JAJosé Manuel Amado

José Manuel Amado

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


José Manuel Amado has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Spectral Entropy and STFT Analysis of Thermal Signatures for Melt Pool Stability in Laser DED Repair of Complex Structures

    by Sai Vempati, Armando José Yáñez Casal, Juan Carlos Becerra Permuy, José Manuel Amado Paz, María José Tobar Vidal

    The influence of internal substrate geometry on thermal stability during Laser Directed Energy Deposition Repair (DED-R) remains insufficiently understood, particularly for components containing internal cavities and cooling channels. This study investigates the thermal response of solid (Alpha), blind-hole (Bravo), and channeled (Charlie) AISI 316L substrates using dual infrared thermography, transient finite element modeling, and Short-Time Fourier Transform (STFT)-frequency-domain analysis. Despite substantial differences in internal heat-dissipation pathways, all substrate configurations exhibited similar peak surface temperatures (~1700–2100 °C), indicating that conventional temperature monitoring alone is insufficient to distinguish geometry-dependent melt-pool behavior. To address this limitation, a Spectral Entropy Index (SEI) derived from STFT analysis was proposed to quantify thermal stability. The channeled substrate exhibited the lowest entropy value (Hs = 0.172), compared with the solid (Hs = 0.181) and blind-hole (Hs = 0.183) configurations, indicating a more ordered and predictable thermal response. Furthermore, distinct variations in the spectral stability shadow revealed geometry-dependent oscillatory behavior that was not observable from thermal histories. Finite element simulations showed good agreement with experimental measurements in conduction-dominated regions (RMSE ≈ 46 °C), whereas deviations were observed within the melt-pool region (~250–310 °C), highlighting the increasing influence of fluid-flow phenomena not captured by the conduction-based model. The results demonstrate that internal substrate architecture primarily influences melt-pool stability through frequency-domain thermodynamics rather than significant changes in peak temperature. The proposed STFT method provides a quantitative approach for monitoring thermal stability and assessing the feasibility of L-DED repair over complex internal geometries.


  • Open Access

    Deep Eutectic Solvents as Green and Novel Lubricant Additives for Castor Oil with High Tribological Performance

    by José M. Liñeira del Río, A. Aourdou, G. García-Marquínez, J. M. Amado, M. J. Tobar

    This research reveals the anti-friction and anti-wear performance of lubricants using a castor oil base and a deep eutectic solvent (DES1) as an additive. To this end, DES1 was synthesized in a successful manner using DL-menthol and dodecanoic acid as components. Mass concentrations from 0.1 wt% up to 5 wt% of DES1 additives were chosen to formulate the lubricants. Friction experiments were conducted, yielding friction enhancements up to 4% compared to the castor oil base. Notably the greatest reduction was achieved for the lubricant with 0.1 wt% of DES1. In terms of the wear generated, the best anti-wear performance was achieved for the 0.5 wt% DES1 lubricant (with a wear reduction of 17%). Furthermore, by means of the profilometry of worn surfaces, it can be observed that the tribofilm formation of DES1 on steel surfaces is a potential lubrication mechanism.


  • Open Access

    Influence of Femtosecond Laser Modification on Biomechanical and Biofunctional Behavior of Porous Titanium Substrates

    by Ana M. Beltrán, Mercè Giner, Ángel Rodríguez, Paloma Trueba, Luisa M. Rodríguez-Albelo, Maria Angeles Vázquez-Gámez, Vanda Godinho, Ana Alcudia, José M. Amado, Carmen López-Santos, et al.

    Bone resorption and inadequate osseointegration are considered the main problems of titanium implants. In this investigation, the texture and surface roughness of porous titanium samples obtained by the space holder technique were modified with a femtosecond Yb-doped fiber laser. Different percentages of porosity (30, 40, 50, and 60 vol.%) and particle range size (100–200 and 355–500 μm) were compared with fully-dense samples obtained by conventional powder metallurgy. After femtosecond laser treatment the formation of a rough surface with micro-columns and micro-holes occurred for all the studied substrates. The surface was covered by ripples over the micro-metric structures. This work evaluates both the influence of the macro-pores inherent to the spacer particles, as well as the micro-columns and the texture generated with the laser, on the wettability of the surface, the cell behavior (adhesion and proliferation of osteoblasts), micro-hardness (instrumented micro-indentation test, P–h curves) and scratch resistance. The titanium sample with 30 vol.% and a pore range size of 100–200 μm was the best candidate for the replacement of small damaged cortical bone tissues, based on its better biomechanical (stiffness and yield strength) and biofunctional balance (bone in-growth and in vitro osseointegration).


  • Open Access

    Laser Surface Modification in Ti-xNb-yMo Alloys Prepared by Powder Metallurgy

    by Inmaculada Tendero, Mariana Correa Rossi, Mauricio Viera, José Manuel Amado, María José Tobar, Ángel Vicente, Armando Yañez, Vicente Amigó

    The main objective was to study the effect of surface modification by laser on Ti-Nb-Mo powder metallurgical alloys to improve their mechano-chemical behavior and their application as a biomedical implant. The used powder mixtures were produced in an inert atmosphere. Uniaxial compaction took place at 600 MPa with high-vacuum sintering at 1250 °C for 3 h. The specimens for the three-point flexure test were prepared and their mechanical properties determined. Microstructural characterization was performed by scanning electron microscopy (SEM) and X-ray diffraction (XRD) to obtain the distribution of phases, porosity, size, and shape of the grains of each alloy. Corrosion behavior was evaluated by electrochemical tests using an artificial saliva electrolyte modified from Fusayama at 37 °C. Chemical characterization was completed by analyzing the ionic release by Inductively coupled plasma atomic emission spectroscopy (ICP-EOS) after immersion for 730 h in Fusayama solution modified with NaF at 37 °C to simulate a 20-year life span based on a daily 2-min cycle of three toothbrushes. Corrosion behavior confirmed promising possibilities for the biomedicine field. The surface porosity of the samples not submitted to surface treatment deteriorated properties against corrosion and ion release. The obtained phase was β, with a low α”-martensite percentage. The maximum resistance to bending was greater after surface fusion. Plastic deformations were above 7% under some conditions. Microhardness came close to 300 HV in heat-affected zone (HAZ) and 350 HV in fusion zone (FZ) (under the determined condition. The elastic modulus lowered by around 10%. The corrosion rate was lower in Ti-27Nb-8Mo and Ti-35Nb-6Mo. Niobium release was significant, but below the physiological limit.


  • Open Access

    Surface Modification of Porous Titanium Discs Using Femtosecond Laser Structuring

    by Ángel Rodríguez, Paloma Trueba, José Manuel Amado, María José Tobar, Mercè Giner, Vicente Amigó, Yadir Torres

    The failure of titanium implants is associated with two main problems that include the bone resorption and fracture of the surrounding bone tissue (stiffness incompatibility) and implant loosening (poor osseointegration). The development of porous titanium implants with low Young modulus solve the stress shielding phenomenon, while the modification of the implant surface must be implemented to promote a fast bond between the implant and bone. In this work, femtosecond laser micromachining was applied to modify the topography of the surface of Ti porous samples obtained by a space-holder technique to obtain hierarchical structures (micro and nano roughness patterns) to enhance osseointegration. Scanning electron microscopy, confocal laser microscopy, and image analysis were used for characterization of the surface morphology, roughness, and porosity before and after performing the laser treatment. Based on these results, the effect of the treatment on the mechanical behavior of the samples was estimated. In addition, a preliminary in-vitro test was performed to verify the adhesion of osteoblasts (filopodia presence) on modified titanium surface. Results revealed that laser texturing generated clusters of micro-holes and micro-columns both on the flat surface of the samples and inside the macro-pores, and periodic nanometric structures across the entire surface. The porous substrate offers suitable biomechanics (stiffness and yield strength) and bio-functional behavior (bone ingrowth and osseointegration), which improves the clinic success of titanium implants.