Jorge Rodriguez-Cuevas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jorge Rodriguez-Cuevas has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Alexander E. Martynyuk
División de Ingeniería Eléctrica, Facultad de Ingeniería, Universidad Nacional Autónoma de México, Mexico City, Mexico
24 shared publications - Jose Ismael Martinez-Lopez
División de Ingeniería Eléctrica, Facultad de Ingeniería, Universidad Nacional Autónoma de México, Mexico City, Mexico
22 shared publications - Rosalba Martinez-Lopez
División de Ingeniería Eléctrica, Facultad de Ingeniería, Universidad Nacional Autónoma de México, Mexico City, Mexico
4 shared publications - Lourdes Martinez-Lopez
Divisin de Ingeniera Elctrica, Facultad de Ingeniera, Universidad Nacional Autonoma de Mexico, Mexico City, Mexico
3 shared publications A.G. Martinez-Lopez
Universidad Politecnica de la Region Riberena, Col. Jardines de San German, Ciudad Miguel Aleman, Tamaulipas C.P. 88300, Mexico
2 shared publications- Henry Fabian-Gongora
Facultad de Ingeniería, Universidad Autónoma de Campeche, Campeche, México
2 shared publications
Latest Publications
- 19 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (3) , 2956-2961
Dual Circularly Polarized Millimeter-Wave Transmitarray
This communication reports the dual-circularly-polarized-high-aperture-efficiency transmitarrays (TAs) capable of forming patterns with two independent beams for the right-hand circularly-polarized wave (RHCPW) and left-hand circularly-polarized wave (LHCPW) at the same frequency. The five-layer TA elements contain a ring-slot resonator loaded by interdigital capacitors in each layer. The TA element was optimized as a three-bit phase shifter that adds two independent phase shifts to the transmitted RHCPW and LHCPW. The geometry of the TA element was validated by designing two 500-element TAs. At 36.5 GHz, these two TAs form RHCP beams in the directions (θ = 20°, ϕ = 0°) and (θ = 40°, ϕ = 0°), respectively, and the LHCP beams point in the direction (θ = 0°, ϕ = 0°) in both TAs. These two TAs were fabricated and tested. For the first TA, the measured gains were 27.7 dBi and 27.6 dBi for the RHCP and LHCP radiation patterns, respectively, with overall aperture efficiencies ηs of 0.46 and 0.45. The second TA demonstrated the measured gains of 27.0 dBi and 28.5 dBi for the RHCPW and LHCPW, respectively, with ηs equal to 0.39 and 0.55. The measured cross-polarization levels in the direction of pattern maximums were -21.1 dB, -24.4 dB for the first TA, and -15.0 dB, -31.2 dB for the second RA, considering RHCPW and LHCPW beams, respectively.
- 19 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (3) , 2956-2961
Dual Circularly Polarized Millimeter-Wave Transmitarray
This communication reports the dual-circularly-polarized-high-aperture-efficiency transmitarrays (TAs) capable of forming patterns with two independent beams for the right-hand circularly-polarized wave (RHCPW) and left-hand circularly-polarized wave (LHCPW) at the same frequency. The five-layer TA elements contain a ring-slot resonator loaded by interdigital capacitors in each layer. The TA element was optimized as a three-bit phase shifter that adds two independent phase shifts to the transmitted RHCPW and LHCPW. The geometry of the TA element was validated by designing two 500-element TAs. At 36.5 GHz, these two TAs form RHCP beams in the directions (θ = 20°, ϕ = 0°) and (θ = 40°, ϕ = 0°), respectively, and the LHCP beams point in the direction (θ = 0°, ϕ = 0°) in both TAs. These two TAs were fabricated and tested. For the first TA, the measured gains were 27.7 dBi and 27.6 dBi for the RHCP and LHCP radiation patterns, respectively, with overall aperture efficiencies ηs of 0.46 and 0.45. The second TA demonstrated the measured gains of 27.0 dBi and 28.5 dBi for the RHCPW and LHCPW, respectively, with ηs equal to 0.39 and 0.55. The measured cross-polarization levels in the direction of pattern maximums were -21.1 dB, -24.4 dB for the first TA, and -15.0 dB, -31.2 dB for the second RA, considering RHCPW and LHCPW beams, respectively.
- 29 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 21 (11) , 1218-1226
In-line Wideband RF MEMS Switch Integrated on PCB Using BCB Planarization
In this paper, the design, fabrication, and characterization of a wideband cantilever RF-MEMS coplanar line switch with metal-to-metal contact are presented. Printed circuit board (PCB) processing techniques and benzocyclobutene (BCB) as planarization material were used to integrate the RFMEMS switch to a microwave-friendly substrate. The proposed fabrication process was developed at low-temperature (< 210 C) and combines layers of BCB, photoresist and copper. The process is relatively simple, comparatively inexpensive, and it implies a wide usage of BCB as planarization material to reduce the surface roughness of the cantilever beam, enabling a high repeatability of the fabricated MEMS switches. This low-cost fabrication process was used to develop a switch with low actuation voltage, and acceptable levels of insertion loss and isolation in the frequency band from DC to 20 GHz. The fabricated switch demonstrated isolation higher than 13.1 dB and insertion loss lower than 0.63 dB in the frequency range from DC up to 12 GHz. In frequencies from 12 to 20 GHz, the insertion loss is lower than 1.16 dB and the isolation is higher than 9.6 dB. The pull-in voltage was 30 V with measured commutation time of 425 s. This RF-MEMS switch is suitable to be monolithically integrated with printed circuits on flexible microwave-friendly substrates.
- 29 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 21 (11) , 1218-1226
In-line Wideband RF MEMS Switch Integrated on PCB Using BCB Planarization
In this paper, the design, fabrication, and characterization of a wideband cantilever RF-MEMS coplanar line switch with metal-to-metal contact are presented. Printed circuit board (PCB) processing techniques and benzocyclobutene (BCB) as planarization material were used to integrate the RFMEMS switch to a microwave-friendly substrate. The proposed fabrication process was developed at low-temperature (< 210 C) and combines layers of BCB, photoresist and copper. The process is relatively simple, comparatively inexpensive, and it implies a wide usage of BCB as planarization material to reduce the surface roughness of the cantilever beam, enabling a high repeatability of the fabricated MEMS switches. This low-cost fabrication process was used to develop a switch with low actuation voltage, and acceptable levels of insertion loss and isolation in the frequency band from DC to 20 GHz. The fabricated switch demonstrated isolation higher than 13.1 dB and insertion loss lower than 0.63 dB in the frequency range from DC up to 12 GHz. In frequencies from 12 to 20 GHz, the insertion loss is lower than 1.16 dB and the isolation is higher than 9.6 dB. The pull-in voltage was 30 V with measured commutation time of 425 s. This RF-MEMS switch is suitable to be monolithically integrated with printed circuits on flexible microwave-friendly substrates.
- Open Access
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 105564-105576
Independently Tunable Closely Spaced Triband Frequency Selective Surface Unit Cell Using the Third Resonant Mode of Split Ring Slots
In this paper, a tunable triband frequency selective surface unit cell based on varactor-loaded split ring slots is presented. By using the third resonant mode, a considerable mutual coupling reduction between adjacent ring slots is obtained ensuring both close band response as well as independent band tuning. Simulated results show the tunable properties of the proposed approach by shifting the three passbands resonant frequencies from 8.368, 10.276, and 12.010 GHz (for the unloaded split ring slots), to 7.732, 9.202, and 10.900 GHz, respectively, when each split ring slot is loaded with a capacitance of 140 fF. Furthermore, the metal shorts that split the ring slots as well as the metal rings located in between the slots are used to build the conducting paths to bias each varactor with minimum disruption in the RF response. A demonstrator based on an X-band diaphragm was designed, fabricated, and experimentally tested. Measured results using a varactor with capacitance range of 30-65 fF show resonant frequencies for the unbiased varactors at 8.53, 9.70 and 11.47 GHz with insertion loss of 1.1, 2.3 and 2.4 dB, respectively, while biasing the diodes at maximum reverse voltages (24 V) provides resonant frequencies at 8.74, 10.03 and 11.77 GHz with insertion loss of 0.8, 1.4 and 1.7 dB, respectively. Frequency shifts of 210, 330 and 300 MHz for the first, second and third resonant frequencies were obtained, respectively. The -10 dB reflection coefficient bandwidths were 495 MHz for the first band, 436 MHz for the second band and 418 MHz for the third band. Close band response is verified obtaining frequency band ratios of 1.18 and 1.14 for the third to the second resonance, and for the second to the first resonance, respectively.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 105564-105576
Open AccessIndependently Tunable Closely Spaced Triband Frequency Selective Surface Unit Cell Using the Third Resonant Mode of Split Ring Slots
In this paper, a tunable triband frequency selective surface unit cell based on varactor-loaded split ring slots is presented. By using the third resonant mode, a considerable mutual coupling reduction between adjacent ring slots is obtained ensuring both close band response as well as independent band tuning. Simulated results show the tunable properties of the proposed approach by shifting the three passbands resonant frequencies from 8.368, 10.276, and 12.010 GHz (for the unloaded split ring slots), to 7.732, 9.202, and 10.900 GHz, respectively, when each split ring slot is loaded with a capacitance of 140 fF. Furthermore, the metal shorts that split the ring slots as well as the metal rings located in between the slots are used to build the conducting paths to bias each varactor with minimum disruption in the RF response. A demonstrator based on an X-band diaphragm was designed, fabricated, and experimentally tested. Measured results using a varactor with capacitance range of 30-65 fF show resonant frequencies for the unbiased varactors at 8.53, 9.70 and 11.47 GHz with insertion loss of 1.1, 2.3 and 2.4 dB, respectively, while biasing the diodes at maximum reverse voltages (24 V) provides resonant frequencies at 8.74, 10.03 and 11.77 GHz with insertion loss of 0.8, 1.4 and 1.7 dB, respectively. Frequency shifts of 210, 330 and 300 MHz for the first, second and third resonant frequencies were obtained, respectively. The -10 dB reflection coefficient bandwidths were 495 MHz for the first band, 436 MHz for the second band and 418 MHz for the third band. Close band response is verified obtaining frequency band ratios of 1.18 and 1.14 for the third to the second resonance, and for the second to the first resonance, respectively.
- Open Access
- 12 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 57886-57896
Close Band Spacing Pentaband Frequency Selective Surfaces Based on Concentric Ring Slots
This paper presents a polarization insensitive frequency selective surface (FSS) based on concentric ring slots with five closely spaced passbands. The proposed FSS unit cell contains five ring slots coupled with a supplementary innermost ring slot. The close band response within the first five transmission bands is achieved by the influence of the modified geometry obtained with the inclusion of the sixth ring slot. This added ring slot causes the appearance of a stopband, due to the conductive ring between the fifth and the sixth ring apertures, and a passband produced inherently by the sixth ring aperture. The effect of the additional stopband and passband in the FSS response has been investigated in the paper. Full-wave simulations reveal that a modified geometry with proper sizes effectively enables the close band response of the pentaband FSS. To validate the proposed approach, a 729-element penta-bandpass FSS prototype operating at millimeter-wave frequencies has been designed, fabricated, and tested. Experimental results in a free-space measurement setup indicate resonances at f 1 = 26.7, f 2 = 29.8, f 3 = 33.6, f 4 = 38.1, and f 5 = 44.2 GHz, with resonant frequency ratios of f 2 / f 1 = 1.12, f 3 / f 2 = 1.13, f 4 / f 3 = 1.13, and f 5 / f 4 = 1.16. This FSS demonstrates an extremely low ratio of the highest and the lowest resonant frequencies ( f 5 / f 1 = 1.66) for a penta-band operation. This polarization insensitive FSS demonstrates good performance at oblique angular incidence for elevation angles up to 45°.
- 12 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 57886-57896
Open AccessClose Band Spacing Pentaband Frequency Selective Surfaces Based on Concentric Ring Slots
This paper presents a polarization insensitive frequency selective surface (FSS) based on concentric ring slots with five closely spaced passbands. The proposed FSS unit cell contains five ring slots coupled with a supplementary innermost ring slot. The close band response within the first five transmission bands is achieved by the influence of the modified geometry obtained with the inclusion of the sixth ring slot. This added ring slot causes the appearance of a stopband, due to the conductive ring between the fifth and the sixth ring apertures, and a passband produced inherently by the sixth ring aperture. The effect of the additional stopband and passband in the FSS response has been investigated in the paper. Full-wave simulations reveal that a modified geometry with proper sizes effectively enables the close band response of the pentaband FSS. To validate the proposed approach, a 729-element penta-bandpass FSS prototype operating at millimeter-wave frequencies has been designed, fabricated, and tested. Experimental results in a free-space measurement setup indicate resonances at f 1 = 26.7, f 2 = 29.8, f 3 = 33.6, f 4 = 38.1, and f 5 = 44.2 GHz, with resonant frequency ratios of f 2 / f 1 = 1.12, f 3 / f 2 = 1.13, f 4 / f 3 = 1.13, and f 5 / f 4 = 1.16. This FSS demonstrates an extremely low ratio of the highest and the lowest resonant frequencies ( f 5 / f 1 = 1.66) for a penta-band operation. This polarization insensitive FSS demonstrates good performance at oblique angular incidence for elevation angles up to 45°.
- Open Access
- 5 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 6990-6999
A Dual Circularly-Polarized Multilayer Reflective Surface Based on Loaded Ring Slots
In this paper, a dual circularly-polarized multilayer reflective surface (MRS) based on loaded ring-slots for reflectarray applications is presented. The MRS comprises a wideband multilayer circular polarizer cascaded with a multilayer reflective screen with independent phase shifting properties for the two orthogonal linearly polarized components. The first polarization conversion is accomplished by a four-layer polarizer based on periodic arrays of bisected split rings that converts two incident circularly-polarized waves, one left-handed (LHCPW) and other right-handed (RHCPW), into two linearly polarized waves with orthogonal polarization planes. These two waves can be phase-shifted independently by a periodic two-layer array of specially designed reflective elements. Each element consists of a ring-slot resonator loaded with two pairs of reactances orthogonally located that can be varied to obtain two linear reflection phase tapers along the array. These reflected waves are then transformed back by the polarizer into two circularly polarized waves traveling into the desired directions. To validate the proposed approach, a six-layer prototype operating at 32 GHz that provides reflection elevation and azimuthal angles for the RHCPW at 22° and 180°, respectively, and reflection elevation and azimuthal angles for the LHCPW at 18° and 0°, respectively, has been designed, fabricated, and experimentally verified.
- 5 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 6990-6999
Open AccessA Dual Circularly-Polarized Multilayer Reflective Surface Based on Loaded Ring Slots
In this paper, a dual circularly-polarized multilayer reflective surface (MRS) based on loaded ring-slots for reflectarray applications is presented. The MRS comprises a wideband multilayer circular polarizer cascaded with a multilayer reflective screen with independent phase shifting properties for the two orthogonal linearly polarized components. The first polarization conversion is accomplished by a four-layer polarizer based on periodic arrays of bisected split rings that converts two incident circularly-polarized waves, one left-handed (LHCPW) and other right-handed (RHCPW), into two linearly polarized waves with orthogonal polarization planes. These two waves can be phase-shifted independently by a periodic two-layer array of specially designed reflective elements. Each element consists of a ring-slot resonator loaded with two pairs of reactances orthogonally located that can be varied to obtain two linear reflection phase tapers along the array. These reflected waves are then transformed back by the polarizer into two circularly polarized waves traveling into the desired directions. To validate the proposed approach, a six-layer prototype operating at 32 GHz that provides reflection elevation and azimuthal angles for the RHCPW at 22° and 180°, respectively, and reflection elevation and azimuthal angles for the LHCPW at 18° and 0°, respectively, has been designed, fabricated, and experimentally verified.
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 18 (09) , 1656-1663
Low-Loss Polarization-Agile U-Band Switch
A low-loss U-band polarization-agile single pole single throw (SPST) circular waveguide switch with filtering capability is presented. This switch contains a diaphragm based on a ring slot with p-i-n diode switchable radial stubs situated at the cross-section of a circular waveguide. Commutation of the p-i-n diodes permits the control of the transmission characteristics for the incident linearly polarized wave with different orientations of its polarization vector. Due to the application of an original hybrid technology for the diaphragm fabrication, an insertion loss of 0.45 dB and an isolation of 20.6 dB are obtained near the central frequency of 50.0 GHz. The developed SPST switch is suitable for the usage in the antenna block of modern millimeter-wave receivers with polarization reuse due to the ultra-low insertion loss..
- 1 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 18 (09) , 1656-1663
Low-Loss Polarization-Agile U-Band Switch
A low-loss U-band polarization-agile single pole single throw (SPST) circular waveguide switch with filtering capability is presented. This switch contains a diaphragm based on a ring slot with p-i-n diode switchable radial stubs situated at the cross-section of a circular waveguide. Commutation of the p-i-n diodes permits the control of the transmission characteristics for the incident linearly polarized wave with different orientations of its polarization vector. Due to the application of an original hybrid technology for the diaphragm fabrication, an insertion loss of 0.45 dB and an isolation of 20.6 dB are obtained near the central frequency of 50.0 GHz. The developed SPST switch is suitable for the usage in the antenna block of modern millimeter-wave receivers with polarization reuse due to the ultra-low insertion loss..
- 3 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (6) , 4668-4676
Miniaturized Frequency-Selective Surfaces Based on Monolithically Integrated Components
In this paper, a novel approach to design low profile miniaturized frequency selective surfaces (FSSs) is proposed. The effective miniaturization of the FSS elements, based on square-ring-slot resonators, is accomplished by reactively loading the FSS unit cell with monolithically integrated components. The reactive components, such as capacitors and inductors embedded in the resonant unit cell, are fabricated using a multistep thin-film process based on benzocyclobutene (BCB) resin. The capacitors are built as planar metal-insulator-metal structures using an ultra-thin dielectric layer of BCB, while the multiturn inductors are fabricated as planar spiral structures with two metal layers and BCB as an interlevel dielectric for crossover. The advantages of the proposed approach are the capability to obtain large values of capacitances and inductances within small areas with low parasitics as well as the benefits in cost reduction and easy fabrication by using a planar microfabrication process. A component value variation analysis is performed to study the effect of fabrication tolerances in the reflection and transmission coefficients of the FSS when non-identical small cells are obtained. It has been experimentally validated that a 2.46-mm unit cell resonates at 4.175 GHz with transmission loss of 0.86 dB, achieving a miniaturization level of λ/29.
- 3 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68 (6) , 4668-4676
Miniaturized Frequency-Selective Surfaces Based on Monolithically Integrated Components
In this paper, a novel approach to design low profile miniaturized frequency selective surfaces (FSSs) is proposed. The effective miniaturization of the FSS elements, based on square-ring-slot resonators, is accomplished by reactively loading the FSS unit cell with monolithically integrated components. The reactive components, such as capacitors and inductors embedded in the resonant unit cell, are fabricated using a multistep thin-film process based on benzocyclobutene (BCB) resin. The capacitors are built as planar metal-insulator-metal structures using an ultra-thin dielectric layer of BCB, while the multiturn inductors are fabricated as planar spiral structures with two metal layers and BCB as an interlevel dielectric for crossover. The advantages of the proposed approach are the capability to obtain large values of capacitances and inductances within small areas with low parasitics as well as the benefits in cost reduction and easy fabrication by using a planar microfabrication process. A component value variation analysis is performed to study the effect of fabrication tolerances in the reflection and transmission coefficients of the FSS when non-identical small cells are obtained. It has been experimentally validated that a 2.46-mm unit cell resonates at 4.175 GHz with transmission loss of 0.86 dB, achieving a miniaturization level of λ/29.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Active Frequency Selective Surfaces Based on Loaded Ring Patches
This paper presents an X-band active frequency selective surface (FSS) based on metal rings loaded with varactor diodes. The FSS unit cell that contains the loaded metal ring resonator is modeled using both an equivalent electrical circuit and a commercially-available full-wave solver. The resonant frequency of the ring is tuned by changing the varactor's capacitance due to the different reverse-bias voltages applied to the varactor diodes. It is shown that these capacitor values in the range from 30 to 65 pF shift the resonant frequency of the FSS from 9.17 to 8.33 GHz. The proposed geometry can be used as an electronically-tunable band-stop FSS.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Active Frequency Selective Surfaces Based on Loaded Ring Patches
This paper presents an X-band active frequency selective surface (FSS) based on metal rings loaded with varactor diodes. The FSS unit cell that contains the loaded metal ring resonator is modeled using both an equivalent electrical circuit and a commercially-available full-wave solver. The resonant frequency of the ring is tuned by changing the varactor's capacitance due to the different reverse-bias voltages applied to the varactor diodes. It is shown that these capacitor values in the range from 30 to 65 pF shift the resonant frequency of the FSS from 9.17 to 8.33 GHz. The proposed geometry can be used as an electronically-tunable band-stop FSS.
- 8 March 2017
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 31 (6) , 561-576
Spiraphase-type leaky-wave structure
A leaky-wave structure (LWS) based on two stacked spiraphase-type reflectarrays (RAs) is analysed in this paper. Each RA contains capacitively loaded ring slot elements arranged at the nodes of a square periodic grid. The proposed LWS performs frequency scanning of a conical beam by changing the cone aperture angle 2θ0. Furthermore, the reconfiguration of the radiation pattern can be achieved by rotating the RA elements. Four Ka-band LWSs with different angular positions of the capacitive loads at the top RA were designed, fabricated and tested to demonstrate the pattern reconfiguration capability. A full-wave mathematical model was used to optimize the reflectarray elements and a simplified mathematical model was developed to predict the radiation characteristics of the whole structure. It was experimentally proven that frequency sweep from 36.37 to 39.9 GHz leads to the change of the angle θ0 from 0° to 38°. The increment of θ0 from 0° to 23° at 36.4 GHz was observed, when the reactive loads of the ring-slot elements at the top RA were rotated on the angle 18°. Good agreement between theoretical predictions and measurements was observed.
- 8 March 2017
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 31 (6) , 561-576
Spiraphase-type leaky-wave structure
A leaky-wave structure (LWS) based on two stacked spiraphase-type reflectarrays (RAs) is analysed in this paper. Each RA contains capacitively loaded ring slot elements arranged at the nodes of a square periodic grid. The proposed LWS performs frequency scanning of a conical beam by changing the cone aperture angle 2θ0. Furthermore, the reconfiguration of the radiation pattern can be achieved by rotating the RA elements. Four Ka-band LWSs with different angular positions of the capacitive loads at the top RA were designed, fabricated and tested to demonstrate the pattern reconfiguration capability. A full-wave mathematical model was used to optimize the reflectarray elements and a simplified mathematical model was developed to predict the radiation characteristics of the whole structure. It was experimentally proven that frequency sweep from 36.37 to 39.9 GHz leads to the change of the angle θ0 from 0° to 38°. The increment of θ0 from 0° to 23° at 36.4 GHz was observed, when the reactive loads of the ring-slot elements at the top RA were rotated on the angle 18°. Good agreement between theoretical predictions and measurements was observed.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 775-776
Switchable ring slot frequency selective surfaces with low-disruptive bias circuits
Active frequency selective surfaces based on PIN diode switchable ring slots with low-disruptive bias circuits are investigated. An active diaphragm was measured through the waveguide simulator in X-band. The proposed surface can provide two states of operation and can be used for the effective control of the electromagnetic wave transmission.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 775-776
Switchable ring slot frequency selective surfaces with low-disruptive bias circuits
Active frequency selective surfaces based on PIN diode switchable ring slots with low-disruptive bias circuits are investigated. An active diaphragm was measured through the waveguide simulator in X-band. The proposed surface can provide two states of operation and can be used for the effective control of the electromagnetic wave transmission.