale problems with shorter iteration times. In this research, the variables are the locations of two cargo landing points at each knuckle of the ship's cargo oil tank. The constraints are the regulations governing clearance, stability, freeboard, and longitudinal strength of ship. The research resulted in a new design that increased the cargo oil tank volume by 375.996 m³, equivalent to 0.865%. A new ship with the same payload can be constructed using an optimized cargo oil tank configuration, reducing both the cargo tank length and the overall ship length by 1.011 m.
- Open Access
- 1 January 2026
- Published by Faculty of Navigation in TransNav, the International Journal on Marine Navigation and Safety of Sea Transportation
- Vol. 20 (1) , 167-171
Effect of Perforated Baffle Shapes on Sloshing Reduction in Prismatic Tanks Using SPH Analysis
Sloshing is a phenomenon that is nonlinear in a liquid carrier, such as LNG or a tanker ship. One type of LNG carrier is the membrane-type carrier. The membrane type is similar to a prismatic tank, whose shape is suitable for a ship. This paper investigates the mitigation of sloshing in a prismatic tank by implementing a perforated baffle. There are four models of perforated baffle circles, rectangular, long ellipsoid, and short ellipsoid. The baffle position is at the midpoint of the tank, with a longitudinal position to suppress fluid in rolling motion. The filling ratios of the tank are 25% and 50%, mimicking experimental conditions with the excitation force rolling. The pressure sensor located near the free surface in 25% filling ratio was used to validate and verify the numerical approach of smoothed particle hydrodynamics (SPH). SPH is one of the numerical approaches for computational fluid dynamics (CFD) based on the particle method, which is suitable for large deformations and nonlinear free surface flows, such as sloshing. The dynamic pressure and free surface deformation after installation of the perforated baffle significantly decreased and proved the perforated baffle design suitable for the prismatic tank.
- 1 January 2026
- Published by Faculty of Navigation in TransNav, the International Journal on Marine Navigation and Safety of Sea Transportation
- Vol. 20 (1) , 167-171
Open AccessEffect of Perforated Baffle Shapes on Sloshing Reduction in Prismatic Tanks Using SPH Analysis
Sloshing is a phenomenon that is nonlinear in a liquid carrier, such as LNG or a tanker ship. One type of LNG carrier is the membrane-type carrier. The membrane type is similar to a prismatic tank, whose shape is suitable for a ship. This paper investigates the mitigation of sloshing in a prismatic tank by implementing a perforated baffle. There are four models of perforated baffle circles, rectangular, long ellipsoid, and short ellipsoid. The baffle position is at the midpoint of the tank, with a longitudinal position to suppress fluid in rolling motion. The filling ratios of the tank are 25% and 50%, mimicking experimental conditions with the excitation force rolling. The pressure sensor located near the free surface in 25% filling ratio was used to validate and verify the numerical approach of smoothed particle hydrodynamics (SPH). SPH is one of the numerical approaches for computational fluid dynamics (CFD) based on the particle method, which is suitable for large deformations and nonlinear free surface flows, such as sloshing. The dynamic pressure and free surface deformation after installation of the perforated baffle significantly decreased and proved the perforated baffle design suitable for the prismatic tank.
- Open Access
- 9 September 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (9) , 1734
Study of Applicability in Minimising Pitch Radius Gyration for Different Hull Types to Improve Seakeeping Performance
This paper presents an optimisation study to determine the best centre of gravity (CoG) position to improve seakeeping performance. Two varied parameters used in this study were the longitudinal and vertical centre of gravity (LCG and VCG). The Radius Gyration in the y-axis () is introduced as a novel single-objective function to be minimised, avoiding the complexity of the conventional seakeeping optimisation process. The quality of the seakeeping performance was evaluated by response amplitude operators (RAOs) of the heave, pitch, and vertical motion. Two different hull forms are compared to investigate the applicability of the as the objective function in seakeeping optimisation. The patrol boat and S-60 hull form are selected as representatives of a planing hull type and a displacement hull type. The optimisation was carried out by using the Central Composite Design (CCD) and response surface methodology (RSM) to model the relationship between the CoG and from large and small vessels, with the objective function minimising the . The finding shows that minimising the is more sensitive to the planing hull type compared to the displacement hull type in reducing the vertical motion in different Froude numbers and wave headings.- 9 September 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (9) , 1734
Open AccessStudy of Applicability in Minimising Pitch Radius Gyration for Different Hull Types to Improve Seakeeping Performance
This paper presents an optimisation study to determine the best centre of gravity (CoG) position to improve seakeeping performance. Two varied parameters used in this study were the longitudinal and vertical centre of gravity (LCG and VCG). The Radius Gyration in the y-axis () is introduced as a novel single-objective function to be minimised, avoiding the complexity of the conventional seakeeping optimisation process. The quality of the seakeeping performance was evaluated by response amplitude operators (RAOs) of the heave, pitch, and vertical motion. Two different hull forms are compared to investigate the applicability of the as the objective function in seakeeping optimisation. The patrol boat and S-60 hull form are selected as representatives of a planing hull type and a displacement hull type. The optimisation was carried out by using the Central Composite Design (CCD) and response surface methodology (RSM) to model the relationship between the CoG and from large and small vessels, with the objective function minimising the . The finding shows that minimising the is more sensitive to the planing hull type compared to the displacement hull type in reducing the vertical motion in different Froude numbers and wave headings. - Open Access
Numerical Investigations of Deckhouse Height to the Self-Righting Moment of the Patrol Boat
The design of patrol boats, especially in Indonesian waters with extreme sea conditions, requires good stability capabilities and self-righting moments. These conditions require patrol boats to have anti-capsized capabilities where, with these capabilities, the patrol boat can return to an upright position at extreme heeling angles. This study investigates how changing the center of gravity (CoG) due to the deckhouse height factor improves self-righting moment capabilities. Four different deckhouse heights are examined to find the optimal self-righting roll moment, with a deckhouse height in the 2.01–2.31 m range. In addition, the presence of the self-righting roll moment is also validated by the computational fluid dynamics (CFD) method using three different mesh sizes. The height of the deckhouse can significantly influence the ship’s stability. The initial investigation shows ships with minimum deckhouse heights of 2.06 m have positive righting lever arms at 170° and are classified as anti-capsized ships. It has been discovered that buoyancy and the center of gravity are crucial variables in obtaining the self-righting moment. The deckhouse’s height increases the stability of the ship’s righting arm by enhancing the metacenter point. The findings demonstrate that more excellent stability is achieved with a larger deckhouse height.
Open AccessNumerical Investigations of Deckhouse Height to the Self-Righting Moment of the Patrol Boat
The design of patrol boats, especially in Indonesian waters with extreme sea conditions, requires good stability capabilities and self-righting moments. These conditions require patrol boats to have anti-capsized capabilities where, with these capabilities, the patrol boat can return to an upright position at extreme heeling angles. This study investigates how changing the center of gravity (CoG) due to the deckhouse height factor improves self-righting moment capabilities. Four different deckhouse heights are examined to find the optimal self-righting roll moment, with a deckhouse height in the 2.01–2.31 m range. In addition, the presence of the self-righting roll moment is also validated by the computational fluid dynamics (CFD) method using three different mesh sizes. The height of the deckhouse can significantly influence the ship’s stability. The initial investigation shows ships with minimum deckhouse heights of 2.06 m have positive righting lever arms at 170° and are classified as anti-capsized ships. It has been discovered that buoyancy and the center of gravity are crucial variables in obtaining the self-righting moment. The deckhouse’s height increases the stability of the ship’s righting arm by enhancing the metacenter point. The findings demonstrate that more excellent stability is achieved with a larger deckhouse height.
- Open Access
- 23 January 2024
- Published by EDP Sciences in BIO Web of Conferences
- Vol. 89, 02005
Analysis of perforated fixed baffle at low filling ratio to reduce sloshing using SPH
Prismatic tanks are used widely in various industrial applications, including marine and petroleum, due to their ease in design and storage capacity. However, these tanks often experience sloshing issues that can affect vessel stability. Sloshing effects can cause undesirable motions and impact the system's overall performance. This study focuses on analyzing the effect of perforated shapes on fixed baffles as a solution to reduce the sloshing effect in prismatic tanks. Baffle or anti-sloshing is an internal partition used to minimize the movement of liquid in the tank. The analysis method uses Smoothed particle hydrodynamics (SPH), which is a particle method or can be referred to as mesh-free computational fluid dynamics. The parameters tested include the perforated shape and the filling ratio of the water filling in the tank. The analysis found that the perforated form of the baffles has a significant effect on reducing the sloshing effect. The perforated shape of the fixed baffles has the same impact on reducing the sloshing effect of the prismatic tank. There is no significant difference in the ability of each baffle shape to overcome the sloshing problem. The findings from this study can guide designers or engineers in designing prismatic tanks that are more stable and reduce the effects of sloshing. Using baffles with the right perforated shape can optimize tank performance in maritime and shipping.
- 23 January 2024
- Published by EDP Sciences in BIO Web of Conferences
- Vol. 89, 02005
Open AccessAnalysis of perforated fixed baffle at low filling ratio to reduce sloshing using SPH
Prismatic tanks are used widely in various industrial applications, including marine and petroleum, due to their ease in design and storage capacity. However, these tanks often experience sloshing issues that can affect vessel stability. Sloshing effects can cause undesirable motions and impact the system's overall performance. This study focuses on analyzing the effect of perforated shapes on fixed baffles as a solution to reduce the sloshing effect in prismatic tanks. Baffle or anti-sloshing is an internal partition used to minimize the movement of liquid in the tank. The analysis method uses Smoothed particle hydrodynamics (SPH), which is a particle method or can be referred to as mesh-free computational fluid dynamics. The parameters tested include the perforated shape and the filling ratio of the water filling in the tank. The analysis found that the perforated form of the baffles has a significant effect on reducing the sloshing effect. The perforated shape of the fixed baffles has the same impact on reducing the sloshing effect of the prismatic tank. There is no significant difference in the ability of each baffle shape to overcome the sloshing problem. The findings from this study can guide designers or engineers in designing prismatic tanks that are more stable and reduce the effects of sloshing. Using baffles with the right perforated shape can optimize tank performance in maritime and shipping.
- 1 October 2023
- Published by University of Dubrovnik in Naše more
- Vol. 70 (4) , 219-227
Numerical Research on the Influence of Interceptor Flaps on the Planing Hydrodynamic Performance
Samuel Samuel, Serliana Yulianti, Parlindungan Manik, Andi Trimulyono, Ahmad Firdhaus, Tuswan; Preliminary communication, pp. 219-227 Download
- 1 October 2023
- Published by University of Dubrovnik in Naše more
- Vol. 70 (4) , 219-227
Numerical Research on the Influence of Interceptor Flaps on the Planing Hydrodynamic Performance
Samuel Samuel, Serliana Yulianti, Parlindungan Manik, Andi Trimulyono, Ahmad Firdhaus, Tuswan; Preliminary communication, pp. 219-227 Download
- Open Access
- 1 May 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1166 (1) , 012032
Validation of multiphase water wave propagation using smoothed particle hydrodynamics
Water wave propagation is one of the classical problems in free surface flow that involved water and air. There are a lot of studies have been conducted on both experimental and numerical methods. One numerical method is computational fluid dynamics (CFD), which is divided into two major i.e. CFD mesh-based and meshfree. In this paper, smoothed particle hydrodynamics (SPH) is used to carry out a study of water wave propagation. SPH is a mesh-free CFD and Lagrangian approach that is suitable for free surface flow such as water waves. Two-phase SPH was used to reproduce long-distance propagation using a piston-type wavemaker. The wave probe was set 24.6 m in front of the wavemaker with a water depth is 0.75 m. The wave period is 1.15 s with an amplitude of the wavemaker is 33.0 mm. The simulation is carried out with a water and air phase (multiphase). The results indicate SPH is in reasonable agreement with experimental for the wave height, celerity, and amplitude.
- 1 May 2023
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1166 (1) , 012032
Open AccessValidation of multiphase water wave propagation using smoothed particle hydrodynamics
Water wave propagation is one of the classical problems in free surface flow that involved water and air. There are a lot of studies have been conducted on both experimental and numerical methods. One numerical method is computational fluid dynamics (CFD), which is divided into two major i.e. CFD mesh-based and meshfree. In this paper, smoothed particle hydrodynamics (SPH) is used to carry out a study of water wave propagation. SPH is a mesh-free CFD and Lagrangian approach that is suitable for free surface flow such as water waves. Two-phase SPH was used to reproduce long-distance propagation using a piston-type wavemaker. The wave probe was set 24.6 m in front of the wavemaker with a water depth is 0.75 m. The wave period is 1.15 s with an amplitude of the wavemaker is 33.0 mm. The simulation is carried out with a water and air phase (multiphase). The results indicate SPH is in reasonable agreement with experimental for the wave height, celerity, and amplitude.