Cong Cui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cong Cui has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Xili Duan
Faculty of Engineering and Applied Science, Memorial University of Newfoundland, St. John’s, Canada
3 shared publications - Ali Nasiri
Department of Mechanical Engineering, Dalhousie University, Halifax, Canada
1 shared publication - Brandon Collier
Department of Physics and Physical Oceanography, Memorial University of Newfoundland, 230 Elizabeth Avenue, St. John's, NL A1B 3X7, Canada
1 shared publication - Jaffer Alkarim Jaffer
Faculty of Engineering and Applied Science, Memorial University of Newfoundland, St. John’s, NL A1B 3X5, Canada
1 shared publication - Kristin M. Poduska
Department of Chemistry, Memorial University of Newfoundland & Labrador, St. John’s, NL A1C 5S7, Canada
1 shared publication - Mehran Rafieazad
Faculty of Engineering and Applied Science, Memorial University of Newfoundland, St. John’s, Canada
1 shared publication
Latest Publications
- Open Access
Nanosecond Laser Fabrication of Hydrophobic Stainless Steel Surfaces: The Impact on Microstructure and Corrosion Resistance
Creation of hydrophobic and superhydrophobic surfaces has attracted broad attention as a promising solution for protection of metal surfaces from corrosive environments. This work investigates the capability of nanosecond fiber laser surface texturing followed by a low energy coating in the fabrication of hydrophobic 17-4 PH stainless steel surfaces as an alternative to the ultrashort lasers previously utilized for hydrophobic surfaces production. Laser texturing of the surface followed by applying the hydrophobic coating resulted in steady-state contact angles of up to 145°, while the non-textured coated base metal exhibited the contact angle of 121°. The microstructure and compositional analysis results confirmed that the laser texturing process neither affects the microstructure of the base metal nor causes elemental loss from the melted regions during the ultrafast melting process. However, the electrochemical measurements demonstrated that the water-repelling property of the surface did not contribute to the anticorrosion capability of the substrate. The resultant higher corrosion current density, lower corrosion potential, and higher corrosion rate of the laser textured surfaces were ascribed to the size of fabricated surface micro-grooves, which cannot retain the entrapped air inside the hierarchical structure when fully immersed in a corrosive medium, thus degrading the material’s corrosion performance.
Open AccessNanosecond Laser Fabrication of Hydrophobic Stainless Steel Surfaces: The Impact on Microstructure and Corrosion Resistance
Creation of hydrophobic and superhydrophobic surfaces has attracted broad attention as a promising solution for protection of metal surfaces from corrosive environments. This work investigates the capability of nanosecond fiber laser surface texturing followed by a low energy coating in the fabrication of hydrophobic 17-4 PH stainless steel surfaces as an alternative to the ultrashort lasers previously utilized for hydrophobic surfaces production. Laser texturing of the surface followed by applying the hydrophobic coating resulted in steady-state contact angles of up to 145°, while the non-textured coated base metal exhibited the contact angle of 121°. The microstructure and compositional analysis results confirmed that the laser texturing process neither affects the microstructure of the base metal nor causes elemental loss from the melted regions during the ultrafast melting process. However, the electrochemical measurements demonstrated that the water-repelling property of the surface did not contribute to the anticorrosion capability of the substrate. The resultant higher corrosion current density, lower corrosion potential, and higher corrosion rate of the laser textured surfaces were ascribed to the size of fabricated surface micro-grooves, which cannot retain the entrapped air inside the hierarchical structure when fully immersed in a corrosive medium, thus degrading the material’s corrosion performance.
- 22 June 2018
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 6 (3) , 031006
Fabrication and Wettability Analysis of Hydrophobic Stainless Steel Surfaces With Microscale Structures From Nanosecond Laser Machining
In this work, nanosecond laser machining is used to fabricate hydrophobic 17-4 PH stainless steel surfaces with microscale and submicron structures. Four surface structures were designed, with microscale channels and pillars (100 μm pitch size) of uniform heights (100 μm) or alternating heights (between 100 μm and 50 μm). During fabrication, the high-power laser beams also created submicron features on top of the microscale ones, leading to hierarchical, multiscale surface structures. Detailed wettability analysis was conducted on the fabricated samples. Measured static contact angles of water on these surfaces are over 130 deg without any coating, compared to ∼70 deg on the original steel surface before laser machining. Slightly lower contact angle hysteresis was also observed on the laser machined surfaces. Overall, these results agree with a simple Cassie–Baxter model for wetting that assumes only fractional surface area contact between the droplet and the surface. This work demonstrates that steel surfaces machined with relatively inexpensive nanosecond laser can achieve excellent hydrophobicity even with simple microstructural designs.
- 22 June 2018
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 6 (3) , 031006
Fabrication and Wettability Analysis of Hydrophobic Stainless Steel Surfaces With Microscale Structures From Nanosecond Laser Machining
In this work, nanosecond laser machining is used to fabricate hydrophobic 17-4 PH stainless steel surfaces with microscale and submicron structures. Four surface structures were designed, with microscale channels and pillars (100 μm pitch size) of uniform heights (100 μm) or alternating heights (between 100 μm and 50 μm). During fabrication, the high-power laser beams also created submicron features on top of the microscale ones, leading to hierarchical, multiscale surface structures. Detailed wettability analysis was conducted on the fabricated samples. Measured static contact angles of water on these surfaces are over 130 deg without any coating, compared to ∼70 deg on the original steel surface before laser machining. Slightly lower contact angle hysteresis was also observed on the laser machined surfaces. Overall, these results agree with a simple Cassie–Baxter model for wetting that assumes only fractional surface area contact between the droplet and the surface. This work demonstrates that steel surfaces machined with relatively inexpensive nanosecond laser can achieve excellent hydrophobicity even with simple microstructural designs.
- 1 September 2016
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 40 (3) , 253-263
DESIGN AND TESTING OF A NEW WATER SUPPLY DEVICE
When water is supplied from pressurized pipelines, the high pressure often causes waste of water by splashing and unnecessarily high flow rates. In this research, an innovative new water supply device is designed to overcome this problem. In this device water is supplied in the form of overflow by automatically adjusting water pressure at the inlet. This paper presents the mechanical design of the new faucet and explains how it operates in sensor mode and bypass mode. Experimental results show that the new design achieves near-zero outflow pressure and can still provide rapid water supply when required.
- 1 September 2016
- Published by Canadian Science Publishing in Transactions of the Canadian Society for Mechanical Engineering
- Vol. 40 (3) , 253-263
DESIGN AND TESTING OF A NEW WATER SUPPLY DEVICE
When water is supplied from pressurized pipelines, the high pressure often causes waste of water by splashing and unnecessarily high flow rates. In this research, an innovative new water supply device is designed to overcome this problem. In this device water is supplied in the form of overflow by automatically adjusting water pressure at the inlet. This paper presents the mechanical design of the new faucet and explains how it operates in sensor mode and bypass mode. Experimental results show that the new design achieves near-zero outflow pressure and can still provide rapid water supply when required.