Anton Korol
Anton Korol has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Yevgen Podkopayev
Limited Liability Company Manufacturing Company ELTEKO
3 shared publications - Yuliia Simonova
State Higher Education Establishment «Donetsk National Technical University
3 shared publications - Andriy Petrenko
Donetsk National Technical University
2 shared publications Anton Polozhiy
2 shared publicationsDonetsk National Technical University
2 shared publicationsIgor Iordanov
2 shared publications
Latest Publications
- 1 January 2022
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- No. 1
STRUCTURING EXPERIMENTAL DATA ON THE PERFORMANCE OF ARCH SUPPORTS FOR PROBABILISTIC ASSESSMENT OF THE STATE OF RETRACTABLE DRIFTS
Purpose. Structuring of experimental data of mine observations of the performance of arched flexible supports to establish a probabilistic assessment of the state of haulage drifts of steep coal seams in the excavation areas of a coal mine. Methods. The methodological basis of the research is an integrated approach, including the analysis and generalization of scientific achievements on the problem under study; mine observations of the state of development workings; analytical calculations using the basic provisions of probability theory, mathematical statistics using differential equations. Results. A probabilistic assessment of the state of the haulage drift under different protection methods, used to predict the stability of section development workings, was obtained from the experimental data of mine observations (observation time t = 4280 hours) of the performance of the arched pliable lining installed in the working along the length of the excavation section. After the sample was formed, the calculation of a statistical assessment of the reliability of the support operation was performed: the indicators of the failure rate λ and the recovery rate μ were established. Dependencies are obtained that allow assessing the state of development workings along the length of the excavation section and in the zone of influence of the stopping operations. It is proved that in the steady mode of operation of the haulage drift, with an increase in the failure rate of the arch support by 5 times, the availability factor, as a function of the reliability and maintainability of the support, changes from 0.9 to 0.5, which leads to a deterioration in time, approximately by 60 %, operational characteristics of the support in the supported development. Novelty. The probabilistic assessment of the loss of stability of the haulage drift along the length of the excavation section is based on the structuring of the data on the performance of arched supports and depends on the method of protection of the working, the intensity of failures of the arched supple support and the frequency of its damage, when in the desired interval of observations when forming the sample, the position of the stopping front is taken into account. Practical relevance. For the reuse of development workings with a store method of preparing steep seams and a descending order of mining floors, a conceptual model is proposed that allows predicting the state of haulage drifts along the length of the excavation area, taking into account the method of protection.
- 1 January 2022
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- No. 1
STRUCTURING EXPERIMENTAL DATA ON THE PERFORMANCE OF ARCH SUPPORTS FOR PROBABILISTIC ASSESSMENT OF THE STATE OF RETRACTABLE DRIFTS
Purpose. Structuring of experimental data of mine observations of the performance of arched flexible supports to establish a probabilistic assessment of the state of haulage drifts of steep coal seams in the excavation areas of a coal mine. Methods. The methodological basis of the research is an integrated approach, including the analysis and generalization of scientific achievements on the problem under study; mine observations of the state of development workings; analytical calculations using the basic provisions of probability theory, mathematical statistics using differential equations. Results. A probabilistic assessment of the state of the haulage drift under different protection methods, used to predict the stability of section development workings, was obtained from the experimental data of mine observations (observation time t = 4280 hours) of the performance of the arched pliable lining installed in the working along the length of the excavation section. After the sample was formed, the calculation of a statistical assessment of the reliability of the support operation was performed: the indicators of the failure rate λ and the recovery rate μ were established. Dependencies are obtained that allow assessing the state of development workings along the length of the excavation section and in the zone of influence of the stopping operations. It is proved that in the steady mode of operation of the haulage drift, with an increase in the failure rate of the arch support by 5 times, the availability factor, as a function of the reliability and maintainability of the support, changes from 0.9 to 0.5, which leads to a deterioration in time, approximately by 60 %, operational characteristics of the support in the supported development. Novelty. The probabilistic assessment of the loss of stability of the haulage drift along the length of the excavation section is based on the structuring of the data on the performance of arched supports and depends on the method of protection of the working, the intensity of failures of the arched supple support and the frequency of its damage, when in the desired interval of observations when forming the sample, the position of the stopping front is taken into account. Practical relevance. For the reuse of development workings with a store method of preparing steep seams and a descending order of mining floors, a conceptual model is proposed that allows predicting the state of haulage drifts along the length of the excavation area, taking into account the method of protection.
- 1 January 2021
- Published by Donetsk National Technical University in SCIENTIFIC PAPERS OF DONNTU Series: “The Mining and Geology”
ASSESSMENT OF STABILITY OF THE ROOF IN THE CARBON ART, WHICH CONTAINS PRODUCTS DURING THE DEVELOPMENT OF HARD COAL LAYERS
Purpose. Estimation of stability of a roof of a steep coal seam in the coal massif for maintenance of an operational condition of mine workings. Methods. To achieve this goal, analytical studies were performed using the basic principles of classical mechanics, the theory of elasticity and resistance of materials, when the roof of the coal seam was studied in the form of a model of a beam with a support. Results. As a result of the performed researches it is established that for an inclined single-girder beam with supports, at any regularity of distribution of loading on a surface the maximum deflection around the middle of span within (0,48 – 0,579) length of a beam is fixed. The value of the maximum deflection of the deformed load-bearing element depends on the angle of inclination and the ratio of the linear dimensions of the simulated beam. The curved axis is not perfectly symmetrical about the middle of the beam. The deviation from the symmetry depends on the linear dimensions of the model, the angle of inclination and is determined by the direction of the vector of total displacement of the beam. The deviation from the symmetry depends on the linear dimensions of the model, the angle of inclination and is determined by the direction of the vector of total displacement of the beam. The area in which the loss of stability of the load-bearing element is possible, occupies about 10% of the length of the inclined beam. In the presence of an asymmetrical deflection, to avoid loss of stability of the model, the placement of the system of supporting supports is advisable in this area of the beam. Scientific novelty. For the roof of a steep coal seam in its modeling in the form of an inclined single-girder beam with supports, when the external load is distributed on the surface naturally, the direction of the vector of complete displacement of the loaded model determines the contour of the curved axis of the deformed load-bearing element. Practical significance. The stability of the lateral rocks of the steep coal seam, which determines the operational condition of the mine workings in the coal massif, is provided by a system of supporting supports, the deformation characteristics of which are determined by the predicted deflection of the roof in the produced space. Keywords: stability, lateral rocks, coal massif, mining, deflection, supporting support.
- 1 January 2021
- Published by Donetsk National Technical University in SCIENTIFIC PAPERS OF DONNTU Series: “The Mining and Geology”
ASSESSMENT OF STABILITY OF THE ROOF IN THE CARBON ART, WHICH CONTAINS PRODUCTS DURING THE DEVELOPMENT OF HARD COAL LAYERS
Purpose. Estimation of stability of a roof of a steep coal seam in the coal massif for maintenance of an operational condition of mine workings. Methods. To achieve this goal, analytical studies were performed using the basic principles of classical mechanics, the theory of elasticity and resistance of materials, when the roof of the coal seam was studied in the form of a model of a beam with a support. Results. As a result of the performed researches it is established that for an inclined single-girder beam with supports, at any regularity of distribution of loading on a surface the maximum deflection around the middle of span within (0,48 – 0,579) length of a beam is fixed. The value of the maximum deflection of the deformed load-bearing element depends on the angle of inclination and the ratio of the linear dimensions of the simulated beam. The curved axis is not perfectly symmetrical about the middle of the beam. The deviation from the symmetry depends on the linear dimensions of the model, the angle of inclination and is determined by the direction of the vector of total displacement of the beam. The deviation from the symmetry depends on the linear dimensions of the model, the angle of inclination and is determined by the direction of the vector of total displacement of the beam. The area in which the loss of stability of the load-bearing element is possible, occupies about 10% of the length of the inclined beam. In the presence of an asymmetrical deflection, to avoid loss of stability of the model, the placement of the system of supporting supports is advisable in this area of the beam. Scientific novelty. For the roof of a steep coal seam in its modeling in the form of an inclined single-girder beam with supports, when the external load is distributed on the surface naturally, the direction of the vector of complete displacement of the loaded model determines the contour of the curved axis of the deformed load-bearing element. Practical significance. The stability of the lateral rocks of the steep coal seam, which determines the operational condition of the mine workings in the coal massif, is provided by a system of supporting supports, the deformation characteristics of which are determined by the predicted deflection of the roof in the produced space. Keywords: stability, lateral rocks, coal massif, mining, deflection, supporting support.
- 1 January 2021
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- No. 1
SUBSTANTIATION FOR SIMPLIFICATION OF CALCULATION MODELS FOR ASSESSMENT OF THE STABILITY OF ROOF ROCKS
Purpose. Substantiation of expediency and admissibility of use of the simplified calculation models of a coal seam roof for an estimation of its stability under the action of external loadings. Methods. To achieve this purpose, the studies have been performed using the basic principles of the theory of elasticity and bending of plates, in which the coal seam roof is represented as a model of a rectangular plate or a beam with a symmetrical cross-section with different support conditions. Results. To substantiate and select methods for studying the bending deformations of the roof in the coal massif containing the maingates, the three-dimensional base plate model and the beam model are compared, taking into account the kinematic boundary conditions and the influence of external distributed load. Using the theory of plate bending, the equations for determining the deflections of the coal seam roof in three-dimensional basic models under certain assumptions have a large dimension. After the conditional division of the plate into beams of unit width and symmetrical section, when describing the normal deflections of the middle surface of the studied models, the transition from the partial derivative equation to the usual differential equations is carried out. In this case, the studies of bending deformations of roof rocks are reduced to solving a flat problem in the cross-section of the beam. A comparison of solutions obtained by the methods of the three-dimensional theory of elasticity and strength of materials was performed. For a beam with a symmetrical section, the deflection lies in a plane whose angle of inclination coincides with the direction of the applied load. The calculations did not take into account the difference between the intensity of the surface load applied to the beam. Differences in determining the magnitude of the deflections of the roof in the model of the plate concerning the model of the beam reach 5%, which is acceptable for mining problems. Scientific novelty. To study the bending deformations and determine the magnitude of the roof deflection in models under external uniform distributed load, placed within the simulated plate, a strip of unit width was selected, which has a symmetrical cross-section and is a characteristic component of the plate structure and it is considered as a separate load-bearing element with supports, the cross-sections of this element is remained flat when bending. The deflection of such a linear element is described by the differential equations of the bent axis of the beam without taking into account the integral stiffness of the model, and the vector of its complete displacement coincides with the vector of the force line. Practical significance. In the laboratory, to study the bending deformations and their impact on the stability of the coal seam roof under external loads, it is advisable to use a model of a single width beam with a symmetrical section with supports, the type of which is determined by rock pressure control and secondary support of the maingate at the extraction layout of the coal mine.
- 1 January 2021
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- No. 1
SUBSTANTIATION FOR SIMPLIFICATION OF CALCULATION MODELS FOR ASSESSMENT OF THE STABILITY OF ROOF ROCKS
Purpose. Substantiation of expediency and admissibility of use of the simplified calculation models of a coal seam roof for an estimation of its stability under the action of external loadings. Methods. To achieve this purpose, the studies have been performed using the basic principles of the theory of elasticity and bending of plates, in which the coal seam roof is represented as a model of a rectangular plate or a beam with a symmetrical cross-section with different support conditions. Results. To substantiate and select methods for studying the bending deformations of the roof in the coal massif containing the maingates, the three-dimensional base plate model and the beam model are compared, taking into account the kinematic boundary conditions and the influence of external distributed load. Using the theory of plate bending, the equations for determining the deflections of the coal seam roof in three-dimensional basic models under certain assumptions have a large dimension. After the conditional division of the plate into beams of unit width and symmetrical section, when describing the normal deflections of the middle surface of the studied models, the transition from the partial derivative equation to the usual differential equations is carried out. In this case, the studies of bending deformations of roof rocks are reduced to solving a flat problem in the cross-section of the beam. A comparison of solutions obtained by the methods of the three-dimensional theory of elasticity and strength of materials was performed. For a beam with a symmetrical section, the deflection lies in a plane whose angle of inclination coincides with the direction of the applied load. The calculations did not take into account the difference between the intensity of the surface load applied to the beam. Differences in determining the magnitude of the deflections of the roof in the model of the plate concerning the model of the beam reach 5%, which is acceptable for mining problems. Scientific novelty. To study the bending deformations and determine the magnitude of the roof deflection in models under external uniform distributed load, placed within the simulated plate, a strip of unit width was selected, which has a symmetrical cross-section and is a characteristic component of the plate structure and it is considered as a separate load-bearing element with supports, the cross-sections of this element is remained flat when bending. The deflection of such a linear element is described by the differential equations of the bent axis of the beam without taking into account the integral stiffness of the model, and the vector of its complete displacement coincides with the vector of the force line. Practical significance. In the laboratory, to study the bending deformations and their impact on the stability of the coal seam roof under external loads, it is advisable to use a model of a single width beam with a symmetrical section with supports, the type of which is determined by rock pressure control and secondary support of the maingate at the extraction layout of the coal mine.
- 1 January 2020
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- No. 2,p. 7-22
EXPERIMENTAL STUDIES OF DEFORMATION CHARACTERISTICS OF MINE PROTECTION STRUCTURES
The purpose of the article. Studying deformation characteristics of protective structures under the influence of external loads used to maintain lateral rocks in the coal massif behind the production face. Methods. To achieve this goal, laboratory studies of the deformation characteristics of security structures under uniaxial compression were performed. Results. As a result of the research it has been established that at uniaxial compression of wooden protective constructions in the form of rolling fires from sleepers or bushes from risers, change of their rigidity is caused both by differences in properties of wood at action of external force along or across fibres, and design features. In cases where a constant compressive force is applied to the experimental sample across the fibres (rolling fires from sleepers), the change in stiffness is quadratic and reaches minimum values when the deformation of the model by 30-35%, and with a further increase in deformation to 50% stiffness increases. This indicates an increase in the resistance of rolling fires to external loads after their compression, without losing the strength of the structure. Under the action of compressive force along the fibres (bushes of risers), the stiffness of the experimental samples increases until the moment of destruction, when there is a loss of strength of the structure. The change in the stiffness of embedded arrays of crushed rock, if possible, their lateral expansion occurs due to the compaction of embedded material, i.e. recomposition of particles of crushed rock of different fractions in the total volume. Novelty. The nature of the deformation of security structures considered as prefabricated structures can be described by the change in the specific potential deformation energy spent on changing the shape and/or volume of the protective structures. Practical meaning. To ensure the stability of the side rocks in the coal massif containing the workings, it is necessary to focus on the use of flexible protection structures located above the retractable roadway.
- 1 January 2020
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- No. 2,p. 7-22
EXPERIMENTAL STUDIES OF DEFORMATION CHARACTERISTICS OF MINE PROTECTION STRUCTURES
The purpose of the article. Studying deformation characteristics of protective structures under the influence of external loads used to maintain lateral rocks in the coal massif behind the production face. Methods. To achieve this goal, laboratory studies of the deformation characteristics of security structures under uniaxial compression were performed. Results. As a result of the research it has been established that at uniaxial compression of wooden protective constructions in the form of rolling fires from sleepers or bushes from risers, change of their rigidity is caused both by differences in properties of wood at action of external force along or across fibres, and design features. In cases where a constant compressive force is applied to the experimental sample across the fibres (rolling fires from sleepers), the change in stiffness is quadratic and reaches minimum values when the deformation of the model by 30-35%, and with a further increase in deformation to 50% stiffness increases. This indicates an increase in the resistance of rolling fires to external loads after their compression, without losing the strength of the structure. Under the action of compressive force along the fibres (bushes of risers), the stiffness of the experimental samples increases until the moment of destruction, when there is a loss of strength of the structure. The change in the stiffness of embedded arrays of crushed rock, if possible, their lateral expansion occurs due to the compaction of embedded material, i.e. recomposition of particles of crushed rock of different fractions in the total volume. Novelty. The nature of the deformation of security structures considered as prefabricated structures can be described by the change in the specific potential deformation energy spent on changing the shape and/or volume of the protective structures. Practical meaning. To ensure the stability of the side rocks in the coal massif containing the workings, it is necessary to focus on the use of flexible protection structures located above the retractable roadway.
- Open Access
- 28 September 2019
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: New solutions in modern technologies
- No. 1,p. 48-57
Study on models of stability of side species at extreme damage of a divided thickness
Дослідження на моделях стійкості бічних порід при раптових обваленнях розшарованої товщі
- 28 September 2019
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: New solutions in modern technologies
- No. 1,p. 48-57
Open AccessStudy on models of stability of side species at extreme damage of a divided thickness
Дослідження на моделях стійкості бічних порід при раптових обваленнях розшарованої товщі