Ruimin Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ruimin Liu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Gaofeng Zheng
Pen‐Tung Sah Institute of Micro‐Nano Science and Technology Xiamen University Xiamen China
2 shared publications - Shumin Guo
Fujian Provincial Key Laboratory of Mathematical Modeling and High Performance Scientific Computing, School of Mathematical Sciences, Xiamen University, Xiamen 361005, China
2 shared publications - Yifang Liu
Pen-Tung Sah Institute of Micro-Nano Science and Technology, Xiamen University, Xiamen 361102, China
2 shared publications - Cheng Li
Department of Aeronautical and Aviation Engineering, Hong Kong Polytechnic University, Hong Kong 999077, China
1 shared publication - Jiaxin Jiang
Department of Instrumental and Electrical Engineering, Xiamen University, Xiamen 361102, China
1 shared publication - Juan Liu
Pen-Tung Sah Institute of Micro-Nano Science and Technology, Xiamen University, Xiamen, China
1 shared publication
Latest Publications
- Open Access
Adaptive Fuzzy Modal Matching of Capacitive Micromachined Gyro Electrostatic Controlling
A fuzzy PI controller was utilized to realize the modal matching between a driving and detecting model. A simulation model was built to study electrostatic decoupling controlling technology. The simulation results show that the modal matching can be gained by the fuzzy PI controller. The frequency difference between the driving mode and the detection mode is less than 1 Hz, and the offset of the input DC is smaller than 0.6 V. The optimal proportionality factor and integral coefficient are 1.5 and 20, respectively. The fuzzy PI controlling technology provides a good way for the parameter optimization to gain modal matching of micro gyro, via which the detecting accuracy and stability can be improved greatly.
Open AccessAdaptive Fuzzy Modal Matching of Capacitive Micromachined Gyro Electrostatic Controlling
A fuzzy PI controller was utilized to realize the modal matching between a driving and detecting model. A simulation model was built to study electrostatic decoupling controlling technology. The simulation results show that the modal matching can be gained by the fuzzy PI controller. The frequency difference between the driving mode and the detection mode is less than 1 Hz, and the offset of the input DC is smaller than 0.6 V. The optimal proportionality factor and integral coefficient are 1.5 and 20, respectively. The fuzzy PI controlling technology provides a good way for the parameter optimization to gain modal matching of micro gyro, via which the detecting accuracy and stability can be improved greatly.
- Open Access
- 24 August 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (9) , 427
Electrospun Three-Dimensional Nanofibrous Structure via Probe Arrays Inducing
The fast and precise direct-printing of micro three-dimensional (3D) structures is the important development trend for micro/nano fabrication technique. A novel method with probe arrays was built up to realize the controllable deposition of 3D electrospun nanofibrous structures. Firstly, several 3D nanofibrous structures were built on a single probe and 2-, 3-probes, which indicated that the probe height and probe interval played a key role on the 3D structure morphology. Then, different stereo nanofibrous structures based on multiprobe arrays were achieved accurately and the effects of processing parameters, including the probe height, probe interval, applied voltage and flow rate on the deposition behaviors of electrospun nanofiber over the probe arrays were investigated. The deposition area of 3D electrospun nanofibrous structures decreased with the increase of probe interval, applied voltage, and flow rate. Several 3D nanofibrous structures of special shapes including convex, triangle wave, inverted cone and complex curved surface were demonstrated by controlling the configuration of probe arrays and electrospinning parameters. This work provides an effective and simple way for the construction of 3D electrospun nanofibrous structures, which has great potentials in various medical and industrial applications.
- 24 August 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (9) , 427
Open AccessElectrospun Three-Dimensional Nanofibrous Structure via Probe Arrays Inducing
The fast and precise direct-printing of micro three-dimensional (3D) structures is the important development trend for micro/nano fabrication technique. A novel method with probe arrays was built up to realize the controllable deposition of 3D electrospun nanofibrous structures. Firstly, several 3D nanofibrous structures were built on a single probe and 2-, 3-probes, which indicated that the probe height and probe interval played a key role on the 3D structure morphology. Then, different stereo nanofibrous structures based on multiprobe arrays were achieved accurately and the effects of processing parameters, including the probe height, probe interval, applied voltage and flow rate on the deposition behaviors of electrospun nanofiber over the probe arrays were investigated. The deposition area of 3D electrospun nanofibrous structures decreased with the increase of probe interval, applied voltage, and flow rate. Several 3D nanofibrous structures of special shapes including convex, triangle wave, inverted cone and complex curved surface were demonstrated by controlling the configuration of probe arrays and electrospinning parameters. This work provides an effective and simple way for the construction of 3D electrospun nanofibrous structures, which has great potentials in various medical and industrial applications.