Ángel Rodríguez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ángel Rodríguez has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Mercè Giner
Departamento de Citología e Histología Normal y Patológica, Facultad de Medicina de la Universidad de Sevilla. Sociedad Española de Investigación Ósea y del Metabolismo Mineral (SEIOMM), Sevilla, España
3 shared publications - Yadir Torres
Department of Engineering and Materials Science and Transportation, University of Seville, Seville, Spain
3 shared publications - Javier Nicolás Montero Manso
Universidade da Coruña
2 shared publications - José Manuel Amado
University of A Coruña, Campus Industrial de Ferrol, CITENI, 15403 Ferrol, Spain
2 shared publications - Luisa Marleny Rodríguez-Albelo
Universidad de Sevilla
2 shared publications - Maria José Tobar
University of A Coruña, Campus Industrial de Ferrol, CITENI, 15403 Ferrol, Spain
2 shared publications
Latest Publications
- Open Access
Influence of Femtosecond Laser Modification on Biomechanical and Biofunctional Behavior of Porous Titanium Substrates
Bone resorption and inadequate osseointegration are considered the main problems of titanium implants. In this investigation, the texture and surface roughness of porous titanium samples obtained by the space holder technique were modified with a femtosecond Yb-doped fiber laser. Different percentages of porosity (30, 40, 50, and 60 vol.%) and particle range size (100–200 and 355–500 μm) were compared with fully-dense samples obtained by conventional powder metallurgy. After femtosecond laser treatment the formation of a rough surface with micro-columns and micro-holes occurred for all the studied substrates. The surface was covered by ripples over the micro-metric structures. This work evaluates both the influence of the macro-pores inherent to the spacer particles, as well as the micro-columns and the texture generated with the laser, on the wettability of the surface, the cell behavior (adhesion and proliferation of osteoblasts), micro-hardness (instrumented micro-indentation test, P–h curves) and scratch resistance. The titanium sample with 30 vol.% and a pore range size of 100–200 μm was the best candidate for the replacement of small damaged cortical bone tissues, based on its better biomechanical (stiffness and yield strength) and biofunctional balance (bone in-growth and in vitro osseointegration).
Open AccessInfluence of Femtosecond Laser Modification on Biomechanical and Biofunctional Behavior of Porous Titanium Substrates
Bone resorption and inadequate osseointegration are considered the main problems of titanium implants. In this investigation, the texture and surface roughness of porous titanium samples obtained by the space holder technique were modified with a femtosecond Yb-doped fiber laser. Different percentages of porosity (30, 40, 50, and 60 vol.%) and particle range size (100–200 and 355–500 μm) were compared with fully-dense samples obtained by conventional powder metallurgy. After femtosecond laser treatment the formation of a rough surface with micro-columns and micro-holes occurred for all the studied substrates. The surface was covered by ripples over the micro-metric structures. This work evaluates both the influence of the macro-pores inherent to the spacer particles, as well as the micro-columns and the texture generated with the laser, on the wettability of the surface, the cell behavior (adhesion and proliferation of osteoblasts), micro-hardness (instrumented micro-indentation test, P–h curves) and scratch resistance. The titanium sample with 30 vol.% and a pore range size of 100–200 μm was the best candidate for the replacement of small damaged cortical bone tissues, based on its better biomechanical (stiffness and yield strength) and biofunctional balance (bone in-growth and in vitro osseointegration).
- Open Access
Electrical Impedance of Surface Modified Porous Titanium Implants with Femtosecond Laser
The chemical composition and surface topography of titanium implants are essential to improve implant osseointegration. The present work studies a non-invasive alternative of electrical impedance spectroscopy for the characterization of the macroporosity inherent to the manufacturing process and the effect of the surface treatment with femtosecond laser of titanium discs. Osteoblasts cell culture growths on the titanium surfaces of the laser-treated discs were also studied with this method. The measurements obtained showed that the femtosecond laser treatment of the samples and cell culture produced a significant increase (around 50%) in the absolute value of the electrical impedance module, which could be characterized in a wide range of frequencies (being more relevant at 500 MHz). Results have revealed the potential of this measurement technique, in terms of advantages, in comparison to tiresome and expensive techniques, allowing semi-quantitatively relating impedance measurements to porosity content, as well as detecting the effect of surface modification, generated by laser treatment and cell culture.
Open AccessElectrical Impedance of Surface Modified Porous Titanium Implants with Femtosecond Laser
The chemical composition and surface topography of titanium implants are essential to improve implant osseointegration. The present work studies a non-invasive alternative of electrical impedance spectroscopy for the characterization of the macroporosity inherent to the manufacturing process and the effect of the surface treatment with femtosecond laser of titanium discs. Osteoblasts cell culture growths on the titanium surfaces of the laser-treated discs were also studied with this method. The measurements obtained showed that the femtosecond laser treatment of the samples and cell culture produced a significant increase (around 50%) in the absolute value of the electrical impedance module, which could be characterized in a wide range of frequencies (being more relevant at 500 MHz). Results have revealed the potential of this measurement technique, in terms of advantages, in comparison to tiresome and expensive techniques, allowing semi-quantitatively relating impedance measurements to porosity content, as well as detecting the effect of surface modification, generated by laser treatment and cell culture.
- Open Access
Surface Modification of Porous Titanium Discs Using Femtosecond Laser Structuring
The failure of titanium implants is associated with two main problems that include the bone resorption and fracture of the surrounding bone tissue (stiffness incompatibility) and implant loosening (poor osseointegration). The development of porous titanium implants with low Young modulus solve the stress shielding phenomenon, while the modification of the implant surface must be implemented to promote a fast bond between the implant and bone. In this work, femtosecond laser micromachining was applied to modify the topography of the surface of Ti porous samples obtained by a space-holder technique to obtain hierarchical structures (micro and nano roughness patterns) to enhance osseointegration. Scanning electron microscopy, confocal laser microscopy, and image analysis were used for characterization of the surface morphology, roughness, and porosity before and after performing the laser treatment. Based on these results, the effect of the treatment on the mechanical behavior of the samples was estimated. In addition, a preliminary in-vitro test was performed to verify the adhesion of osteoblasts (filopodia presence) on modified titanium surface. Results revealed that laser texturing generated clusters of micro-holes and micro-columns both on the flat surface of the samples and inside the macro-pores, and periodic nanometric structures across the entire surface. The porous substrate offers suitable biomechanics (stiffness and yield strength) and bio-functional behavior (bone ingrowth and osseointegration), which improves the clinic success of titanium implants.
Open AccessSurface Modification of Porous Titanium Discs Using Femtosecond Laser Structuring
The failure of titanium implants is associated with two main problems that include the bone resorption and fracture of the surrounding bone tissue (stiffness incompatibility) and implant loosening (poor osseointegration). The development of porous titanium implants with low Young modulus solve the stress shielding phenomenon, while the modification of the implant surface must be implemented to promote a fast bond between the implant and bone. In this work, femtosecond laser micromachining was applied to modify the topography of the surface of Ti porous samples obtained by a space-holder technique to obtain hierarchical structures (micro and nano roughness patterns) to enhance osseointegration. Scanning electron microscopy, confocal laser microscopy, and image analysis were used for characterization of the surface morphology, roughness, and porosity before and after performing the laser treatment. Based on these results, the effect of the treatment on the mechanical behavior of the samples was estimated. In addition, a preliminary in-vitro test was performed to verify the adhesion of osteoblasts (filopodia presence) on modified titanium surface. Results revealed that laser texturing generated clusters of micro-holes and micro-columns both on the flat surface of the samples and inside the macro-pores, and periodic nanometric structures across the entire surface. The porous substrate offers suitable biomechanics (stiffness and yield strength) and bio-functional behavior (bone ingrowth and osseointegration), which improves the clinic success of titanium implants.
- 1 September 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 374, 253-263
A comparison of laser deposition of commercially pure titanium using gas atomized or Ti sponge powders
- 1 September 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 374, 253-263
A comparison of laser deposition of commercially pure titanium using gas atomized or Ti sponge powders
- 1 October 2016
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 2 (4) , 539-547
Application of 3D laser manufacturing in fabrication or repair of high-value metal component for the foundry industry
Laser direct metal deposition has proven to be successful in the manufacturing of 3D parts. In this process, the required geometry is built up layer by layer on overlapping laser clad beads. The object of the study is the manufacturing and repair of the blades of a sand kneader-mixer. Though made of carbon steel as bulk material, this element includes a protective ceramic coating with high wear resistance covering the more exposed surface in order to cope with severe wear service. However, detachment of this coating is often observed therefore diminishing its service life and leading to replacement costs. As an alternative to substitution by a new part, 3D laser manufacturing was considered for repairing. The procedure involves both refurbishing steel part and depositing a metal matrix composite (CrNi-WC) as wear resistant coating. Laser deposition of a graded metal-ceramic coatings structure was designed and tested so as to avoid cracking susceptibility of the fragile material. Software developed by the authors is used to generate the path planning for the deposition process, input data are successfully taken from the part’s model as well as from the 3D scanned real part. Characteristics of the processing technique and deposited material are presented.
- 1 October 2016
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 2 (4) , 539-547
Application of 3D laser manufacturing in fabrication or repair of high-value metal component for the foundry industry
Laser direct metal deposition has proven to be successful in the manufacturing of 3D parts. In this process, the required geometry is built up layer by layer on overlapping laser clad beads. The object of the study is the manufacturing and repair of the blades of a sand kneader-mixer. Though made of carbon steel as bulk material, this element includes a protective ceramic coating with high wear resistance covering the more exposed surface in order to cope with severe wear service. However, detachment of this coating is often observed therefore diminishing its service life and leading to replacement costs. As an alternative to substitution by a new part, 3D laser manufacturing was considered for repairing. The procedure involves both refurbishing steel part and depositing a metal matrix composite (CrNi-WC) as wear resistant coating. Laser deposition of a graded metal-ceramic coatings structure was designed and tested so as to avoid cracking susceptibility of the fragile material. Software developed by the authors is used to generate the path planning for the deposition process, input data are successfully taken from the part’s model as well as from the 3D scanned real part. Characteristics of the processing technique and deposited material are presented.
- Open Access
- 1 January 2016
- Published by Elsevier in Physics Procedia
- Vol. 83, 1319-1328
Inspection of Powder Flow During LMD Deposition by High Speed Imaging
- 1 January 2016
- Published by Elsevier in Physics Procedia
- Vol. 83, 1319-1328
Open AccessInspection of Powder Flow During LMD Deposition by High Speed Imaging