Chuan Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chuan Ding has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Fan Ding
The State Key Lab of Fluid Power Transmission and Control, Zhejiang University, Hangzhou 310027, China
2 shared publications - Shuo Liu
Ocean Academy, Zhejiang University, Zhoushan 316000, China
2 shared publications - Canjun Yang
Department of Mechanical Engineering, Zhejiang University, Hangzhou, China
1 shared publication - Xing Zhou1 shared publication
- Zaipeng Man
The State Key Lab of Fluid Power Transmission and Control, Zhejiang University, Hangzhou 310027, China
1 shared publication
Latest Publications
- Open Access
A High-Pressure Bi-Directional Cycloid Rotor Flowmeter
The measurement of the flow rate of various liquids and gases is critical in industrial automation. Rotary positive displacement meters (rotary PD meters) are highly accurate flowmeters that are widely employed in engineering applications, especially in custody transfer operations and hydraulic control systems. This paper presents a high pressure rotary PD meter containing a pair of internal cycloid rotors. It has the advantages of concise structure, low pressure loss, high accuracy and low noise. The curve of the internal rotor is designed as an equidistant curtate epicycloid curve with the external rotor curve as its conjugate. The calculation method used to determine the displacement of the cycloid rotor flowmeter is discussed. A prototype was fabricated, and experiments were performed to confirm measurements over a flow range of 1–100 L/min with relative errors of less than ±0.5%. The pressure loss through the flowmeter was about 3 bar at a flow rate of 100 L/min.
Open AccessA High-Pressure Bi-Directional Cycloid Rotor Flowmeter
The measurement of the flow rate of various liquids and gases is critical in industrial automation. Rotary positive displacement meters (rotary PD meters) are highly accurate flowmeters that are widely employed in engineering applications, especially in custody transfer operations and hydraulic control systems. This paper presents a high pressure rotary PD meter containing a pair of internal cycloid rotors. It has the advantages of concise structure, low pressure loss, high accuracy and low noise. The curve of the internal rotor is designed as an equidistant curtate epicycloid curve with the external rotor curve as its conjugate. The calculation method used to determine the displacement of the cycloid rotor flowmeter is discussed. A prototype was fabricated, and experiments were performed to confirm measurements over a flow range of 1–100 L/min with relative errors of less than ±0.5%. The pressure loss through the flowmeter was about 3 bar at a flow rate of 100 L/min.
- 18 September 2013
- Published by Wiley in Journal of Mechanical Design
- Vol. 135 (12) , 125001
Novel Pressure-Resistant Oil-Immersed Proportional Actuator for Electrohydraulic Proportional Control Valve
This paper presents a novel pressure-resistant oil-immersed proportional actuator with a magnetic grid magnetic-isolated ring (MGMR) on its single-piece sleeve. A two-dimensional finite element method is used to establish the model and analyze the static and dynamic performance. The experimental and simulation results agree well with each other and verify the static and dynamic performance characteristics of this proportional actuator. The results indicate that the actuator can produce 15 N force output when the ampere turns is 450AT in 2.2-mm wide working stroke; the rising step response time and the falling step response time are 24 and 17 ms, respectively, and the frequency response (−3dB) is 25 Hz. Consequently, its applications to electrohydraulic proportional/servo valve are acceptable.
- 18 September 2013
- Published by Wiley in Journal of Mechanical Design
- Vol. 135 (12) , 125001
Novel Pressure-Resistant Oil-Immersed Proportional Actuator for Electrohydraulic Proportional Control Valve
This paper presents a novel pressure-resistant oil-immersed proportional actuator with a magnetic grid magnetic-isolated ring (MGMR) on its single-piece sleeve. A two-dimensional finite element method is used to establish the model and analyze the static and dynamic performance. The experimental and simulation results agree well with each other and verify the static and dynamic performance characteristics of this proportional actuator. The results indicate that the actuator can produce 15 N force output when the ampere turns is 450AT in 2.2-mm wide working stroke; the rising step response time and the falling step response time are 24 and 17 ms, respectively, and the frequency response (−3dB) is 25 Hz. Consequently, its applications to electrohydraulic proportional/servo valve are acceptable.