Christina Back
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Christina Back has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Christopher D. Haines
US Army Armament Research Development Engineering Center, Picatinny Arsenal, NJ 07806, USA
2 shared publications - Eugene A. Olevsky
San Diego State University, San Diego, USA
2 shared publications - Oleg Izhvanov
General Atomics, 3350 General Atomics Ct., San Diego, CA 92121, USA
2 shared publications - Xialu Wei
Department of Mechanical Engineering, San Diego State University, 5500 Campanile Dr., San Diego, CA 92182, USA
2 shared publications - Oleg L. Khasanov
National Research Tomsk Polytechnic University
1 shared publication - Robert Schleicher
General Atomics, 3550 General Atomics Ct., San Diego CA 92121
1 shared publication
Latest Publications
- Open Access
Zirconium Carbide Produced by Spark Plasma Sintering and Hot Pressing: Densification Kinetics, Grain Growth, and Thermal Properties
Spark plasma sintering (SPS) has been employed to consolidate a micron-sized zirconium carbide (ZrC) powder. ZrC pellets with a variety of relative densities are obtained under different processing parameters. The densification kinetics of ZrC powders subjected to conventional hot pressing and SPS are comparatively studied by applying similar heating and loading profiles. Due to the lack of electric current assistance, the conventional hot pressing appears to impose lower strain rate sensitivity and higher activation energy values than those which correspond to the SPS processing. A finite element simulation is used to analyze the temperature evolution within the volume of ZrC specimens subjected to SPS. The control mechanism for grain growth during the final SPS stage is studied via a recently modified model, in which the grain growth rate dependence on porosity is incorporated. The constant pressure specific heat and thermal conductivity of the SPS-processed ZrC are determined to be higher than those reported for the hot-pressed ZrC and the benefits of applying SPS are indicated accordingly.
Open AccessZirconium Carbide Produced by Spark Plasma Sintering and Hot Pressing: Densification Kinetics, Grain Growth, and Thermal Properties
Spark plasma sintering (SPS) has been employed to consolidate a micron-sized zirconium carbide (ZrC) powder. ZrC pellets with a variety of relative densities are obtained under different processing parameters. The densification kinetics of ZrC powders subjected to conventional hot pressing and SPS are comparatively studied by applying similar heating and loading profiles. Due to the lack of electric current assistance, the conventional hot pressing appears to impose lower strain rate sensitivity and higher activation energy values than those which correspond to the SPS processing. A finite element simulation is used to analyze the temperature evolution within the volume of ZrC specimens subjected to SPS. The control mechanism for grain growth during the final SPS stage is studied via a recently modified model, in which the grain growth rate dependence on porosity is incorporated. The constant pressure specific heat and thermal conductivity of the SPS-processed ZrC are determined to be higher than those reported for the hot-pressed ZrC and the benefits of applying SPS are indicated accordingly.
- Open Access
Spark Plasma Sintering of Commercial Zirconium Carbide Powders: Densification Behavior and Mechanical Properties
Commercial zirconium carbide (ZrC) powder is consolidated by Spark Plasma Sintering (SPS). Processing temperatures range from 1650 to 2100 °C. Specimens with various density levels are obtained when performing single-die SPS at different temperatures. Besides the single-die tooling setup, a double-die tooling setup is employed to largely increase the actual applied pressure to achieve higher densification in a shorter processing time. In order to describe the densification mechanism of ZrC powder under SPS conditions, a power-law creep constitutive equation is utilized, whose coefficients are determined by the inverse regression of the obtained experimental data. The densification of the selected ZrC powder is shown to be likely associated with grain boundary sliding and dislocation glide controlled creep. Transverse rupture strength and microhardness of sintered specimens are measured to be up to 380 MPa and 24 GPa, respectively. Mechanical properties are correlated with specimens’ average grain size and relative density to elucidate the co-factor dependencies.
Open AccessSpark Plasma Sintering of Commercial Zirconium Carbide Powders: Densification Behavior and Mechanical Properties
Commercial zirconium carbide (ZrC) powder is consolidated by Spark Plasma Sintering (SPS). Processing temperatures range from 1650 to 2100 °C. Specimens with various density levels are obtained when performing single-die SPS at different temperatures. Besides the single-die tooling setup, a double-die tooling setup is employed to largely increase the actual applied pressure to achieve higher densification in a shorter processing time. In order to describe the densification mechanism of ZrC powder under SPS conditions, a power-law creep constitutive equation is utilized, whose coefficients are determined by the inverse regression of the obtained experimental data. The densification of the selected ZrC powder is shown to be likely associated with grain boundary sliding and dislocation glide controlled creep. Transverse rupture strength and microhardness of sintered specimens are measured to be up to 380 MPa and 24 GPa, respectively. Mechanical properties are correlated with specimens’ average grain size and relative density to elucidate the co-factor dependencies.
- 1 January 2012
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 61 (1T) , 144-149
Configuring EM2to Meet the Challenges of Economics, Waste Disposition and Non-Proliferation Confronting Nuclear Energy in the U.S.
General Atomics (GA) is developing a new nuclear concept called Energy Multiplier Module (EM2), which is a helium (He) cooled fast reactor with a net electrical output of 240 MW. It employs a “convert & burn” core design which converts fertile to fissile and burns it in situ over a 30-year core life. It can burn SNF from LWRs with no reprocessing, only refabrication. The core can be recycled using an AIROX-based method to remove a fraction of the fission products (FPs) but no heavy metals. The reactor is passively safe and sited below grade. It can sustain a Fukushima type station blackout or even a station blackout combined with a loss of coolant accident using only passive safety systems without radioactivity release or loss of plant. The afterheat is rejected directly to the air. It is a high temperature reactor and employs a direct closed-cycle gas turbine for 48% net efficiency. The reject heat can be released directly to air so that siting near a large water source is not required. GA is targeting a...
- 1 January 2012
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 61 (1T) , 144-149
Configuring EM2to Meet the Challenges of Economics, Waste Disposition and Non-Proliferation Confronting Nuclear Energy in the U.S.
General Atomics (GA) is developing a new nuclear concept called Energy Multiplier Module (EM2), which is a helium (He) cooled fast reactor with a net electrical output of 240 MW. It employs a “convert & burn” core design which converts fertile to fissile and burns it in situ over a 30-year core life. It can burn SNF from LWRs with no reprocessing, only refabrication. The core can be recycled using an AIROX-based method to remove a fraction of the fission products (FPs) but no heavy metals. The reactor is passively safe and sited below grade. It can sustain a Fukushima type station blackout or even a station blackout combined with a loss of coolant accident using only passive safety systems without radioactivity release or loss of plant. The afterheat is rejected directly to the air. It is a high temperature reactor and employs a direct closed-cycle gas turbine for 48% net efficiency. The reject heat can be released directly to air so that siting near a large water source is not required. GA is targeting a...