Seokwon Cho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Seokwon Cho has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Kyoungdoug Min
Seoul National University
7 shared publicationsChiheon Song
Department of Mechanical Engineering, Seoul National University, Seoul, South Korea
6 shared publications- Kyoungdoug Min
Department of Mechanical Engineering, Seoul National University, 1 Gwanak-ro, Gwanak-gu, Seoul 08826, Republic of Korea
5 shared publications Namho Kim
Department of Mechanical Engineering, Seoul National University, Seoul, South Korea
5 shared publicationsSechul Oh
Department of Mechanical Engineering, Seoul National University, Seoul, South Korea
5 shared publicationsHan Ho Song
Seoul National University
3 shared publications
Latest Publications
- Open Access
- 9 September 2023
- Published by Elsevier in Applications in Energy and Combustion Science
- Vol. 16
Catalyst-heating operation in compression-ignition engines: A comprehensive understanding using large eddy simulations
- 9 September 2023
- Published by Elsevier in Applications in Energy and Combustion Science
- Vol. 16
Open AccessCatalyst-heating operation in compression-ignition engines: A comprehensive understanding using large eddy simulations
- 8 August 2022
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 24 (5) , 2223-2232
Effects of a CFD-improved dimple stepped-lip piston on thermal efficiency and emissions in a medium-duty diesel engine
Diesel piston-bowl shape is a key design parameter that affects spray-wall interactions and turbulent flow development, and in turn affects the engine’s thermal efficiency and emissions. It is hypothesized that thermal efficiency can be improved by enhancing squish-region vortices as they are hypothesized to promote fuel-air mixing, leading to faster heat-release rates. However, the strength and longevity of these vortices decrease with advanced injection timings for typical stepped-lip (SL) piston geometries. Dimple stepped-lip (DSL) pistons enhance vortex formation at early injection timings. Previous engine experiments with such a bowl show 1.4% thermal efficiency gains over an SL piston. However, soot was increased dramatically [SAE 2022-01-0400]. In a previous study, a new DSL bowl was designed using non-combusting computational fluid dynamic simulations. This improved DSL bowl is predicted to promote stronger, more rotationally energetic vortices than the baseline DSL piston: it employs shallower, narrower, and steeper-curved dimples that are placed further out into the squish region. In the current experimental study, this improved bowl is tested in a medium-duty diesel engine and compared against the SL piston over an injection timing sweep at low-load and part-load operating conditions. No substantial thermal efficiency gains are achieved at the early injection timing with the improved DSL design, but soot emissions are lowered by 45% relative to the production SL piston, likely due to improved air utilization and soot oxidation. However, these benefits are lost at late injection timings, where the DSL piston renders a lower thermal efficiency than that of the SL piston. Energy balance analyses show higher wall heat transfer with the DSL piston than with the SL piston despite a 1.3% reduction in the piston surface area. Vortex enhancement may not necessarily lead to improved efficiency as more energetic squish-region vortices can lead to higher convective heat transfer losses.
- 8 August 2022
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 24 (5) , 2223-2232
Effects of a CFD-improved dimple stepped-lip piston on thermal efficiency and emissions in a medium-duty diesel engine
Diesel piston-bowl shape is a key design parameter that affects spray-wall interactions and turbulent flow development, and in turn affects the engine’s thermal efficiency and emissions. It is hypothesized that thermal efficiency can be improved by enhancing squish-region vortices as they are hypothesized to promote fuel-air mixing, leading to faster heat-release rates. However, the strength and longevity of these vortices decrease with advanced injection timings for typical stepped-lip (SL) piston geometries. Dimple stepped-lip (DSL) pistons enhance vortex formation at early injection timings. Previous engine experiments with such a bowl show 1.4% thermal efficiency gains over an SL piston. However, soot was increased dramatically [SAE 2022-01-0400]. In a previous study, a new DSL bowl was designed using non-combusting computational fluid dynamic simulations. This improved DSL bowl is predicted to promote stronger, more rotationally energetic vortices than the baseline DSL piston: it employs shallower, narrower, and steeper-curved dimples that are placed further out into the squish region. In the current experimental study, this improved bowl is tested in a medium-duty diesel engine and compared against the SL piston over an injection timing sweep at low-load and part-load operating conditions. No substantial thermal efficiency gains are achieved at the early injection timing with the improved DSL design, but soot emissions are lowered by 45% relative to the production SL piston, likely due to improved air utilization and soot oxidation. However, these benefits are lost at late injection timings, where the DSL piston renders a lower thermal efficiency than that of the SL piston. Energy balance analyses show higher wall heat transfer with the DSL piston than with the SL piston despite a 1.3% reduction in the piston surface area. Vortex enhancement may not necessarily lead to improved efficiency as more energetic squish-region vortices can lead to higher convective heat transfer losses.
- 1 February 2022
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 24 (3) , 1077-1094
Prediction of knock propensity using stochastic modeling in a spark-ignition engine
To comply with stringent CO2 regulations, enhanced thermal efficiency has been prioritized in internal combustion engine development; however, this has strongly driven the development of engines with operating conditions more prone to knock. Current knock sensors have its limitations to decompose knock signal by degradation so that it required a cross-referencing signal. In addition, knock control intervention is currently preceded by the occurrence of the knock, leading to decrease in thermal efficiency by retarding spark timing. In the present work, a novel prediction model for knock propensity (incidence) is presented, aiming to enable active control of knock or autoignition, and to support conventional knock sensor for cross-referencing by facilitating virtual knock sensor. A zero-dimensional model-based prediction of the in-cylinder pressure is demonstrated to prevent using in-cylinder pressure transducer, along with other incorporated predictive sub-models for the residual gas fraction, heat loss, burn duration, and heat release rate. Ignition delay correlation and Livengood-Wu relation are used to predict the onset of knock, and a burn point-based criterion is newly proposed for application in stochastic modeling for determining the knock propensity. The predicted knock propensity from the combined holistic model shows a remarkable agreement with experimental results.
- 1 February 2022
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 24 (3) , 1077-1094
Prediction of knock propensity using stochastic modeling in a spark-ignition engine
To comply with stringent CO2 regulations, enhanced thermal efficiency has been prioritized in internal combustion engine development; however, this has strongly driven the development of engines with operating conditions more prone to knock. Current knock sensors have its limitations to decompose knock signal by degradation so that it required a cross-referencing signal. In addition, knock control intervention is currently preceded by the occurrence of the knock, leading to decrease in thermal efficiency by retarding spark timing. In the present work, a novel prediction model for knock propensity (incidence) is presented, aiming to enable active control of knock or autoignition, and to support conventional knock sensor for cross-referencing by facilitating virtual knock sensor. A zero-dimensional model-based prediction of the in-cylinder pressure is demonstrated to prevent using in-cylinder pressure transducer, along with other incorporated predictive sub-models for the residual gas fraction, heat loss, burn duration, and heat release rate. Ignition delay correlation and Livengood-Wu relation are used to predict the onset of knock, and a burn point-based criterion is newly proposed for application in stochastic modeling for determining the knock propensity. The predicted knock propensity from the combined holistic model shows a remarkable agreement with experimental results.
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Performance of Octane Index in Ltgc Engines from Beyond Mon to Beyond Ron
This work analyzes the ability of the Octane Index (OI) to characterize the autoignition resistance of gasoline-like fuels in a Low-Temperature Gasoline Combustion (LTGC) engine. Experimental studies in the Sandia LTGC engine at naturally aspirated ‘beyond-MON’ and high-boost ‘beyond-RON’ conditions showed that the correlation between OI and autoignition reactivity is poor. These experiments were successfully replicated in CHEMKIN, allowing detailed studies of the factors affecting the OI correlation. Systematic investigations were conducted to determine why the OI performs less well for LTGC combustion compared to end-gas autoignition (i.e. knock) in spark-ignition (SI) engines. A pseudo-MON condition that follows the pressure-temperature (P-T) trajectory of the real MON test was tested numerically, using 10 different fuels, leading to the conclusion that the OI correlation performs very well for an SI engine running at close-to-MON conditions. The effects of each difference between SI and LTGC combustion were then analyzed for four P-T trajectories: ‘beyond-MON’, ‘MON test’, ‘between RON-MON’, and ‘beyond-RON’ conditions. These differences included changes in: equivalence ratio, engine speed, and residence-time history along the P-T trajectory for piston-only compression, as used for LTGC, compared to compression by the piston plus flame propagation for SI combustion. For LTGC combustion, the OI correlation did not characterize the autoignition quality of gasoline-like fuels well for any P-T trajectory, but the factors causing this poor performance varied with conditions. For example, at naturally aspirated LTGC conditions (beyond-MON), changes in equivalence ratio were the primary cause, followed by differences in the P-T trajectory and changes in residence time. Whereas, for intake-boosted beyond-RON conditions, differences in the P-T trajectory had the largest effect, followed by changes in residence time. Finally, the parameter K that characterizes the OI correlation showed values that contradict the OI theory under realistic LTGC conditions, suggesting that K might be meaningless for LTGC engines.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessPerformance of Octane Index in Ltgc Engines from Beyond Mon to Beyond Ron
This work analyzes the ability of the Octane Index (OI) to characterize the autoignition resistance of gasoline-like fuels in a Low-Temperature Gasoline Combustion (LTGC) engine. Experimental studies in the Sandia LTGC engine at naturally aspirated ‘beyond-MON’ and high-boost ‘beyond-RON’ conditions showed that the correlation between OI and autoignition reactivity is poor. These experiments were successfully replicated in CHEMKIN, allowing detailed studies of the factors affecting the OI correlation. Systematic investigations were conducted to determine why the OI performs less well for LTGC combustion compared to end-gas autoignition (i.e. knock) in spark-ignition (SI) engines. A pseudo-MON condition that follows the pressure-temperature (P-T) trajectory of the real MON test was tested numerically, using 10 different fuels, leading to the conclusion that the OI correlation performs very well for an SI engine running at close-to-MON conditions. The effects of each difference between SI and LTGC combustion were then analyzed for four P-T trajectories: ‘beyond-MON’, ‘MON test’, ‘between RON-MON’, and ‘beyond-RON’ conditions. These differences included changes in: equivalence ratio, engine speed, and residence-time history along the P-T trajectory for piston-only compression, as used for LTGC, compared to compression by the piston plus flame propagation for SI combustion. For LTGC combustion, the OI correlation did not characterize the autoignition quality of gasoline-like fuels well for any P-T trajectory, but the factors causing this poor performance varied with conditions. For example, at naturally aspirated LTGC conditions (beyond-MON), changes in equivalence ratio were the primary cause, followed by differences in the P-T trajectory and changes in residence time. Whereas, for intake-boosted beyond-RON conditions, differences in the P-T trajectory had the largest effect, followed by changes in residence time. Finally, the parameter K that characterizes the OI correlation showed values that contradict the OI theory under realistic LTGC conditions, suggesting that K might be meaningless for LTGC engines.
- 22 September 2021
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 24 (1) , 217-239
Numerical investigation of soot emission sources in a direct-injection spark-ignition engine based on comprehensive breakup model validation
Direct injection system is widely adopted in spark-ignition engines to achieve higher thermal efficiency, but it accompanies a penalty in particulate emission, especially when engine is not fully warmed-up. Split injection strategy is known to be an effective measure to reduce engine-out particulate emissions. To better understand the role of split injections, this study aims to analyze the effect of split injection strategy on the sources of soot formation using computational fluid dynamics simulation. To accurately predict changes in particulate mass and number associated with split injection strategy, it is vital that spray models be carefully validated against the experimental data since spray dynamics govern the formation of soot emission sources, such as local fuel-rich mixtures and wall-deposited fuel-films. To this end, a set of spray experiments for free sprays is performed to measure liquid penetration length and droplet size distribution, and hence a comprehensive validation is conducted for spray breakup models. Then, engine simulations are carried out to predict the change in soot sources according to split injection, and the trend of simulation results is compared against the measured engine-out particulate mass and number. Simulation results indicate that breakup model validation using both penetration length and droplet size data is critical for predicting fuel spray dynamics and formation of sources of soot emission. It is also revealed that the piston wetting decreases as the number of injections increases because less amount of fuel is injected when piston is closer to the injector. Lastly, the late evaporation of heavy gasoline components from fuel-film appears to be a significant contributor to soot precursors formation.
- 22 September 2021
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 24 (1) , 217-239
Numerical investigation of soot emission sources in a direct-injection spark-ignition engine based on comprehensive breakup model validation
Direct injection system is widely adopted in spark-ignition engines to achieve higher thermal efficiency, but it accompanies a penalty in particulate emission, especially when engine is not fully warmed-up. Split injection strategy is known to be an effective measure to reduce engine-out particulate emissions. To better understand the role of split injections, this study aims to analyze the effect of split injection strategy on the sources of soot formation using computational fluid dynamics simulation. To accurately predict changes in particulate mass and number associated with split injection strategy, it is vital that spray models be carefully validated against the experimental data since spray dynamics govern the formation of soot emission sources, such as local fuel-rich mixtures and wall-deposited fuel-films. To this end, a set of spray experiments for free sprays is performed to measure liquid penetration length and droplet size distribution, and hence a comprehensive validation is conducted for spray breakup models. Then, engine simulations are carried out to predict the change in soot sources according to split injection, and the trend of simulation results is compared against the measured engine-out particulate mass and number. Simulation results indicate that breakup model validation using both penetration length and droplet size data is critical for predicting fuel spray dynamics and formation of sources of soot emission. It is also revealed that the piston wetting decreases as the number of injections increases because less amount of fuel is injected when piston is closer to the injector. Lastly, the late evaporation of heavy gasoline components from fuel-film appears to be a significant contributor to soot precursors formation.
- Open Access
- 1 August 2020
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 28 (8) , 583-589
Development of a Linkage System for Piston Measurement Using Downhill Simplex Method
- 1 August 2020
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 28 (8) , 583-589
Open AccessDevelopment of a Linkage System for Piston Measurement Using Downhill Simplex Method
- Open Access
A New Physics-Based Modeling Approach for a 0D Turbulence Model to Reflect the Intake Port and Chamber Geometries and the Corresponding Flow Structures in High-Tumble Spark-Ignition Engines
Turbulence is one of the most important aspects in spark-ignition engines as it can significantly affect burn rates, heat transfer rates, and combustion stability, and thus the performance. Turbulence originates from a large-scale mean motion that occurs during the induction process, which mainly consists of tumble motion in modern spark-ignition engines with a pentroof cylinder head. Despite its significance, most 0D turbulence models rely on calibration factors when calculating the evolution of tumble motion and its conversion into turbulence. In this study, the 0D tumble model has been improved based on the physical phenomena, as an attempt to develop a comprehensive model that predicts flow dynamics inside the cylinder. The generation and decay rates of tumble motion are expressed with regards of the flow structure in a realistic combustion chamber geometry, while the effects of port geometry on both charging efficiency and tumble generation rate are reflected by supplementary steady CFD. The developed tumble model was integrated with the standard k-ε model, and the new turbulence model has been validated with engine experimental data for various changes in operating conditions including engine speed, load, valve timing, and engine geometry. The calculated results showed a reasonable correlation with the measured combustion duration, verifying this physics-based model can properly predict turbulence characteristics without any additional calibration process. This model can suggest greater insights on engine operation and is expected to assist the optimization process of engine design and operating strategies.
Open AccessA New Physics-Based Modeling Approach for a 0D Turbulence Model to Reflect the Intake Port and Chamber Geometries and the Corresponding Flow Structures in High-Tumble Spark-Ignition Engines
Turbulence is one of the most important aspects in spark-ignition engines as it can significantly affect burn rates, heat transfer rates, and combustion stability, and thus the performance. Turbulence originates from a large-scale mean motion that occurs during the induction process, which mainly consists of tumble motion in modern spark-ignition engines with a pentroof cylinder head. Despite its significance, most 0D turbulence models rely on calibration factors when calculating the evolution of tumble motion and its conversion into turbulence. In this study, the 0D tumble model has been improved based on the physical phenomena, as an attempt to develop a comprehensive model that predicts flow dynamics inside the cylinder. The generation and decay rates of tumble motion are expressed with regards of the flow structure in a realistic combustion chamber geometry, while the effects of port geometry on both charging efficiency and tumble generation rate are reflected by supplementary steady CFD. The developed tumble model was integrated with the standard k-ε model, and the new turbulence model has been validated with engine experimental data for various changes in operating conditions including engine speed, load, valve timing, and engine geometry. The calculated results showed a reasonable correlation with the measured combustion duration, verifying this physics-based model can properly predict turbulence characteristics without any additional calibration process. This model can suggest greater insights on engine operation and is expected to assist the optimization process of engine design and operating strategies.
- 2 April 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Effects of Bore-to-Stroke Ratio on the Efficiency and Knock Characteristics in a Single-Cylinder GDI Engine
As a result of stringent global regulations on fuel economy and CO2 emissions, the development of high-efficiency SI engines is more urgent now than ever before. Along with advanced techniques in friction reduction, many researchers endeavor to decrease the B/S (bore-to-stroke) ratio from 1.0 (square) to a certain value, which is expected to reduce the heat loss and enhance the burning rate of SI engines. In this study, the effects of B/S ratios were investigated in aspects of efficiency and knock characteristics using a single-cylinder LIVC (late intake valve closing) GDI (gasoline direct injection) engine. Three B/S ratios (0.68, 0.83 and 1.00) were tested under the same mechanical compression ratio of 12:1 and the same displacement volume of 0.5 L. The head tumble ratio was maintained at the same level to solely investigate the effects of geometrical changes caused by variations in the B/S ratio. In addition, because the engine was equipped with a dual CVVT (continuous variable valve timing) system, the valve timings were optimized to fully exploit the potential of each geometry. As a result, lower bore-to-stroke ratios apparently exhibited higher knock resistances not only because of faster burn speeds but also because of the advantage of low unburned gas temperatures under the same valve timing in high-load conditions. However, it was shown that the advantage of a shorter burn duration did not substantially increase as the B/S ratio was decreased below 0.83. Among the tested operating conditions, especially in part load condition, the best efficiency under optimized valve timing was achieved at a B/S ratio of 0.83 because of the paradoxical increase in heat transfer loss observed in lower B/S ratios.
- 2 April 2019
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Effects of Bore-to-Stroke Ratio on the Efficiency and Knock Characteristics in a Single-Cylinder GDI Engine
As a result of stringent global regulations on fuel economy and CO2 emissions, the development of high-efficiency SI engines is more urgent now than ever before. Along with advanced techniques in friction reduction, many researchers endeavor to decrease the B/S (bore-to-stroke) ratio from 1.0 (square) to a certain value, which is expected to reduce the heat loss and enhance the burning rate of SI engines. In this study, the effects of B/S ratios were investigated in aspects of efficiency and knock characteristics using a single-cylinder LIVC (late intake valve closing) GDI (gasoline direct injection) engine. Three B/S ratios (0.68, 0.83 and 1.00) were tested under the same mechanical compression ratio of 12:1 and the same displacement volume of 0.5 L. The head tumble ratio was maintained at the same level to solely investigate the effects of geometrical changes caused by variations in the B/S ratio. In addition, because the engine was equipped with a dual CVVT (continuous variable valve timing) system, the valve timings were optimized to fully exploit the potential of each geometry. As a result, lower bore-to-stroke ratios apparently exhibited higher knock resistances not only because of faster burn speeds but also because of the advantage of low unburned gas temperatures under the same valve timing in high-load conditions. However, it was shown that the advantage of a shorter burn duration did not substantially increase as the B/S ratio was decreased below 0.83. Among the tested operating conditions, especially in part load condition, the best efficiency under optimized valve timing was achieved at a B/S ratio of 0.83 because of the paradoxical increase in heat transfer loss observed in lower B/S ratios.