Viveksheel Rajput
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Viveksheel Rajput has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Mudimallana Goud
Punjab Engineering College
14 shared publicationsNarendra Mohan Suri
Punjab Engineering College
13 shared publicationsSarbjit Singh
Mechanical Engineering Department, Punjab Engineering College, Chandigarh, India
3 shared publicationsSuman Kant
Punjab Engineering College
3 shared publicationsGanga Ram Chaudhary
SAIF/CIL, Panjab University, Chandigarh, India
2 shared publicationsJasdeep Bhinder
École de technologie supérieure ÉTS
2 shared publications
Latest Publications
- 2 January 2026
- Published by Springer Nature
- p. 213-222
Applications of the Ergonomics for Healthcare Workers: Systematic Review
- 2 January 2026
- Published by Springer Nature
- p. 213-222
Applications of the Ergonomics for Healthcare Workers: Systematic Review
- 8 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (23) , 29040-29059
Enhancing Silicon Carbide Powder Mixed Rotary Electrical Discharge Machining Performance during Monel 400 Machining: Novel Combination
- 8 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (23) , 29040-29059
Enhancing Silicon Carbide Powder Mixed Rotary Electrical Discharge Machining Performance during Monel 400 Machining: Novel Combination
- Open Access
- 18 February 2025
- Published by IEOM Society International
WEDM Process Parameters Investigation on the Concave Profile of Ti Implant Material Using the Desirability Approach
WEDM is used chiefly for machining Titanium and its alloys with good dimensional accuracy and surface finish. The research work has been done with the BBD of the RSM technique, and further multi-response optimization was done through the desirability function. The results of the research work shows that the effect of input variables pulse on-time (POT), pulse off-time (POFT,) spark gap voltage (SGV), and concave profile radius (CPR) on the output variables surface roughness (SR), and geometric error (GE) have been investigated. It observed that POT is the primary significant factor affecting the SR, and GE. With increases in CPR, Geometric error also increases. CPR is the most critical factor for the geometric error, with an 82.83% contribution. Experiment results also shows that POT and POFT significantly affected the surface integrity with the formation of pockmarks, overlapping craters, micro-cracks, and recast layer.WEDM is used chiefly for machining Titanium and its alloys with good dimensional accuracy and surface finish. The research work has been done with the BBD of the RSM technique, and further multi-response optimization was done through the desirability function. The results of the research work shows that the effect of input variables pulse on-time (POT), pulse off-time (POFT,) spark gap voltage (SGV), and concave profile radius (CPR) on the output variables surface roughness (SR), and geometric error (GE) have been investigated. It observed that POT is the primary significant factor affecting the SR, and GE. With increases in CPR, Geometric error also increases. CPR is the most critical factor for the geometric error, with an 82.83% contribution. Experiment results also shows that POT and POFT significantly affected the surface integrity with the formation of pockmarks, overlapping craters, micro-cracks, and recast layer.
- 18 February 2025
- Published by IEOM Society International
Open AccessWEDM Process Parameters Investigation on the Concave Profile of Ti Implant Material Using the Desirability Approach
WEDM is used chiefly for machining Titanium and its alloys with good dimensional accuracy and surface finish. The research work has been done with the BBD of the RSM technique, and further multi-response optimization was done through the desirability function. The results of the research work shows that the effect of input variables pulse on-time (POT), pulse off-time (POFT,) spark gap voltage (SGV), and concave profile radius (CPR) on the output variables surface roughness (SR), and geometric error (GE) have been investigated. It observed that POT is the primary significant factor affecting the SR, and GE. With increases in CPR, Geometric error also increases. CPR is the most critical factor for the geometric error, with an 82.83% contribution. Experiment results also shows that POT and POFT significantly affected the surface integrity with the formation of pockmarks, overlapping craters, micro-cracks, and recast layer.WEDM is used chiefly for machining Titanium and its alloys with good dimensional accuracy and surface finish. The research work has been done with the BBD of the RSM technique, and further multi-response optimization was done through the desirability function. The results of the research work shows that the effect of input variables pulse on-time (POT), pulse off-time (POFT,) spark gap voltage (SGV), and concave profile radius (CPR) on the output variables surface roughness (SR), and geometric error (GE) have been investigated. It observed that POT is the primary significant factor affecting the SR, and GE. With increases in CPR, Geometric error also increases. CPR is the most critical factor for the geometric error, with an 82.83% contribution. Experiment results also shows that POT and POFT significantly affected the surface integrity with the formation of pockmarks, overlapping craters, micro-cracks, and recast layer.
- 10 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (17) , 19312-19325
Investigation on Glass Material’s Hole Characteristics Using Different Tool Geometries in Cognitive Electrochemical Discharge Machining Process
- 10 February 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (17) , 19312-19325
Investigation on Glass Material’s Hole Characteristics Using Different Tool Geometries in Cognitive Electrochemical Discharge Machining Process
- 15 November 2023
- Published by Springer Nature
- p. 237-255
3D Finite Element Modelling of Ti–6Al–4V Using Powder Mixed EDM for Bio-Medical Applications
- 15 November 2023
- Published by Springer Nature
- p. 237-255
3D Finite Element Modelling of Ti–6Al–4V Using Powder Mixed EDM for Bio-Medical Applications
- 15 November 2023
- Published by Springer Nature
- p. 225-235
Development and Characterization of PLA Based Bio-Polymer for Bio-Medical Applications
- 15 November 2023
- Published by Springer Nature
- p. 225-235
Development and Characterization of PLA Based Bio-Polymer for Bio-Medical Applications
- 27 September 2023
- Published by Springer Nature
- p. 59-69
Research Progress of Self-Healing Elastomers Materials: Processing and Characterization
- 27 September 2023
- Published by Springer Nature
- p. 59-69
Research Progress of Self-Healing Elastomers Materials: Processing and Characterization
- 3 July 2023
- Published by Springer Nature in Silicon
- Vol. 15 (17) , 7279-7292
Development and Analysis of Polymer-Based Self-Healing Composite Embedded with Silica (SiO2) Hollow Glass Fibers
- 3 July 2023
- Published by Springer Nature in Silicon
- Vol. 15 (17) , 7279-7292
Development and Analysis of Polymer-Based Self-Healing Composite Embedded with Silica (SiO2) Hollow Glass Fibers